GUANGDONG M558 Wireless Doorbell User Manual
- June 17, 2024
- Guangdong
Table of Contents
Smart Wireless Doorbell
User Manual
M558 Wireless Doorbell
Operation Guide
Plug the
doorbell receiver into the AC outlet, the receiver rings “Dingdong” once ,
means that the receiver has entered working mode. 
Tear offthe
back glue of t the doorbell transmitter and stick iton the wall. Press and
hold for more than 5 seconds to release it. After confirming that the transmitter is firmly
fixed, press the transmitter, the receiver will emit a melody means that the
transmitter working normally.
This wireless doorbell has a power outage memory function, power off and restart will remember the ringing sound of a bell for the last time.
Setting and ADjusting
Volume control
Press the [Volume] button to adjust the volume, with 4 levels available.
Set up
Select Song
Press the [Select Song] button to select a melody, with 33 songs available.
Factort reset
Pull the doorbell receiver out of the socket, press and
hold the [Volume] button and insert it into the socket for 3 seconds.
The doorbell receiver will emit a beep indicating that all transmitters and
detectors have been successfully deleted after factory reset, all accessories
have no songs.
Add doorbell transmitter
Short press the [Set] button The doorbell receiver will ring and then release
your hand. Press the button on the doorbell transmitter, and the doorbell
receiver will “ding dong” once, indicating successful pairing.
Short press the [Select Song] button The transmitter can switch music at any
time.
But adding PIR motion sensors to the doorbell receiver is in welcome mode, and
adding door and window sensors is in alarm mode. This is fixed.
Long press and hold the [Select Song] button for 3 seconds, and the doorbell
receiver will emit a beep, triggering the button to learn. In this way, the
accessory has music memory function. No matter how the music switches.
All accessories always keep learning songs.
If you want to learn multiple doorbell transmitters, please continue to
trigger other doorbell transmitters. After learning, press the [Volume] button
once to exit the learning process. After exiting, you can trigger the
transmitter you just learned to test whether the learning is correct.
Technical Parameters
-
Working Voltage: AC 100-240V
-
Working Current: <100MA
-
Wireless Frequency: 433MHz
-
Working Temperature: -10°C——50°C
-
Wireless Distance: 100meters (Open area)
-
Receiver Size: 974817mm (Not include plug)
-
Volume Decibels: 20-100db (4 levels adjustable volume)
-
Working Voltage: 3V (CR2032 button battery)
-
Working Current: 8mA
-
Wireless Frequency: 433MHz
-
Working Temperature: -10°C——50°C
-
Transmitting Distance: 100meters (Open area)
-
Transmitter Size: 794011mm
Packing List
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>