DELVCAM DELV-7XLPRO-ATSC LCD Monitor User Guide

June 17, 2024
Delvcam

DELVCAM logo

Delvcam
DELV-7XLPRO-ATSC
User Guide

DELVCAM DELV-7XLPRO-ATSC LCD Monitor

DELV-7XLPRO-ATSC LCD Monitor

Dear Customer
Thank you for purchasing our ATSC TV receiver. It can receive ATSC digital TV signal, also receive the common analog TV by the antenna or CATV cable. And with the audio and video output interface, it could be the current received signal output. To ensure the best use of the unit, please read this manual carefully beforehand.

Notice

  1. Do not open the unit or remove the rear panel of this product. lf in need of service, please call a qualified service technician.
  2. To prevent unexpected thing happened, don’t let children insert something into the unit.
  3. Don’t expose this product to direct sunlight, heat or humid conditions.
  4. Keep away from strong light while using this product so as to obtain the clearest and the most colorful picture.
  5. Avoid heavy impact or drop onto the ground.
  6. Do not use chemical material to clean this unit, please simply wipe it with a clean soft cloth to keep the brightness of the surface.

If you do not want to use this product for a long time, or during a thunderstorm, break the power cord and the antenna as a safety precaution.

 Introduction

1. Panel Description

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - Panel

  1. External antenna of screw thread port

  2. Power on/off

  3. ATSC/NTSC(TV)/AV switch

  4. lRSENSORS

  5. Volume increase; adjust the value of item in the image menu; adjust the value of item or enter the submenu in ATSC main menu

  6. CH+: Channel selection (ATSC/NTSC(TV)) or select function upwards in the menu

  7. CH-: Channel selection (ATSC/NTSC(TV)) or select function downwards in the menu

  8. MENU: Menu key
    Press this key to display the image menu in NTSC(TV)/AV state.
    In ATSC state, short press this key to display ATSC main menu, then shon press again to exit main menu; When enter the submenu, press this key to return the main menu. Long press this key to display the image menu, and then press this key to enter the next menu item until exit the menu.

  9. Volume decrease; adjust the value of item in the image menu; adjust the value of item or enter the submenu in ATSC main menu

  10. EAR.: Earphone jack

  11. NV UN: AN1 input jack

  12. AN2.IN:AN2 inputjack

  13. AN.OUT: AN output jack

  14. DC l2V power input jack

2. Remote Controller

  1. : Power on/off
  2. : MUTE. During working press this key to eliminate the voice for a while, press again to restore the original volume.
  3. : Volume down or adjust the value of setting function in the image menu; adjust the vaiue of item or enter the submenu in ATSC main menu
  4. : Select item on menu or to increase channel in ATSC/NTSC(TV)
  5. OK: Channel confirmed key in ATSC
  6. : Select item on menu or to decrease channel in ATSC/NTSC(TV)
  7. : Volume up or adjust the value of setting function in the image menu; adjust the value of item or enter the submenu in ATSC main menu
  8. MENU 1: Display the image menu
  9. EXIT: To exit menu
  10. MENU2: Display the ATSC main menu in ATSC, press it once more to exit; In the submenu press this key return to the main menu.
  11. FAV: Display “Favorite List” in ATSC mode
  12. INFO: Display the relevant information of current channel in ATSC
  13. RETURN: Return to last program in ATSC mode
  14.  TV/AV: SwitchATSC, NTSC(TV),
  15. SOUND: Adjust the audio language in ATSC
  16.  GITTO: Display the program guide in ATSC
  17.  CC/ON: Open or close the caption in ATSC
  18. CIA: Switch the searching source type (Cable, Antenna) in ATSC
  19. 0-9: Number keys
  20. FORMAT: Switch the display mode of image in ATSC.
  21. PROO: Display the program list in ATSC

Connection

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - Connection

After connecting the power indicator light will be red, press “POW” on the unit on the remote controller) to open, the memory function will keep the unit in the mode be selected last time after switched off.
1. ATSC
(1) ATSC main menu
Press “AVrrY” on the unit or “TV/AV” on the remote controller to switch ATSC state.
Press “tv1ENU” on the unit or “MENU2” on the remote controller lo display ATSC main menu, as follows the picture:

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device 1

Press “CH-“/ ”CH+” on the unit or ” / “ ” on the remote controller to select needful setup item, then press “V+” / “V-” on the unit or “ ” /” ” on the remote controller to enter the next submenu. Press “V+” / “V-” on the unit or “ ” /” ” on the remote controller to adjust the value of item or enter the submenu.

