RANGER DESIGN N5-DS36-4 Shelving Unit Installation Guide

October 27, 2023
RANGER DESIGN

RANGER-logo

RANGER DESIGN N5-DS36-4 Shelving Unit

REQUIRED ITEMS

  • Cordless Impact
  • Cordless Drill
  • Tape Measure
  • Marker
  • 1/2″ Socket
  • 1/2″ Step Bit
  • 3/8″ Driver Bit
  • Knife
  • Plusnut Tool / Plusnut Gun ( 5/16″ )

ASSEMBLY

Unpack components; compare with the bill of materials.RANGER-
DESIGN-N5-DS36-4-Shelving-Unit-fig-2

Verify all parts are present

BILL OF MATERIALS

Item No. Description Qty.
40 – 707 Short Corner Bracket  ( Left ) 1
40 – 708 Short Corner Bracket  ( Right ) 1
40 – 709 Long Corner Bracket  ( Left ) 1
40 – 710 Long Corner Bracket  ( Right ) 1
40 – 7002 End Panel ( Left ) 1
40 – 7003 End Panel ( Right ) 1
60 – 15.875 × 36 Shelf Tray, Black Plywood, Usable 16″ × 36″ 1
60 – 17.875 × 36 Shelf Tray, Black Plywood, Usable 18″ × 36″ 3
94 – 4025 Assembly Fastener Kit 1
96 – 4025 Install Fastener Kit 1

Fastener kits.RANGER-DESIGN-N5-DS36-4-Shelving-Unit-
fig-6

ASSEMBLY

SHELF ASSEMBLY
Attach both panels to the shelf trays.
NOTE: You can adjust the bottom shelf location to maximize or minimize your space over the wheel.
IMPORTANT: Always handle panels on a smooth, protected and clean surface to avoid unnecessary scratching.RANGER-DESIGN-N5-DS36-4-Shelving-Unit-
fig-9RANGER-DESIGN-N5-DS36-4-Shelving-Unit-
fig-10 ATTACH WALL BRACKETS TO THE END PANELS
IMPORTANT: For all Box Trucks, make sure that the shelving is securely fastened to the structure of the truck.

  • Lift the assembled shelf to the vehicle, then put it in place.
  • Attach the short and long brackets to the panels aligning the brackets to the horizontal rim of the vehicle.
  • NOTE : Handle with care.RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-11RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-12

ATTACH PLUS NUTS
WARNING: Before drilling, ensure that you will not hit any critical parts of the vehicle like the Gas tank,
Wiring Harness and Hose.
NOTE: Use 1/2″ drill bit with drill collar to stop drill at 1/2″ depth.

  • Lift the assembled shelf on the side.
  • Drill all the marks using 1/2″ drill bit w/ drill collar, then attach plus nuts to the holes

RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-16

How to attach plus nut

using plusnut gun

STEP: Put the plusnut on the plusnut gun, then attach the plus nut in the hole by turning the gun forward until the plus nut locks, then remove the gun by turning in reverse.

using the 6491 plusnut tool

NOTE: The hardware used for the 6490 plusnut tool is not included in the fastener bag.
The 6490 plusnut tool can be ordered separately upon demand at no charge RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-18RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-19

ATTACH SHELF UNIT TO THE FLOOR

without ranger floor

Put the assembled shelf back in place aligning the holes to the plusnuts, then install the end panels to the plus nuts.RANGER-DESIGRANGER-DESIGN-N5-DS36-4
-Shelving-Unit-fig-21N-N5-DS36-4-Shelving-Unit-fig-20RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-22RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-23

with ranger floor

  • Lift the shelving unit inside the van, then put it in place.
  • Install the shelving unit to the floor mounting track by sliding bolts in the mounting tracks, and putting screw in the last rear slot of the end panels of the shelving unitRANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-24 RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-25

ATTACH WALL BRACKETS

without ranger wall kits

Aligned the wall brackets to the plus nuts, then install the wall brackets to the wall.

NOTE: Tightened the bolts that used to attached the wall bracket to the wall or wall kits 1st before the bolts that used to attached the wall bracket to the end panel.

IMPORTANT: After installation is completed, ensure all bolts are tightenedRANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-26 RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-27

with ranger wall kits

Aligned the wall brackets to the wall mounting track kits, then install the wall brackets to the wall mounting track kits using channel nuts.
IMPORTANT: After installation is completed, ensure all bolts are tightened.
NOTE: Tightened the bolts that used to attached the wall bracket to the wall or wall kits 1st before the bolts that used to attached the wall bracket to the end panelRANGER-DESIGN-N5-DS36-4-Shelving-Unit-
fig-28 RANGER-DESIGN-N5-DS36-4-Shelving-
Unit-fig-29

RANGER-DESIGN-N5-DS36-4-Shelving-Unit-fig-30

“You have successfully installed your
N5-DS36-4
Thank you for doing business with us.”

For any feedback or suggestions you may have, please contact: cs@rangerdesign.com

For technical support, contact us at 1-800-565-5321

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

RANGER DESIGN User Manuals

Related Manuals