HUDSON VALLEY 7828-AGB LED Semi Flush Mount Light Holmdel Instruction Manual
- June 17, 2024
- HUDSON VALLEY
Table of Contents
HUDSON VALLEY 7828-AGB LED Semi Flush Mount Light Holmdel
WARNING/CAUTION
DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL
INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. · TO AVOID THE RISK OF
FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE
NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN. · CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE. · UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE
FOUND. INSPECT THE FIXTURE BEFORE INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS. · PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
FIXTURE INSTALLATION
-
Determine the location of the lamp. Using the mounting plate as a template, mark the location of the holes for the WALL ANCHOR (F).
-
Drill the appropriate size holes for the WALL ANCHOR (F). (the holes should be slightly smaller than the size of the anchors.) Install the wall anchors to the hole.
-
Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a standard junction box. The junction box must be securely mounted to the structure of the building. Screw in the WOOD SCREW (E) to the WALL ANCHOR (F).
-
Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
-
Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting I’ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
-
Connect the black fixture to the hot (Generally black) wire in the junction box. Fasten the joined wires the same as in the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
-
Push the wires and drive (O) back into the FIXTURE ASSEMBLY (1) (WITH LED).
-
Attach the FIXTURE ASSEMBLY (1) (WITH LED) to the MOUNTING PLATE (A) and secure with the NUT (G) and CAP NUT (H).
-
Attach the ACRYLIC (J), ALABASTER A,B (M,N) ( PLACE ACCORDING TO THE ALABASTER CORNER
MARKS IN THE FRONT VIEW) and SILICONE WASHER (K) and secure with the FINIAL (L). -
Restore power to the outlet at the breaker or fuse box.
| PART(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B,C,D,E,F | HARDWARE KIT | HDW-7828 |
| G | NUT | NUT-7828 |
| H | CAP NUT | CPN-7828 |
| J | ACRYLIC | ACR-7803 |
| K | SILICONE WASHER | WAR-7803 |
| L | FINIAL | FIN-7803 |
| M | ALABASTER A | ALA-7803-A |
| N | ALABASTER B | ALA-7803-B |
| O | DRIVER | DVR-7828 |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>