HUDSON VALLEY 8136 Wingate LED Chandelier Instruction Manual
- June 17, 2024
- HUDSON VALLEY
Table of Contents
HUDSON VALLEY 8136 Wingate LED Chandelier
FAQ
- What should I do before starting the fixture installation?
- Before starting the installation, disconnect the power and read all instructions completely. Ensure the fixture is installed in compliance with all applicable national and local electrical/building codes.
- What is California Proposition 65 warning about?
- The lighting fixture contains chemicals known to the state of California to cause cancer, birth defects, and/or other reproductive harm. It is recommended to wash hands after handling the fixture.
- Can the fixture be returned once installed?
- No, once the fixture has been installed, it cannot be returned. Check for all parts and inspect for any damage before installation.
- How should I clean the fixture?
- The fixture should be cleaned with a soft, dry cloth only. Do not use any cleaners.
For more information, please visit www.hvlgroup.com
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE BEFORE INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
WINGATE 8136
Installation Instructions
| PART(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B, C,D | HARDWARE KIT | HDW-8136 |
| E | CAP NUT | CPN-8136 |
| F, G | CANOPY ASSEMBLY | CAS-8136 |
| H | PLATE | PLA-8136 |
| I | FINIAL | FIN-8136 |
| J | CHAIN | CHN-8136 |
| L | ALABASTER | ALA-8136 |
| M | STUD | STD-8136 |
| N | DRIVER | DVR-8136 |
FIXTURE INSTALLATION
- Open the end link on the CHAIN (J) and attach it to the loop on the FIXTURE ASSEMBLY (K) (WITH LED). Hang the FIXTURE ASSEMBLY (K) (WITH LED) on the CHAIN (J) at your desired height, and remove excess CHAIN (J).
- Feed the wire through the CHAIN (J), LOOP (G), CANOPY (F) and MOUNTING PLATE (A).
- Open the top link on the CHAIN (J), and Hang the FIXTURE ASSEMBLY (K) (WITH LED) to the LOOP(I).
- Insert the male connector from the fixture into the female connector from DRIVER (N), then hide the excess wires and DRIVER (N) in the junction box.
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
- Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRES OR STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT.
- Connect the black fixture to the hot (Generally black) wire in the junction box. Fasten the joined wires the same as in the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
- Push the wires back into the junction box. Lift the CANOPY (F) to the ceiling and secure with CAP NUTS (E), and attach PLATE (H) onto the CANOPY (F) and secure with FINIAL (I).
- Attach the ALABASTER (L) to the FIXTURE ASSEMBLY (K) (WITH LED) and secure with the STUDS (M).
- Restore power to the outlet at the breaker or fuse box.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>