ACCENTRA Holder Stop Arm Door Closers

Product Information

Specifications:

• Model Numbers Included:
  • PR40X NHO 2 THRU 6
  • PR140X HO
  • PR4400 NHO 1-6
  • PR4410 HO
  • 402X NHO 2 THRU 6
  • 402XT HO
  • 4420 NHO 1-6
  • 4420T HO
• X Designates closer size: 2, 3, 4, 5, or
  6

Product Usage Instructions:

Standard Frame Installation:

Closer mounts on the opposite side of the hinge (push side) of
the door. PR4400 Parallel Rigid Non Hold Open arm is
illustrated.

Narrow Frame Installation:

Closer mounts on the opposite side of the hinge (push side) of
the door. 4420 Holder-Stop arm is illustrated. 6890 and 6891
accessories are required for this application.

Flush Partition Installation:

Closer mounts on the opposite side of the hinge (push side) of
the door. 44420T Holder-Stop arm with Thumbturn Hold Open is
illustrated. The 2019L accessory is required for this
application.

Components:

The product includes various components such as Standard/Delayed
Action Options, Power Adjustment Shaft Screw Pack, Arm Options,
Removable Stop, Soffit Plate, Closer Arm, Secondary Arm, and more
as listed in the manual.

Preparation for Fasteners:

Different fasteners are required based on the material of the
door or frame. Self-drilling screws, machine screws, sleeve nuts
and bolts, and through-bolts are some of the options provided with
specific drill sizes mentioned in the manual.

FAQ:

Q: What should I do if the door closer is not functioning

properly?

A: In case of any issues with the door closer’s functionality,
first ensure that it is correctly installed and adjusted according
to the provided instructions. If problems persist, contact customer
support for further assistance.

Q: Are there different sizes available for the door

closers?

A: Yes, the model numbers include various sizing options ranging
from 2 to 6 to accommodate different door dimensions.

Installation Instructions
80-9344-2205-010 (09-11)

CAUTION

CAUTION

Parallel Rigid Arm Door Closers (PR) Holder-Stop Arm Door Closers

An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment.

Additional Closer Options: – “DL” indicates Delayed Action closing. – Hold- Open function components are handed – “T” indicates Thumbturn actuated Hold- Open control. Optional Accessories: – 488 Drop Plate – 293L, 890, 891 Soffit Plate Accessories.

Model Numbers Included:

Series Function Sizing

Parallel Rigid Arm Units

PR40X

NHO 2 THRU 6

PR140X HO

”

PR4400 NHO

1-6

PR4410

HO

”

Holder-Stop Units

402X

NHO 2 THRU 6

402XT

HO

”

4420

NHO

1-6

4420T

HO

”

“X” Designates closer size 2, 3, 4, 5, or 6

NOTE: For special applications a separate door and frame preparation template is packed with these instructions. In those cases, use this instruction sheet for installation sequence and closer adjustments only.

Standard Frame Installation
Closer mounts on opposite to hinge (push) side of door. PR4400 Parallel Rigid Non Hold Open arm illustrated.
See Pages 3 and 4

Hinge Edge of Door

Hinge Edge of Door

Right Hand Door ­ RH Left Hand Reverse ­ LHR

Left Hand Door ­ LH Right Hand Reverse ­ RHR

Narrow Frame Installation
Closer mounts on opposite to hinge (push) side of door. 4420 Holder-Stop arm illustrated. 6890 and 6891 accessories required for this application (supplied separately).
See Pages 3 and 4

Hinge Edge of Door

Hinge Edge of Door

Right Hand Door ­ RH Left Hand Reverse ­ LHR

Left Hand Door ­ LH Right Hand Reverse ­ RHR

Flush Partition Installation
Closer mounts on opposite to hinge (push) side of door. 44420T Holder-Stop arm with Thumbturn Hold Open illustrated. 2019L accessory required for this application (supplied separately).
See Pages 3 and 4

Hinge Edge of Door

Hinge Edge of Door

Right Hand Door ­ RH Left Hand Reverse ­ LHR

Left Hand Door ­ LH Right Hand Reverse ­ RHR

Components

LS D

P BC

L S

P BC

Standard

Delayed Action Option
Power Adjustment Shaft Screw Pack

Arm Options

Removable Stop

Soffit Plate
Closer Arm
Secondary Arm

293S Block (provided)

Optional Accessories

For Blade Stop

Main Arm

891 Spacer

Screw

For Frame

or Blade Stop

Main Arm 890 Bracket

For Flush Partition 293L Bracket

Friction Hold Open Nut

Removable Stop

Riveted Elbow
PR Arm Assembly

Riveted Elbow
Holder-Stop Arm Assembly Stop only

Cover Options

Plastic Cover (Standard)
2 Cover Screws

Riveted Elbow
PR Hold Open Arm Assembly

Thumbturn Hold Open
Riveted Elbow
Holder-Stop Arm Assembly with Thumbturn

Metal Cover (Optional)

Page 2

Standard Optional

Preparation for Fasteners

Fasteners

Door or Frame Drill-Sizes

Self-Drilling Screw 1/4″ – 20 machine screw

Aluminum or Metal
Wood
Metal

No drill required
3/16″ (4.30 mm) Pilot hole required Drill: #7 (0.201″ dia.) Tap: 1/4″ – 20

Sleeve nuts and bolts
Through-bolts and grommet-nuts

Hollow Metal Aluminum or Wood
All

9/32″ (7 mm) through; 3/8″ (9.5 mm) door face opposite to closer
3/8″ (9.5 mm) through
9/32″ (7 mm); 3/8″ (9.5 mm) dia. x 3/8″ (9.5 mm) deep on door opposite to closer

80-9344-2205-010 (09-11)

Installation Instructions
Select angle of opening and use dimensions shown on Page 4 and Dimension Chart below to locate 4 holes on door for closer body (or 4 holes for 488 Drop Plate, Page 5, only if required) and 5 holes on stop/rabbet for Soffit Plate (or 4 holes on frame transom for 293L bracket, only if required). For applications not covered in these instructions, a separate template will be required.
Prepare door and frame for fasteners using “Preparation for Fasteners” chart on Page 2.
Mount 488 Drop Plate to door … only if used (see Page 5).
Install closer body to door, or 488 Drop Plate, with power adjustment shaft away from hinge edge of door and adjustment valves:
Down for Left Hand Up for Right Hand
Check arm handing for all CLP and PR arms with Hold open Feature.
CLP Arms are shipped as left hand for right hand doors, switch positions of soffit plate stop and Hole Plug.
PR Hold Open Arms are handed and not reversible. See handing marks on soffit plate.
CPS arms only: With door partially open to allow clearance, install CPS arm kit to arm’s soffit plate.

Power Adjustment Chart

Maximum Interior
Door Size
inches (mm)
32 (0.81)
36 (0.91)
42 (1.07)
52 (1.32)
60 (1.52)

Maximum Exterior
Door Size
inches (mm)
28 (0.70)
34 (0.86)
38 (.96)
42 (1.07)
48 (1.22)

4400 Series Only Full Clockwise Turns of Closer Power Adjustment
Nut (from “0” turns)
5 8-1/2
11
13-1/2 16-1/2

NOTE: Maximum of 16-1/2 turns (360°) of Power Adjustment Nut. Closer is shipped set at 8 turns from the factory.

Install closer per instructions with the proper pre-load applied to the arm then adjust spring power. The power adjustment will not work properly if the closer spring is not pre-loaded.

