RANGER N5-DS84-4 Shelving Installation Guide

June 4, 2024
RANGER

RANGER Logo N5-DS84-4 Shelving
Installation Guide
RANGER N5-DS84-4 Shelving

Transit High Roof & Medium Roof
Promaster Standard Roof & High Roof
Nissan NV High Roof
Sprinter Low Roof & High Roof
Box Truck / Trailer

REQUIRED ITEMS

2 PERSONS| • Cordless Impact
• Cordless Drill
• Tape Measure
• Marker
• 1/2″ Socket
• 1/2″ Drill Bit w/ Drill Collar ( Set at 1/2″ )
• 3/8″ Driver Bit
• Knife
• Plusnut Tool / Plusnut Gun ( 5/16″ )
---|---

PHASE 1 – ASSEMBLY

1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.

RANGER N5-DS84-4 Shelving - 1.1 SETUP1.1.2 Verify all parts are present.

BILL OF MATERIALS

Item No. Description Qty.
40 – 704 Center Post 1
40 – 707 Short Corner Bracket   ( Left ) 1
40 – 708 Short Corner Bracket   ( Right ) 1
40 – 709 Long Corner Bracket   ( Left ) 1
40 – 710 Long Corner Bracket   ( Right ) 1
40 – 7002 End Panel   ( Left ) 1
40 – 7003 End Panel   ( Right ) 1
60 – 15.875 × 84 Shelf Tray, Black Plywood, Usable 16″ × 84″ 1
60 – 17.875 × 84 Shelf Tray, Black Plywood, Usable 18″ × 84″ 3
94 – 4026 Assembly Fastener Kit 1
96 – 4026 Install Fastener Kit 1

1.1.3Fastener kits.

94 – 4026 Fastener Kit

8×| | # 90-204| Hex Bolt
5/16″-18 × 3/4″
GR-5 ZINC
---|---|---|---
8×| | # 92-200| Screw HFH

10 – 16 × 3/4″

ZINC
32×| | # 92-102| Screw HWH

14 × 1″

ZINC
8×| | # 94-116| Serrated Nut
5/16″-18
ZINC
8×| | # 98-116| Flat Washer
5/16″ – 18 × 1″
ZINC
6×| | # 90-011| Hex Bolt
5/16″-18 × 1-3/4″
GR-5 ZINC
8×| | # 90-212| Hex Bolt
5/16″-18 × 1-1/4″
GR-5 ZINC
14×| | # 94-132| Plusnet
14×| | # 98-116| Flat Washer
5/16″, O.D. 7/8″
ZINC
14×| | # 98-122| Lock Washer
5/16″
ZINC
6×| | # 98-157| Spacer
0.375″ ID, × 1.0″ OD × 0.25″ LONG
NYLON

Fastener Assembly

| #90-204 Hex Bolt    5/16″ × 3/4″
---|---
| #98-116 Flat Washer
| #94-116 Serrated Nut

| #92-200 Screw   #10 – 16 × 3/4″
---|---

32×

| #92-102 Screw   #14 × 1″
---|---
| #90-212 Hex Bolt 5/16″ × 1-1/4″
---|---

98-122 Lock Washer

98-116 Flat Washer

94-132 5/16″ Plusnut


| #90-011 Hex Bolt 5/16″ × 1-3/4″
---|---

98-122 Lock Washer

98-116 Flat Washer

98-157 Spacers

( QTY = Gap beTween floor and end panel )

94-132 5/16″ Plusnut

1.2 SHELF ASSEMBLY

1.2.1 Attach both panels to the shelf trays.
NOTE : You can adjust the bottom shelf location to maximize or minimize your space over the wheel.
IMPORTANT : Always handle panels on a smooth, protected, and clean surface to avoid unnecessary scratching.

RANGER N5-DS84-4 Shelving - Shelf tray position guide

RANGER N5-DS84-4 Shelving - Cordless Impact

1.2.2 Attach the center post to the center front face of the shelf.

RANGER N5-DS84-4 Shelving - center post NOTE : The bottom flange of the center post needs to be flush with the bottom of the end panel.

RANGER N5-DS84-4 Shelving - bottom flange

PHASE 2 – INSTALLATION

2.1 ATTACH WALL BRACKETS TO THE END PANELS

IMPORTANT: For all Box Trucks, make sure that the shelving is securely fastened to the structure of the truck.
2.1.1

  • Lift the assembled shelf to the vehicle, then put it in place.
  • Attach the short and long brackets to the panels aligning the brackets to the horizontal rim of the vehicle.
    NOTE : Handle with care.

RANGER N5-DS84-4 Shelving - Handle with care.

