HUDSON VALLEY 3917-AGB Hingham Two Light Wall Sconce Instruction Manual
- June 17, 2024
- HUDSON VALLEY
Table of Contents
Hudson Valley Lighting / Troy Lighting /
Mitzi / Corbett Lighting
3917-AGB Hingham Two Light Wall Sconce
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION ANDMAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANYDAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
| PART(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B,C,D | HARDWARE KIT | HDW-02 |
| E | FIXTURE MOUNTING SCREW | SCR-M |
| K | GLASS | GLS-3917 |
FIXTURE INSTALLATION
-
Attach the MOUNTING PLATE (A) unto the junction box using the MOUNTING SCREWS (B). Thisfixture is designed to be mounted on standard round or octagon junction box. The junction box mustbe securely mounted to the structure of the building.
-
Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copperwire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE
TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH! -
Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wirestogether with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURETHERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
-
Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joinedwires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOWTHIS COULD RESULT IN SERIOUS INJURY OR DEATH!
-
Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the FIXTUREMOUTING SCREWS (E).
-
Screw the BULB (J) into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR MAX 15 WATT TYPE ALAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE
-
Tilt and rotate the GLASS (K) so that the GLASS HOLDER (I) into GLASS (K). drop GLASS FITTER (H)and secure with the RING (G).
-
Put GLASS (K) into the RING (L) of the fixture.
-
Restore power to the outlet at the breaker or fuse box.
Documents / Resources
|
HUDSON VALLEY 3917-AGB Hingham Two Light Wall
Sconce
[pdf] Instruction Manual
3917-AGB Hingham Two Light Wall Sconce, 3917-AGB, Hingham Two Light Wall
Sconce, Two Light Wall Sconce, Light Wall Sconce, Wall Sconce, Sconce
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>