80-9344-2205-010 (09-11) Install Main Arm: Close valves (S/D’ orS’) and L’, then using a wrench, rotate the pinion shaft at least 50° to permit alignment of the Pinion Flat with the proper arm mark: Z’ for Left Hand Y’ for Right Hand See below for illustrations of this procedure. Reopen valves (S/D’ or S’) andL’, that were closed in previous step. With door closed, align soffit plate with holes in frame and fasten to frame with screws. Use 293S and/or 891spacer blocks or 890 reinforcing bracket as required. Make adjustments to closer before installing cover. See Page 6 for closer adjustment instructions. CAUTION: Do Not back valves out of closer body or a fluid leak will result.
Install cover.
Arm Mounting Detail
Pinion flat will face the door on either right or
left hand doors.
Arm to Pinion Assembly

ROTAT E

Install arm roughly here with flat side of pinion to the correct marking on the arm
per the illustration below

“Z”

“Y”

L

R

S Z R

YS L

Y

Z

Final Installation

DO NOT use a power drill or driver to turn adjustment nut. This will damage closer and void warranty.

80-9344-2205-010 (09-11)

Page 3

Standard Frame
B 3/8 (10)
2-1/16 (52)
CLHinge or Pivot

2-3/4 (70) 2 (51)
1-3/8 (35)

Standard Mount

Blade Stop Mount 5/8 Ref.
(16)

1/2 (13)

Soffit Plate
Notes: Do Not Scale Drawing.

Soffit Plate 293S Block

Left Hand Door Shown.

7/16 (11)

Same dimensions apply for Right Hand Door measured from centerline of pivot point. Dimensions are in inches (mm).

See Page 3 for A, B, or C dimension values.

891 Block

2-1/2 (64)
2-3/8 (60)
A
Narrow Frame
3/8 (10)
CLHinge or Pivot B

6-3/4 (172)
2-3/4 (70) 2 (51)

PR PREFIX
CLP &
CPS PREFIX

Dim
A in. (mm)
B in. (mm)
C in. (mm)
A in. (mm)
B in. (mm)
C in. (mm)

Installation Dimensions Chart

Up to 90°-

90°

95°

95°100°

100°105°

105°110°

110°115°

115°130°

8-3/4

7-1/4

(222)

(184)

9-1/4

7-3/4

(235)

(197)

9-3/8

7-7/8

(238)

(200)

10-1/8 9-1/4 8-5/8 7-7/8 7-3/8 6-3/4

(257) (235) (219) (200) (187) (171)

10-5/8 9-3/4 9-1/8 8-3/8 7-7/8 7-1/4

(270) (248) (232) (213) (200) (184)

10-3/4 9-7/8 9-1/4 8-1/2 8 7-3/8

(273) (251) (235) (216) (203) (187)

130°150°
6-1/4 (159) 6-3/4 (171) 6-7/8 (175)

150°180°
5-1/4 (133) 5-3/4 (146) 5-7/8 (149)

Narrow Frame Mount
2 to 2-3/4 (51 to 70)

1-1/2

Soffit Plate

(38)

890 Bracket

7/16

NOTE: For Blade Stop Mounting only.

(11) 1

Prepare 2 holes for 6890 bracket after installing 6891 block. The 1″ dimension

(25) is from the bottom of the 6891 block.

3/4 2-1/2 (19)
(64)

1-1/4 (31.8)

5/8 Ref. (16)

Blade Stop Mount
2 to 2-3/4 (51 to 70)

2-3/8 (60)

A

6-3/4 (172)

Flush Partition
C
CLHinge or Pivot

1/2 (13)
1-1/2 (38)

Soffit Plate 890 Bracket

891 Block

2-1/2
(64) 3/4 (19)

1-3/4 (44)

293L Angle Bracket

Soffit Plate

2-1/2 (64)

Page 4

2-3/8 (60)
A

6-3/4 (172)

80-9344-2205-010 (09-11)

488 Drop Plate Mounting Holes

Standard Frame
CLHinge or Pivot

4 (102)

4-3/4 (121)

D

1 (25)
4 (102)
5/16 (8)

Notes: Left Hand Door Shown. Same dimensions apply for Right Hand Door measured from centerline of pivot point. Dimensions are in inches (mm). See Chart below for A dimension values.
488 Drop Plate

Narrow Frame

CLHinge or Pivot D

4 (102)

4-3/4 (121)

4 (102)

1 (25)
5/16 (8)

890 Bracket 488 Drop Plate

Flush Partition
D

4 (102)