Auto Search:

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device 2

Source Type: Select the source type option list between ‘Cable’ and ‘Antenna’ Start Search: Start auto searching process
CH Setup: Channel setup

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device 3

Channel: Change the channel number
Skip: Switch the skip function of channel between ‘On’ and ‘Off’

CC Setup:

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device 4

CC Display: Select the CC display option list between ‘On’ and ‘Off’
608CC Type: Select the CC type option list
708CC Type: Select the CC type option list
CC Mode: Select the CC mode option list. When ‘CC Mode’ is Broadcast, ‘CC Customer’ is grayed-out and cannot be edited.
CC Customer: Enter the ‘CC Customer’ submenu

Parental Control:

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device 5 Press 0-9 number key to input the valid password and enter the ‘Parental Control’ menu. Note: the initial password is 8888.

System Setting:

DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device 6

Reset: Restore to the default setting
Time Setup: Set the ‘Clock’, ‘Time Zone’ and ‘Daylight Saving’
OSD Language: Select the OSD language
Audio Language: Select the audio language
Format: Select the display format of image

(2) Image menu
Long press “MENU” on the unit (“MENUI” on the remote controller) to display image menu, press “MENU” on the unit (“MENU1” on the remote controller) to select what you demanded items: Picture, Volume, Option, System, Clock, the item’s background will be yellow and press “CH-“or “CH+” on the unit / on the remote controller) to select what you demanded items, and the explanation of the item will display under the OSD menu. Use “V-“or “V+” on the unit (“ ” / “ ” on the remote controller) to adjust OSD function option, press “MENU” on the unit (“MENU1″” on the remote controller) to confirm and enter the next item until exit the menu. As follows:

PICTURE:

“ “: BRIGHT (adjust the brightness of image); CONTRAST (adjust the contrast of image); COLOR (adjust the tint of image); ENGLISH (adjust menu language).

VOLUME:

“ : Adjust the value of volume.

OPTION: : U/D overturn (adjust the position of U/D image); L/R overturn (adjust the position of L/R. image); ZOOM (to set the aspect ratio).

SYSTEM:

:S-COLOR (adjust color system: AUTO, PAL, NTSC, SECAM).
CLOCK:DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device
11 “ ‘: SLEEP (set sleep time); TINtE (adjust time); OFF-TIME (set off-time); ON-TfME (set on-time).

2. NTSC (TV)
Press “MENU” on the unit (“MENU I” on the remote controller) to display image menu, press “MENU” on the unit (“MENUI” on the remote controller) to select what you demanded items: Picture, Volume, Option, System, Preset, Clock, and the selected item’s background will be yellow, press “CH-” or “CH+” on the unit / ” on the remote controller) to select what you demanded items, and the (  11.D. 11 explanation of the item will display under the OSD menu. Press “V-“or “V+” on the unit (“ ” / “ ” on the remote controller) to adjust OSD function option, press “MENU” on the unit (“MENU I” on the remote controller) to confirm and enter the next item until exit the menu. As picture following:
PICTURE:DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device
12 “: BRlGHT (adjust the brightness of image); CONTRAST (adjust the contrast of image); COLOR (adjust the tint of image); ENGLISH (adjust menu language).
VOLUME:DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device
13 : Adjust the value of volume.
OPTION: DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device
14 : U/D overturn (adjust the position of U/D image); . L/R overturn (adjust the position of L/R image); ZOOM (to set the aspect ratio).

SYSTEM:DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device
15

: S-COLOR (color system: NTSC); S-SYS (sound ‘system: M); SWAP (skip the channel which you dislike); COPY (copy channel).

PRESET:DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device
16 “ “: TV TYPES (select the TV type: ATV [Antenna TV receiver], CTV [Cable TV receiver]); AUTO-SEARCH (the TV tuner can search all channels and it be added to the storage); FlNE (TV signal receiver adjustment); BAND (to adjust the band of channel); POSlTlON (channel selection); SKIP (skip function on/ofl).
CLOCK:DELVCAM DELV-7XLPRO-ATSC LCD Monitor - device
17 ,: SLEEP (set sleep time); TIME (adjust time); OFF- TIME (set off-time); ON-TIME (set on-time).
3.AV
Use “MENU” on the unit (“MENU I” on the remote controller) to display image menu. the operation method is the same with the above (image menu in ATSC).

Main Parameter

Model Model 1 Model 2
Display Size 7″ 9″
Screen Resolution 480*234 640*220
Brightness 250 cd/m2
Contrast 300:1
Video 1 AV oiltput, 2 AV input
Audio Output 2*500 mW audio amplifier output, compatible

with double tracks earphone output
Color System| ATSC/NTSC (optional: PAL, SECAM)
Sound System| M
Power Supply| DC 12V, ≤ 800 mA
Overall Power Consumption| ≥ 10 W

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals