HUDSON VALLEY 3346-VGL Montclair Six Light Chandelier Instruction Manual

: June 17, 2024
: HUDSON VALLEY

Table of Contents

HUDSON VALLEY 3346-VGL Montclair Six Light Chandelier
Installation Instructions
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

HUDSON VALLEY 3346-VGL Montclair Six Light Chandelier

HUDSON-VALLEY-3346-VGL-Montclair-Six-Light-Chandelier-
PRODUCT

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.
THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN.
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.
WASH HANDS AFTER USE. · UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND.
INSPECT THE FIXTURE BEFORE INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES.
FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

Installation Instructions

HUDSON-VALLEY-3346-VGL-Montclair-Six-Light-Chandelier-
FIG-1

PART(S)	REPLACEMENT PART NAME	NUMBER
A, B,C, D,E, F,G	HARDWARE KIT	HDS-04
H,I, J	CANOPY ASSEMBLY	CAS-3346
K	CHAIN	CHN-3345
N	LOOP	LFH-3345
O	GLASS ASSEMBLY	GAS-3341
P	SOCKET RING	RNG-E12
Q	CANDLE SLEEVE	CDL-3341

FIXTURE INSTALLATION

Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
Remove the SCREW COLLAR (I) from the COLLAR LOOP (H). Fully thread the NIPPLE (C) onto the COLLAR LOOP (H). Thread the HEX NUT (E) onto the NIPPLE (C) along with the TOOTH WASHER (D). Then thread the NIPPLE (C) onto the MOUNTING PLATE (A). Adjust the NIPPLE (C) so that the threads of the COLLAR LOOP (H) extend 1″ beyond the CANOPY (J). Secure using HEX NUT (E).
Feed the wires through the LOOP (N). Twist the LOOP (N) tightly onto the exposed thread of the FIXTURE ASSEMBLY (L).
Open the end link of the CHAIN (K) and attach it to the LOOP (N) at the desired height. Slide the SCREW COLLAR (I) and the CANOPY (J) onto the CHAIN (K). Open the link on the other end of the CHAIN (K) then attach it to the COLLAR LOOP (H). Feed the wires through the CHAIN (K), SCREW COLLAR (I), CANOPY (J), COLLAR LOOP (H), NIPPLE (C), and MOUNTING PLATE (A).
Cut off excess wires, and strip the insulation off the end of the leads.
Attach the Ground wire to the ground inside the junction box (Generally green or bare copper wire) or the GROUND SCREW (F) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO
“HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Connect the fixture’s SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (G). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OR STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
Connect the fixture’s SPT hot (SPT WITH WRITINGS) wire lead to the hot (Generally black) wire in the junction box. Fasten the joined wires the same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Push the wires back into the junction box. Lift the CANOPY (J) to the ceiling, and screw the SCREW COLLAR (I) onto the COLLAR LOOP (H).
Place the GLASS (O) and the CANDLE SLEEVE (Q) onto the SOCKET of the FIXTURE ASSEMBLY (L) and secure using the SOCKET RING (P).
Screw the BULB (M) up into the SOCKET of the FIXTURE ASSEMBLY (L). THIS FIXTURE IS RATED FOR 8 8-WATT TYPE G LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
Restore power to the OUTLET at the breaker or fuse box.

www.hvlgroup.com

Documents / Resources

| HUDSON VALLEY 3346-VGL Montclair Six Light Chandelier [pdf] Instruction Manual
3346-VGL Montclair Six Light Chandelier, 3346-VGL, Montclair Six Light Chandelier, Six Light Chandelier, Light Chandelier, Chandelier
---|---