4-3/4 (121)

1 (25)
4 (102)
5/16 (8)

CLHinge or Pivot

293L Bracket 488 Drop Plate

Installation Dimensions Chart

Dim Up to 90° 90°-95° 95°-100° 100° to 105° 105°-110° 110°-115° 115°-130° 130°-150° 150°-180°

PR4400/

PR4410/ PR40X/ PR140X
4020/

D
inch (mm)

8-1/2 (216)

7 (178)

4420/ 402X/

9-7/8 (251) 9 (229) 8-3/8 (213) 7-5/8 (194) 7-1/8 (181) 6-1/2 (165)

442X

6 (152) 5 (127)

80-9344-2205-010 (09-11)

Page 5

Unit Adjustment
Closing Speed Controls (Figure 2A or 2B and 3.) · Valve “S/D” Controls Sweep Range on Standard closer
(or Delayed Range on Delayed Action closer). · Valve “L” Controls Latch Range. · Valve “S” Controls Sweep only on Delayed Action closer.

Closing Power Control

Figure 1.

Adjust as required (see Power Adjustment Chart on page 3).

Install closer per instructions with the proper pre-load applied to the arm then adjust spring power. The power adjustment will not work properly if the closer spring is not pre-loaded.
+ Increase Power

Opening Door Control (Figure 4.)
· Backcheck (“B”) valve controls the hydraulic resistance to door opening. NEVER close this valve completely ­ it is not to provide a positive stop.

· Backcheck position (“P”) valve controls the door angle where backcheck cushioning starts. Valve normally closed.

Opening Door Control

Figure 4.

BACKCHECK
NG

LATCH LATCH
OPENI

wrench

-Decrease Power

11/16″ Power Adjustment-Nut

Opening Cycle

DO NOT use a power drill or driver to turn adjustment nut. This will damage closer and void warranty.

Closing Speed Controls

Figure 2.

SWEEP

DELAY RANG

E

10°

SWE

EP

70°

10°

CLOSED

CLOSED

Standard Closing Cycle 2A

Delayed Action Closing Cycle
2B

Adjust Closing Speed Time to between 3 to 7 second from 90°. Use of the door by handicapped, elderly or small childen may require greater closing time.

Backcheck Control

Backcheck Position

Open for backcheck later in door-opening cycle.

“P”

1/8″ Hex

Normally

Key Closed

Do not force valves counter-clockwise out of closer body or a fluid leak will occur.

Figure 5.

Backcheck Cushion

“B” (NEVER Close Completely)

Increase
1/8″ Hex Key

Decrease

Identify Door Closer

Standard 7570/7770 = 4 valves (S/D, L, P&B)

Delayed Action 7570DA/7770DA = 5 valves (S/D,S,L, P&B)

B

P

S/D S

S/D S

LDIOSTOERDC1L4O9SAERR66B8ORD7Y85

Closing Speed Controls
“L” (Latch) “S/D” (Sweep)

Figure 3.
“L” (Latch) “S” “S/D” (Delayed Action)

Standard Closer
Do not force valves counter-clockwise out of closer body or a fluid leak will occur.

Delayed Action Closer

Slow 1/8″ Hex Key Fast

All Valves

4
7700 Series Body = size “2, 3, 4, 5 or 6” (Stamped Single digit)

7500 Series Body = size “1-6” (No Stamp)

Hold Open Option
The Hold-Open feature is controlled by the knob located on the arm of the unit. Turning this knob clockwise will engage the Hold-Open mechanism and increase the Hold-Open force. Turning this knob counterclockwise will reduce the Hold-Open force and disengage the Hold-Open mechanism.

DECREASE – – INCREASE
Thumbturn Action (Units suffixed “T”)

Yale ® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2003, 2011, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

Page 6

80-9344-2205-010 (09-11)

An ASSA ABLOY Group brand
3000 Highway 74 East · Monroe, NC 28112 Tel: (800)-438-1951 · Fax: (800)-338-0965
www.yalelocks.com

References

• Welcome to Yale - Trusted every day. | Yale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>