VIVO STAND-3DRH Clamp on Reel Holder for 3D Printer Instruction Manual
- June 17, 2024
- Vivo
Table of Contents
VIVO STAND-3DRH Clamp on Reel Holder for 3D Printer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
-
A (x1)
Arm Set
-
B (x1)
Lower Pole
-
C (x1)
Upper Pole -
D (x1)
Pole Cap -
E (x1)
Pole Collar -
F (x2)
End Plate -
G (x1)
Clamp -
S-A (x2)
M10
Thumbscrew -
S-B (x3)
M6x16mm Screw -
T-A (x1)
3mm Allen Wrench -
T-B (x1)
6mm Allen Wrench -
T-C (x1)
5mm Allen Wrench
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
- Phillips Screwdriver
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosen clamp knob on Clamp (G). Ensure the screws on the back of Clamp (G) are tight using 5mm Allen Wrench (T-C).
Install Lower Pole (B) to Clamp (G) using M6x16mm Screws (S-B) and 3mm Allen Wrench (T-A). Attach Clamp (G) to desktop.
Identifying Lower Pole:
Lower Pole (B) has external threading at the end of the pole.
STEP 2
Thread Arm Set (A) together, twisting until connection is tight. Thread Upper Pole (C) onto Lower Pole (B).
Slide Pole Collar (E) towards the center arms and tighten using 6mm Allen Wrench (T-B).
Install End Plates (F) to outer edges of arms using Thumbscrews (S-A).
STEP 3
Thread Upper Pole (C) onto Lower Pole (B).
STEP 4
Slide Pole Collar (E) onto Upper Pole (C). Find desired height position and lock into place using 6mm Allen Wrench (T-B). Install Pole Cap (D) onto the top of Upper Pole (C).
HEIGHT ADJUSTMENT
To adjust height of arms, loosen bolt on Pole Collar (E) using 6mm Allen Wrench (T-B). Find desired height position and lock into place using 6mm Allen Wrench again.
Customer Support
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
SKU: STAND-3DRH
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. Instruction Manual https://vivo- us.com/products/stand-3drh
GET IN TOUCH | Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15
M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT : www.vivo- us.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>