HUDSON VALLEY 2913-AGB Tournu LED Lantern Instruction Manual
- June 17, 2024
- HUDSON VALLEY
Table of Contents
Hudson Valley Lighting / Troy Lighting / Mitzi / Corbett Lighting
TOURNU2913
Installation Instructions
2913-AGB Tournu LED Lantern
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION ANDMAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANYDAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
| PART(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B,C,D,E | HARDWARE KIT | HDW-04 |
| F | STEM KIT | STM-LT1600-SET |
| G | CANOPY | CPY-2913 |
| H | ALLEN KEY | TOL-2913 |
| 1 | CHAIN | CHN-CN1031-SET |
| L | DRIVER | DVR-2913 |
FIXTURE INSTALLATION
-
Open the end link on the CHAIN (J) and attach to the loop on the CAGE (K) (WITH LED). Hang CAGE(K) (WITH LED) on the CHAIN (J) at your desired height, and remove excess CHAIN (J).
-
Feed the wire through the CHAIN (J) and LOOP (I).
-
Open the top link on the CHAIN (J), and Hang the CAGE (K) (WITH LED) to the LOOP (I).
-
Feed the wire through the STEM KIT (F) and twist tightly onto the LOOP (I). Keep adding additionalstems until you desired hanging height is met.
-
Slide in CANOPY (G) onto the STEM KIT (F), and thread the 1/4 NIPPLE (E) onto the top end of theSTEM KIT (F)
-
Cut off excess wire, and strip the insulation off the end of the leads.
-
Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). Thisfixture is designed to be mounted on heavy duty round or octagon junction box rated for minimum 90lbs. The junction box must be securely mounted to the structure of the building.
-
Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bar copperwire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE
TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH -
Connect the fixture lead the ridge(s) to the neutral (Generally white) wire in the outlet box. Fasten thewires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURETHERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT
-
Connect the smooth fixture leads with to the hot (Generally black) wire in the junction box. Fasten thejoined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TOFOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
-
Push the wires and DRIVER (L) back into the CANOPY (G).
-
Lift up the CANOPY (G) up to the ceiling, and secure with the HEADLESS SCREW by using supplied ALLEN KEY(H).
-
Restore power to the outlet at the breaker or fuse box.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>