VIVO STAND-RACE1B Premium Racing Simulator Cockpit with TV Mount and Shelf Kit Instruction Manual

: June 17, 2024
: Vivo

Table of Contents

Package Contents
Included Hardware & Tools
Tools Needed
Weight Capacity
ASSEMBLY STEPS
CABLE MANAGEMENT
SEAT ADJUSTMENT
OTHER ADJUSTMENTS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIVO STAND-RACE1B Premium Racing Simulator Cockpit with TV Mount and Shelf Kit Instruction Manual

CAUTION!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo- us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

Safety Instruction
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

We’re Here for You

Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Give us a Call:
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S

Chat Us:
www.vivo-us.com
AVG. RESOLUTION TIME (within office hrs): < 15 M

Email Us:
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr

Package Contents

A (x1)
Front Support Frame
B (x2)
Side Support Bar
C (x1)
Rear Support Bar
D (x2)
Support Bar Spacer
E(x1)
Right Brace
F (x1)
Left Brace
G (x1)
Footrest
H (x1)
Wheel Mount
I (x1)
Right Chair Support with Lock
J (x1)
Left Chair Support
K (x1)
Chair Seat
L (x1)
Chair Back
M (x1)
Right Side Cover
N (x1)
Left Side Cover
O (x4)
Foot Pad
P (x1)
Shifter Support Bar
Q (x1)
Shifter Mount
R (x4)
Cable Clip
S (x6)
Ziptie

Included Hardware & Tools

S-A (x4) Spacer
S-B (x4) M8x30mm Hex Head Screw with Washers
S-C (x4) M5x8mm Screw
S-D (x22) M8x16mm Screws
S-E (x4) M8x30mm Screws
S-F (x2) M8x60mm Screws
S-G (x2) M6x15mm Screws
S-H (x2) M8x50mm Screws
S-I (x2) M8 Nut
T-A (x1) 5mm Allen Wrench
T-B (x1) Wrench

Tools Needed

Phillips Screwdriver

Weight Capacity

Seat

Gear Shift

ASSEMBLY STEPS

STEP 1
Screw two Foot Pads (O) into the underside of Front Support Frame (A).

Place one Support Bar Spacer (D) onto the front, angled end of each Side Support Bar (B), then connect to the Front Support Frame (A) using M8x60mm Screws (S-F). Tighten using 5mm Allen Wrench (T-A).
Assembly Instruction

STEP 2
Screw remaining Foot Pads (O) into Rear Support Bar. Then insert the Side Support Bars (B) into the Rear Support Bar (C), and secure using M8x16mm Screws (S-D) and 5mm Allen Wrench (T-A).
Assembly Instruction

STEP 3
Remove pre-installed Screws (A-1) from Front Support Frame (A). Assemble Right and Left Braces (E, F) to the frame using previously removed Screws (A-1), M8x16mm Screws (S-D) and 5mm Allen Wrench (T-A).
Assembly Instruction

STEP 4
Install the Footrest (G) to the Front Support Frame (A) using M8x16mm Screws (S-D) and 5mm Allen Wrench (T-A). Ensure Screws go into the rear mounting holes on Footrest.
Assembly Instructio

Insert M8x16mm Screws (S-D) into the front holes of Footrest (G) and Front Support Frame (A) to hold Footrest at one of three heights, as shown below. Tighten all Screws using 5mm Allen Wrench (T-A).
Assembly Instruction

STEP 5
Attach Wheel Mount (H) to Front Support Frame (A) using M8x16mm Screws ( S-D) and 5mm Allen Wrench **(T-A).

**

Adjust the wheel mount height and angle by removing the pre-installed bolts with washers from the sides, then reinstall while holding the mount at the desired height and angle.
Assembly Instruction

STEP 6
Extend the Slider (I-1) on Right Chair Support with Lock ( I) by lifting on the Lever (I-2) and pulling forward.
Assembly Instruction

Pull and extend Slider (J-1) forward on Left Chair Support (J).

STEP 7
Connect Right and Left Chair Supports (I, J) to the Chair Seat (K) using Spacers (S-A) and M8x30mm Screws (S-E) into to front holes on Sliders (I-1, J-1) with 5mm Allen Wrench (T-A).
Assembly Instruction

Slide Supports (I, J) forward to reveal rear mounting hole. Secure using Spacers (S-A), M8x30mm Screws (S-E), and 5mm Allen Wrench.
Assembly Instruction

STEP 8
Mount Chair Seat (K) with Supports to assemble frame using M8x16mm Screws (S-D) with 5mm Allen Wrench (T-A).
Assembly Instruction

STEP 9
Assemble Chair Back (L) to Side Brackets (K-1) on Chair Seat (K) using M8x30mm Hex Head Screw with Washers (S-B) and a Phillips screwdriver. Install Left and Right Side Covers (M, N) to Brackets using M5x8mm Screw (S-C), and tighten with a Phillips screwdriver.
Assembly Instruction

STEP 10.1
The Shifter Mount can be installed on either the right or left side, based on your preferences. Follow the steps outlined below and on the next page to assembly to your desired side.

OPTION A: Right Side Shift Lever
Attach Shifter Mount (Q) to the top of Shifter Support Bar (P) using M6x15mm Screws (S-G), making sure the long end of Mount is in the back, and tighten with a Phillips screwdriver.
Assembly Instruction

Connect the Shifter Support Bar (P) to the right side of the frame using M8x50mm Screws (S-H) and M8 Nuts (S-I). Tighten using 5mm Allen Wrench (T-A) and Wrench (T-B).
Assembly Instruction

STEP 10.2
OPTION B: Left Side Shift Lever
Attach Shifter Mount (Q) to the top of Shifter Support Bar (P) using M6x15mm Screws (S-G), making sure the long end of Mount is in the back, and tighten with a Phillips screwdriver.
Assembly Instruction

STEP 11
Adjust the mount angle by removing the pre-installed bolts from the sides using 5mm Allen Wrench (T-A). Reinstall while holding the mount at the desired angle.