HUDSON VALLEY 1117-OB Granby Pendant Ceiling Light Instruction Manual

: June 17, 2024
: HUDSON VALLEY

Table of Contents

Installation Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HUDSON VALLEY 1117-OB Granby Pendant Ceiling Light Instruction Manual

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

Installation Instructions

Feed the WIRE (K) of the FIXTURE ASSEMBLY (L) through the SCREW COLLAR (I), CANOPY (G), NIPPLE (E), MOUNTING PLATE (A), and STRAIN RELIEF WASHER (F) until you desired hanging height is met
Tie an overhand knot to secure the wire in place above the NIPPLE (E). Trim off excess wire minimum 6 beyond the knot and Strip each wire end 5/8″
Attach the MOUNTING PLATE (A) to the Junction box using the MOUNTING SCREWS (B). This fixture Is designed to be mounted to a standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
Screw the BULB (N) up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR MAX 25 WATT TYPE A LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
Put the GLASS (O) into the RING (M) of the fixture.
Open the end link on the CHAIN (I) and attach to the loop on the RING (M). Hang the RING (M) on the CHAIN (I) at your desired height, and remove excess CHAIN (1).
Feed the wire through the CHAIN (H), LOOP (H), CANOPY (G) and MOUNTING PLATE (A).
Open the top link on the CHAIN (H), and Hang the RING (M) to the LOOP (H).
Cut off excess wire, and strip the insulation off the end of the leads.
Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO ‘HOT’ WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
II. Connect the fixture lead the ridge(s) to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting I’ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
Connect the smooth fixture leads with to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Push the wires back into the junction box. Lift up the CANOPY (G) up to the ceiling, and secure the SCREW COLLAR (I) onto the NIPPLE (E).
Restore power to the outlet at the breaker or fuse box.