HUDSON VALLEY 5616 Montreal One Light Wall Sconce Instruction Manual

June 17, 2024
HUDSON VALLEY

**HUDSON VALLEY 5616 Montreal One Light Wall Sconce Instruction Manual

**

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. ·

TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN. · CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE. ·

UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS. ·
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

Installation Instructions

PART(S) REPLACEMENT PART NAME NUMBER
A,B,C,D HARDWARE KIT HDW-02
E FIXTURE MOUNTING SCREW SCR-M
G NIPPLE NIP-5616
H STONE STN-5616
I FINIAL FIN-5616
K SHADE SHD-5616

FIXTURE INSTALLATION

  1. Attach the MOUNTING PLATE (A) unto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
  2. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copperware) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEER CONNECT GROUND WIRETO “HOT” WIREĞ FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATHĞ3.
  3. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wirestogether with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap theconnection with electrical tape so that the connections seals the end of the fastener. MAKE SURETHERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUITĞ4.
  4. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joinedwires same as previous step. NEER REERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOWTHIS COULD RESULT IN SERIOUS INJURY OR DEATHĞ
  5. Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the FIXTUREMOUNTING SCREWS (E).
  6. Screw the NIPPLE (G) into the FIXTURE ASSEMBLY (F) of the fixture.
  7. Attach the STONE (H) to the FIXTURE ASSEMBLY (F) and secure with the FINIAL (I).
  8. Screw the BULB (J) into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR MAX 8 WATT TYPE BLAMP. DO NOT EXCEED THE RECOMMENDED WATTAGEĞ
  9. Place the SHADE (K) over the BULB (J) of the fixture.
  10. Restore power to the outlet at the breaker or fuse box.

www.hvlgroup.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HUDSON VALLEY User Manuals

Related Manuals