Guangdong ximico digital technology Co LTD 2BF3M-Z42 Projector User Manual

Guangdong ximico digital technology Co LTD 2BF3M-Z42 Projector

IMPORTANT SAFEGUARDS
Please read this manual thoroughly before using it and keep it for future reference.

Safeguards Information
Safeguards Information: The disconnecting device for this product is the appliance coupler (AC socket), which is located at the right-hand side of the product. When the projector is not in use, disconnect the power cable from the projector via the appliance coupler. No other objects should be placed near the appliance coupler, for it may prevent the projector from being disconnected from the power supply.

Packing list

Function Overview

1. Lens

2. Cameras

3. Left vocal tract

4. Subwoofer exit

5. Right track

6. Power switch

7. RJ45(network cable interface)

8. DH (network cable interface)

9. USB (network cable interface)

10. 3.5 mm headphone jack

11. AV(network cable interface)

12. IR remote control receiver head

13. Power Jack

14. Cooling Air Inlet

15. Cooling Air Inlet

16. Cooling Air Inlet

17. Host nameplate

18. Screw Hole in the footrest

19. Lifting and fixing screw holes (remove four shock-proof floor mats for hoisting with 1/4-inch nut with twist-in depth of 10 mm or less)

Warning: screw torsion depth of hanger less than 10mm may result in abnormal machine structure and function

Quickstart

1. Remove lens cap (optional)
2. Plug the power cord into the socket and then into the machine
3. Press the ON/off button to open the projector

Description of remote control function

(appearance should be based on real object)

For first-time use, use this method

Manual pairing:
Settings-bluetooth settings-search-at the same time long press the remote control key-indicator flashing let go-the interface shows connected Bluetooth

Signal source connection

After entering the main intertace, press the remote control signal source,” ” select the needed signal channel in the pop-up interface, such as “HD, USB, AV”, etc.. Press the remote control “OK” key, then enter the corresponding signal source state.

Specifications

Projection distance

Refer to the table below and position the projector at a distance from the projection screen according to the preset graphic dimensions.
When installing, place the projector on a firm, smooth countertop or use a hanger on the ceiling. Sound ventilation around the fuselage is good, do not cover or block the vent, in the vent 30cm distance, should not be any blocking objects.

Note: The above data are for reference only, please refer to the actual measurement.

Functional use

map projection
Setting-projection-projection setting-projection mode-can refer to the map under the test

Points to note:

1. When using the hoisting method, the projector can not be higher than thetop edge of the screen, otherwise, it will affect the image effect or trapezoid correction.
2. Make sure to install the projector on the symmetrical curve of the screen to avoid distortion of the image.
3. after the installation of the projector, make sure that the surrounding ventilation is good, no object to cover or plug the projector vent.
4. in the installation process, please do not live operation, lest cause electric shock danger or projector circuit failure.
5. just installed projector, the first boot, the image may appear above and below the trapezoidal distortion and Blur, please refer to the “Projection settings” to receive adjustments.

Note:
In order to install, the projected image will not appear geometric distortion (trapezoid state), please install the projector vertically on the left and right symmetry axis of the screen. (see below)

Functions

1. Language settings
   Restore factory settings – select Lauguage – Confirm Projection settings
   the first time the projector is used, such as auto-focus micro-focus, the need to focus the image;

2. manual focus
   In the case of blurred picture, press the remote control focus key “F+”, “F-” , can adjust the lens focus, light point or long press the focus key to clear picture (as shown below)
   Setting-projection-projection setup-image focus-manual focus.

3. Automatic trapezoid correction
   Setting-projection-projection setting-trapezoidal correction-automatic trapezoidal correction on boot/automatic displacement trapezoidal correction- press OK to open

4. Manual trapezoid correction
   Setting-projection-projection setting-trapezoid correction-press OK-manual trapezoid according to Operation Instructions

5. Zoom in
   Setting-projection-projection settings-screen zoom-press OK to confirm-adjust the appropriate size

6. Setting-projection-projection setting-trapezoid correction-intelligent automatic obstacle avoidance/screen automatic obstacle avoidance (press OK to open)
   Intelligent automatic obstacle avoidance-automatic obstacle avoidance when encountered after opening Automatic screen entry-automatic screen entry after opening (screen black border)

7. Restore the factory setup
   Setting-system-system setup-resume factory setup-confirm

8. App installation
   Home page–APPS–My apps–install the selected apps

9. WI-FI connectivity
   Setting-network-wifi settings-select wifi-enter Password-done

10. Connect Biuetooth
    Setting–Bluetooth Setting–Turu on Bluetooth–At the same time,press the key around the remote control–Connect voice Assistant–Accomplish

11. FileManagei
    Home page-APPS-FileManagei-OK

12. Android with the same screen (make sure the phone and projector are connected to the same WI-FI)
    Home page-APPS-Miracast-OK-Connect according to instructions

13. Apple with the same screen (make sure the phone and projector are connected to the same WI-FI)
    Home page-APPS-iOSCast-OK-Connect according to instructions

14. Signal source
    Settings – Signal source – Select source – Adjust up and down using remote

Safety Notes

To maintain the performance and reliability of the projector, leave at least 30cm of space between the projector and the wall, and the projector should be placed horizontally.

• Do not install in poorly ventilated areas.
• Do not install in hot and humid locations

• Do not block ventilation holes (intake
• Do not install in dusty, smoky or exhaust) locations

Product Warranty Information

Notes and Instructions:

1. The above table is not a description of product specifications and configurations, which should be based on the actual condition of the product you are purchasing.
2. Consignment repair: means that when you apply for the service, we will arrange for the logistics to come to you or you will use the logistics on delivery method (the specific product service customer instructions shall prevail)

The faulty product will be sent back to the designated repair centre and returned to you by post after the repair has been completed. If there is any special handling of the repair process, such as non-damage, out-of-warranty or other non-compliance with the service requirements, we will contact you to confirm the situation before dealing with it. Please ensure that your contact is open during the repair period and that you are obliged to cooperate with us in the audit of the relevant invoice if necessary.

Warranty Card
Dear customer, this warranty card is the proof of your future warranty claim, please cooperate with the salesman to fill out and properly stored for backup!

Note:

1. this form should be confirmed by the seller’s seal;
2. this warranty card is equivalent to the “Three-pack voucher” for products for which the relevant “Three-pack” provisions may beused
3. the maintenance record shall be based on the maintenance certificate issued by the authorized service organization. Please keep it properly after applying for service.

In order to meet the laws, regulations and other requirements related to the restriction of hazardous substances in electronic and electrical products in China The  company declares the following about the hazardous substances in this product, classified by parts.

The name and content of toxic and harmful substances or elements in the product

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipmentinto an outlet on a circuit different from that to which the receiver is connected.
• Consultthe dealer or an experienced radio/ TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm(8 inches)during normal operation.
That changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>