V I V O STAND-V100E Pneumatic Arm Single Ultrawide Monitor Desk Mount Instruction Manual
- June 17, 2024
- V I V O
Table of Contents
Mechanical Arm Single Ultrawide Monitor
Desk Mount
Instruction Manual
STAND-V100E Pneumatic Arm Single Ultrawide Monitor Desk Mount
SKU: STAND-V100E
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v100e
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach Clamp Brace (F) to Base (A) using M6x12mm Screws (S-B) and tighten with
4mm Allen Wrench (T-A). Thread M10x63mm Screws (S-D) into Clamp (G) and place
Clamp Plate (E) on top.
Loosen bolts on back of Clamp (G) using 4mm Allen Wrench (T-A), leaving 6mm of thread exposed. For a desk thickness of 3/8” to 2” (10 – 50mm), hang assembled clamp into top 4 slots of Clamp Brace (F), or for a desk thickness of 1.5” to 3” (40 – 80mm), into lower 4 slots. Tighten using 4mm Allen Wrench (T-A). Secure to the desktop using 6mm Allen Wrench (T-B).
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Mark drill holes using the larger outer holes on Clamp Plate (E), drill two
3/8” (10mm) holes. Insert M10x63mm Screws (S-D) with Clamp Plate (E) up
through the underside of the desk and tighten to Base (A) using the 6mm Allen
Wrench (T-B).
STEP 2
To limit Lower Arm (B) rotation to 90°, adjust the set screw located inside of
the opening in the bottom of Lower Arm (B). Back the screw off 5-6 turns,
which is approximately 5mm (3/16”) using 4mm Allen Wrench (T-A). For full
roatation, fully tighten the set screw. Place Lower Arm (B) on top of Base
(A), and secure by turning the lower set screw in back with 4mm Allen Wrench
(T-A).
STEP 3
Place Spring Arm (C) on top of Lower Arm (B), and secure by turning the set
screw in back with 4mm Allen Wrench (T-A).
STEP 4
Attach VESA Adapter (D) using M8x35mm Screws (S-C) and M8 Nuts (S-A) on Spring
Arm (C) using 6mm Allen Wrench (T-B). Unscrew Thumbscrew (D1) on VESA Adapter
(D) and remove VESA Plate (D2).
STEP 5
Install the VESA Plate (D2) to monitor using M4x12mm Screws (M-A) or M5x12mm
Screws (M-B) with M5 Washers (M-C), making sure the arrow in back is pointing
up.
STEP 6
Hang VESA Plate (D2) on VESA Adapter (D) and secure using Thumbscrew (D1).
STEP 7
If needed, adjust Spring Arms (C) to support the monitors using the 6mm Allen
wrench (T-B). Turn the screw in back counter-clockwise to decrease support,
and clockwise to increase.
STEP 8
Remove cable cover on Spring Arm (C) by pulling the sides away from the arm to
unclip them. Slide cable cover on Lower Arm (B) forward to remove it. Manage
cables in cable covers and re-install.
Adjust as Desired
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 11/10/23
REV1
v1.0
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Single Ultrawide Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>