Newell NP-FZ100 Multifunctional LCD Charger Instruction Manual

Newell NP-FZ100 Multifunctional LCD Charger

SAFETY INSTRUCTIONS

Before using the product, please read the following instruction manual carefully and keep it for future reference. When transferring the product to a third party, it is advisable to include the instructions.

1. Do not charge batteries that are not intended for this product.
   It may damage the battery and cause leakage, explosion, personal injury, and property damage.

2. Use indoors or in a vehicle. Do not expose to rain or snow.

3. Store in a dry, cool and ventilated place. Do not expose the device to moisture or rain.

4. Do not leave unattended while charging.

5. Do not drop or place heavy objects on the device.

6. Keep out of reach of children.

7. The charger can operate in a temperature range of 0°C – 40°C.

8. Keep away from heat sources and high-temperature areas and do not expose to direct sunlight.

9. The charger will heat up slightly, but it is normal.

10. The batteries should be removed from the charger when it is not in use.

11. If you notice smoke or a strange smell coming from the device, immediately disconnect the power. Do not disassemble. Disassembling the unit will void the warranty. If there are problems with the lamp, bring it to an authorized service center.

CONSTRUCTION

1. USB-C input
2. USB-A output
3. USB input cable
4. Battery compartment
5. Battery-level display screen
6. Opening
7. Card reader SD
8. Card slot SD
9. Power button
10. Viewing window
11. Opening

LCD display

1. CH1 battery level display
2. Charging indication
3. Output
4. Card reading indication
5. CH2 battery level display

CHARGING BATTERIES

1. Put 1 or 2 lithium-ion batteries (see the battery compartment inside the charger for the model), and observe the correct position to avoid forcing the batteries in the wrong way.
2. Take out the built-in USB cable and plug it into a USB charger or other 5V power source with an input requirement of 25V/2A.
3. Alternatively, connect a USB-Type-C cable to the corresponding 5V input port.
4. The INPUT red light on the LCD screen will turn on during normal charging, and the percentage will display the battery level accordingly.
5. The display will show 100% when the charging is complete.
6. The battery level display is only an approximate value, not an absolute value.
   To check the most accurate charge value, disconnect the cable from the power source and then use the power button.

POWERBANK FUNCTION

1. Place one or two lithium-ion batteries into the charger.

2. Insert the USB charging cable into the charger’s USB output interface.

3. Connect the other end of the charging cable to the device to be charged, press the POWER DISPLAY button, and the OUTPUT light will turn green. The USB output is ≥ 5V/2A. The battery discharges from left to right, and the battery level decreases as the numbers decrease. Press the POWER DISPLAY button again to turn off the discharge.
   If there is no load, the output will automatically stop after 10 seconds.

4. The battery level display is only an approximate value, not an absolute value.

READING SD CARD

1. Remove the batteries from the charger. (The computer may not provide enough power.)
2. Take out the built-in USB cable and plug it into the computer (the charger’s own cable must be used for card reading).
3. Insert the SD card correctly into the charger, and the computer will recognize the SD card. The charger’s SD light will turn blue, Flickering to indicate that it is reading data.
4. The SD card and computer may affect the card reading speed.

SPECIFICATIONS

WASTE MANAGEMENT
The crossed-out trashcan symbol means that waste electrical and electronic equipment, batteries and packagings must not be placed with other household waste. They must be handed over to a separate waste collection system.

WARRANTY
Newell products are covered by a 40-month manufacturer’s warranty.

The manufacturer reserves the right to change the information contained in this manual without prior notice.
Made in China, In China heraestellt, Hecho en China. Fabbricato in Cina.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>