Attach the short and long brackets to the panels aligning the brackets to the horizontal rim of the vehicle.
NOTE: You can install the brackets inside or outside the panel.
TOOLS

  • Cordless Impact
  • 1/2″ Socket

HARDWARE USED
hand-tighten the bolts

RANGER N5-DS84-4 Shelving - HARDWARE USED

2.2 MARK HOLES FOR PLUS NUTS

2.2.1 After attaching the brackets mark the holes on the brackets, end panels, and center post to the vehicle.

NOTE : The distance between the two holes should be no less than 1″, to avoid plus nut overlap
RANGER N5-DS84-4 Shelving - distance betweenMark 2 holes of the short and long brackets on the vehicle’s horizontal rim.
NOTE: If you are using Ranger wall kits, please go to page 14.
TOOLS

  • Marker

RANGER N5-DS84-4 Shelving - distance between1

Mark 2 holes in each end panel and mark also the 2 holes of the center post on the vehicle floor.
NOTE : If you are using the Ranger floor, please go to page 12.
TOOLS

  • Marker

RANGER N5-DS84-4 Shelving - MARK

2.3 ATTACH PLUS NUTS
2.3.1 • Lift the assembled shelf on the side.

  • Drill all the marks using a 1/2″ drill bit w/ drill collar, then attach plus nuts to the holes.
    NOTE : Use a 1/2″ drill bit with a drill collar to stop the drill at 1/2″ depth.
    WARNING : Before drilling, ensure that you will not hit any critical parts of the vehicle like the Gas tank, Wiring Harness, and Hose.

RANGER N5-DS84-4 Shelving - plus nuts

2.3.2 How to attach plus nut.

  • using plus nut gun
    STEP : Put the plus nut on the Plusnet gun, then attach the plus nut in the hole by turning the gun forward until the plus nut locks, then remove the gun by turning it in reverse.
    RANGER N5-DS84-4 Shelving - using plusnut gun

  • using the 6491 plus nut tool
    NOTE : The hardware used for the 6490 plus nut tool is not included in the fastener bag.
    The 6490 plus nut tool can be ordered separately upon demand at no charge.

TOOLS

  • Cordless Impact
  • 1/2″ Socket
  • 9/16″ Wrench
6491 HARDWARE USED
Flat washer 5/16″

Flat washer 5/16″ BS × 7/8″ OD

STEP 1:
Assemble the 6491 plus nut tool with the hardware needed, plus the nut and the 9/16″ wrench as shown.


STEP 2:
Attach the plus nut in the hole by turning the bolt forward using an impact with a 1/2″ socket until the plus nut locks, then remove the bolt by turning the impact in reverse.

2.4 ATTACH SHELF UNIT TO THE FLOOR

without ranger floor

2.4.1 Put the assembled shelf back in place aligning the holes to the plus nuts, then install the end panels and center post to the plus nuts.

RANGER N5-DS84-4 Shelving - without ranger floor

TOOLS

  • Cordless Impact
  • 1/2″ Socket

HARDWARE USED

RANGER N5-DS84-4 Shelving - 6X

most vehicle use 1 spacer when not over ribs
note : The fastener should always be installed as close to the vertical face as possible.

RANGER N5-DS84-4 Shelving - without ranger floor2

with ranger floor

2.4.2 • Lift the shelving unit inside the van, then put it in place.

  • Install the shelving unit to the floor mounting track by sliding bolts in the mounting tracks, and putting a screw in the last rear slot of the end panels of the shelving unit.
    RANGER N5-DS84-4 Shelving - with ranger floor

RANGER N5-DS84-4 Shelving - STEEL

2.5 ATTACH WALL BRACKETS

without ranger wall kits

2.5.1 Aligned the wall brackets to the plus nuts, then install the wall brackets to the wall.
NOTE : Tightened the bolts that are used to attach the wall bracket to the wall or wall kits 1 st before the bolts that are used to attach the wall bracket to the end panel.
IMPORTANT : After installation is completed, ensure all bolts are tightened.

RANGER N5-DS84-4 Shelving - with ranger wall kits6RANGER N5-DS84-4 Shelving - without ranger wall
kits2

with ranger wall kits

2.5.2 Aligned the wall brackets to the wall mounting track kits, then install the wall brackets to the wall mounting track kits using channel nuts.
NOTE : Tightened the bolts that are used to attach the wall bracket to the wall or wall kits 1 st before the bolts that are used to attach the wall bracket to the end panel.
IMPORTANT : After installation is completed, ensure all bolts are tightened.

RANGER N5-DS84-4 Shelving - without ranger wall kitsRANGER N5-DS84-4 Shelving - FUSD

RANGER N5-DS84-4 Shelving-

RANGER Logo

“You have successfully installed your
N5-DS84-4
Thank you for doing business with us.”
For any feedback or suggestions, you may have, please contact:cs@rangerdesign.com
For technical support, contact us at 1-800-565-5321
N5-DS84-4 Installation Guide | REV. B1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals