Guangdong Sinmar Electronic Science and Technology Co Ltd SIN-M01 Digital Industrial PC Instruction Manual

Guangdong Sinmar Electronic Science and Technology Co Ltd SIN-M01 Digital

Industrial PC

Product Specifications

• Product Name: Industrial PC SIN-M01
• Product Model: SIN-M01
• LCD Screen Size: 10.1 inches
• System Version: Android 11
• CPU: Cortex-A55x4 2.0GHz
• System Parameter: Mali-T764 GPU, 2GB RAM, 16GB ROM
• Resolution: 1280 x 800
• Luminance: 300cd/m2
• Operating Voltage: DC 12V/POE48-56V 0.52A
• Power Supply Parameter: 3A, 15W-36W
• Standby Power: 0.5W

Product Usage Instructions

Interface Description

• USB: For connecting USB devices or flash drives
• LAN Interface/POE Supply Port: 10/100M TCP/IP, POE48-56V 0.52A
• COM Port: 485 agreement
• Door Status Sensor Port: Connects to the door status sensor switch
• DC Interface: 12V-3A

Camera Parameter

• Regular Camera: Aperture – 2.4mm, Focal Length – 1.7mm, Pixels – 100W
• Wide Motion Camera: Aperture – 2.4mm, Focal Length – 4.3mm, Pixels – 200W

Swipe Card Module Parameter

• Support Protocol: ISO14443A Mifare1K/4K NXP S50, NXP S70
• Communication Interface: TTL at 9600bps
• Card Reading Distance: 0~60mm

Frequently Asked Questions (FAQ)

Q: What is the power supply requirement for the device?

A: The device operates on DC 12V or POE48-56V with a current of 0.52A.

Q: What is the screen resolution of the LCD?

A: The LCD screen resolution is 1280 x 800 pixels with a luminance of 300cd/m2.

Product introduction

• This is a digital industrial PC equipped with the Android 11 system. It features two power supply options – PoE power and adapter power.
• The device includes a 10.1-inch display screen, a camera, and a card reader, as well as a door magnetic interface, and 485/232 protocol interfaces.
• It can connect to wireless networks/Ethernet and enables facial recognition and digital control of industrial machinery products. With a wide range of applications, this device offers convenient and efficient solutions for industrial use.

Interface description and hardware specifications

Interface Description

• USB: A device or USB flash drive connected to a USB port
• LAN interface/POE supply port: 10/100M TCP/IP， POE48-56V⎓ 0.52A
• COM: 485 agreement
• Door status sensor port: Connects to the door status sensor switch
• DC interface: 12V-3A

Hardware specifications

Camera parameter

Swipe card module

Bluetooth RF Specifications and WiFi RF Specification

2.4G WiFi RF Specification

802.11g (OFDM): BPSK, QPSK, 16QAM, 64QAM;

802.11n (OFDM): BPSK, QPSK, 16QAM, 64QAM;

Date Rate| 802.11b: 1, 2, 5.5, 11Mbps;

802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps;

802.11n (HT20): MCS0~MCS7(1T1R_SISO) 6.5~72.2Mbps;

802.11n (HT40): MCS0~MCS7(1T1R_SISO) 13.5~150Mbps;

Frequency Tolerance| ≦±15ppm
2.4G Transmitter Specifications
RX Rate| TX Power| TX Power Tolerance| EVM
802.11b@1~11Mbps| 17dBm| ±2.0dBm| ≦-10dB
802.11g@6Mbps| 17dBm| ±1.5dBm| ≦-10dB
802.11g@54Mbps| 14dBm| ±1.5dBm| ≦-25dB
802.11n@HT20_MCS0| 16dBm| ±1.5dBm| ≦-10dB
802.11n@HT20_MCS7| 14dBm| ±1.5dBm| ≦-28dB
802.11n@HT40_MCS0| 16dBm| ±1.5dBm| ≦-10dB
802.11n@HT40_MCS7| 13dBm| ±1.5dBm| ≦-28dB
2.4G Receiver Specifications
RX Rate| Min Input Level(Typ)| Max InputLevel(Typ)| PER
802.11b@1Mbps| -93dBm| -10dBm| < 8%
802.11b@11Mbps| -86dBm| -10dBm| < 8%
802.11g@6Mbps| -90dBm| -15dBm| < 10%
802.11g@54Mbps| -72dBm| -15dBm| < 10%
802.11n@HT20_MCS0| -88dBm| -15dBm| < 10%
802.11n@HT20_MCS7| -67dBm| -15dBm| < 10%
802.11n@HT40_MCS0| -86dBm| -15dBm| < 10%
802.11n@HT40_MCS7| -66dBm| -15dBm| < 10%

