DORMAN 924-893 Ignition Lock Cylinder Instruction Manual

DORMAN 924-893 Ignition Lock Cylinder

Product Information

Specifications:

• Product Model: 924-893
• Product Type: Ignition Lock Cylinder
• Recommended Skill Level: Intermediate to Advanced
• Required Tools: Safety glasses, screwdriver or pick
• Manufacturer Contact: 1-800-523-2492

Product Usage Instructions

Removal Instructions:

1. Disconnect the negative battery cable.
2. Remove the column tilt lever by pulling straight out, if equipped.
3. Remove the column lower cover by removing mounting screws.
4. Remove the upper column cover by removing the retaining screw and lifting it off the column.
5. Remove the ignition lock cylinder by rotating it to the start position, then insert a small screwdriver or pick into the release hole and pull the lock from the column.

Installation Instructions:

1. Install the ignition lock cylinder. If the lock does not seat into the housing, use a screwdriver to align the internal mechanism with the new lock cylinder.
2. Reinstall the steering column upper trim cover and screw.
3. Reinstall the lower steering column trim cover and retaining screws.
4. Reinstall the tilt lever if equipped.
5. Reconnect the negative battery cable and verify the proper operation of the ignition lock.

If you encounter challenges or have suggestions during installation or operation, please contact our Technical Assistant at 1-800-523-2492.

Frequently Asked Questions

Q: I don’t have a service manual, can I still install this part?

A: It is recommended to refer to the appropriate shop manual for your vehicle to obtain specific service procedures. If you lack the skill or tools required, seek the services of a qualified technician.

Q: What should I do if the ignition lock cylinder does not seat properly during installation?

A: Use a screwdriver or similar tool to align the internal mechanism with the new lock cylinder to ensure proper seating.

ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

REMOVAL/INSTALL OF IGNITION LOCK CYLINDER (924-893) Cadillac 2000–1999, Chevrolet 2002–1998, GMC 2000–1998

PLEASE WEAR SAFETY GLASSES!

Removal Instructions

• STEP 1: Disconnect negative battery cable.

• STEP 2: Remove column tilt lever by pulling straight out, if equipped.

• STEP 3: Remove column lower cover by removing mounting screws.

• STEP 4: Remove upper column cover by removing retaining screw and lifting off of column.

• STEP 5: Remove ignition lock cylinder by rotating to start position. While holding ignition in start position, insert small screwdriver or pick into release hole and pull lock from column.

Installation Instructions

• STEP 1: Install ignition lock cylinder. If lock will not seat into housing use a screwdriver to align internal mechanism with new lock cylinder.

• STEP 2: Reinstall steering column upper trim cover and screw.

• STEP 3: Reinstall lower steering column trim cover and retaining screws.

• STEP 4: Reinstall tilt lever if equipped.

• STEP 5: Reconnect negative battery cable and verify proper operation of ignition lock.

We appreciate your opinions regarding this product!
Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product.
1-800-523-2492

Disclaimer:
Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature.

©2018 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>