Bluetooth Receiver Specifications

Classic_BT

BR/EDR), Bluetooth 4.2 (Bluetooth Low Energy _ BT_LE) FHSS

Frequency Range| 2.4~2.4835GHz(2.4GHz ISM Band)
Channels| Bluetooth Classic: Ch0~Ch78 (For 1MHz Channels);

Bluetooth Low Energy: Ch0~Ch39 (For 2MHz Channels);

Power Classes| Bluetooth Classic: Class1;

Bluetooth Low Energy: Class1.5;

Date Rate & Modulation| BR_1Mbps: GFSK; EDR_2Mbps: π/4-DQPSK; EDR_3Mbps: 8DPSK;

LE_1Mbps: GFSK;

---|---
Bluetooth Transmitter Specifications
Items| Min| Typ| Max
TX Power
BR_1M TX Power| 1| 6| 8
EDR_2/3M TX Power| 1| 6| 8
LE_125K~1M TX Power| 1| 6| 8
1DH1 TX Power| 1| 6| 8
2DH3 TX Power| 1| 6| 8
3DH5 TX Power| 1| 6| 8
Bluetooth Receiver Specifications
Items| Sensitivity| Maximum Input Level
Maximum Input Level| BER| Input Level(Typ)| BER
BR_1M| -92dBm| ≦0.1%| -20dBm| ≦0.1%
EDR_2M| -90dBm| ≦0.01%| -20dBm| ≦0.1%
EDR_3M| -96dBm| ≦0.01%| -20dBm| ≦0.1%
LE_1M| -92dBm| ≦30.8%| -20dBm| ≦0.1%
1DH1| -92dBm| ≦30.8%| -20dBm| ≦0.1%
2DH3| -90dBm| ≦30.8%| -20dBm| ≦0.1%
3DH5| -86dBm| ≦30.8%| -20dBm| ≦0.1%

Declaration of Conformity and matters need attention

Declaration of Conformity Hereby, Guangdong Sinmar Electronic Science and Technology Co., Ltd declares that this industrial PC complies with essential requirements and other relevant provisions of Directive 2014/53/EU.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Please read the following safety precautions carefully before using this computer

1.  Do not use accessories not recommended by the manufacturer. Improper use of accessories may cause accidents
2. Please use the power adapter provided with the industrial computer. Before connecting the power cable to the power socket, check whether the voltage specified by the industrial computer is suitable for the local power supply conditions.
3. Please use the power adapter provided with the industrial computer. Before connecting the power cable to the power socket, check whether the voltage specified by the industrial computer is suitable for the local power supply conditions.
4. Please unplug the power when no one is indoors or not in use for a long time.
5. When you need to clean, please turn off the machine and unplug the power plug. Please wipe the screen with a soft cloth that cannot dry. Do not wash the screen directly with water or detergent.
6. Do not place the equipment in an unstable and easy toppling place; Do not place the device in direct sunlight, heavy wind and sand, heavy oil smoke, electric heater, boiler, and other high-temperature heat sources or strong light sources. Do not place the device in places where strong electricity, strong magnetic field, and strong radiation directly affect the device. Do not use the device in harsh environments such as damp, liquid dripping, strong corrosive gas, or flammable gas leakage. Do not place heavy objects on the device. Otherwise, the device may not work properly due to excessive pressure.
7. Do not place the device near the electric heater or heater. When the equipment is transferred from the low-temperature area to the high-temperature area, to make the inner condensation fully volatilize, please place for a while and then turn on the power;
8. Do not place the device near the electric heater or heater. When the equipment is transferred from the low-temperature area to the high-temperature area, to make the inner condensation fully volatilize, please place for a while and then turn on the power;
9. Place the device in a well-ventilated place to ensure good heat dissipation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>