Connect Tech CTIM-000454 GPS GNSS Receiver User Guide

June 1, 2024
Connect Tech

Connect Tech CTIM-000454 GPS GNSS Receiver

Connect-Tech-CTIM-000454-GPS-GNSS-Receiver-PRODUCT

Product Information

Specifications

  • Product Name: M.2 GPS
  • Model Number: CTIM-000454
  • Revision: 0.01
  • Release Date: 2021-03-01
  • Manufacturer: Connect Tech
  • Website: www.connecttech.com

Product Overview
The M.2 GPS is a compact GPS module designed for precise navigation and location tracking.

Block Diagram
The block diagram illustrates the internal components and connectivity of the M.2 GPS module.

Connector Summary & Locations
The module features various connectors including the M.2 Edge Connector, External I/O Connector, and Active Antenna Connector for seamless integration into different systems.

Interface Pin-outs
Detailed pin-out information for the M.2 Edge Connector,External I/O Connector, and Active Antenna Connector is provided for easy setup and configuration.

Product Usage Instructions

Detailed Feature Description
Refer to the user manual for a detailed description of the features and functionalities of the M.2 GPS module.

Cables
Use the specified cables provided with the module to ensure proper connectivity and performance.

FAQ

Q: What should I do if I encounter technical issues with the M.2 GPS module?
A: If you experience difficulties, first contact the Connect Tech reseller from whom you purchased the product for assistance.
If further support is needed, reach out to Connect Tech’s support staff available 24/7 on their website at support/resource- center.

PREFACE

Disclaimer
The information contained within this user’s guide, including but not limited to any product specification, is subject to change without notice.
Connect Tech assumes no liability for any damages incurred directly or indirectly from any technical or typographical errors or omissions contained herein or for discrepancies between the product and the user’s guide.

Customer Support Overview
If you experience difficulties after reading the manual and/or using the product, contact the Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties.
In the event that the reseller is unable to resolve your problem, our highly qualified support staff can assist you. Our support section is available 24 hours a day, 7 days a week on our website at: https://connecttech.com/support /resource-center/. See the contact information section below for more information on how to contact us directly. Our technical support is always free.

Contact Information

Contact Information

Mail/Courier| Connect Tech Inc. Technical Support 42 Arrow Road Guelph, Ontario Canada N1K 1S6
Contact Information| sales@connecttech.com support@connecttech.com www.connecttech.com

Toll Free:   800-426-8979 (North America only) Telephone: +1-519-836-1291

Facsimile:            519-836-4878 (on- line 24 hours)

Support| Please go to the Connect Tech Resource Center for product manuals, installation guides, device drivers, BSPs and technical tips.

Submit your technical support questions to our support engineers. Technical Support representatives are available Monday through Friday, from 8:30 a.m. to 5:00 p.m. Eastern Standard Time.

Limited Product Warranty
Connect Tech Inc. provides a 2-year Warranty for this product. Should this product, in Connect Tech Inc.’s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non-Connect Tech Inc. authorized modification or repair.

You may obtain warranty service by delivering this product to an authorized Connect Tech Inc. business partner or to Connect Tech Inc. along with proof of purchase. Product returned to Connect Tech Inc. must be pre-authorized by Connect Tech Inc. with an RMA (Return Material Authorization) number marked on the outside of the package and sent prepaid, insured and packaged for safe shipment. Connect Tech Inc. will return this product by prepaid ground shipment service.
The Connect Tech Inc. Limited Warranty is only valid over the serviceable life of the product. This is defined as the period during which all components are available. Should the product prove to be irreparable, Connect Tech Inc. reserves the right to substitute an equivalent product if available or to retract the Warranty if no replacement is available.
The above warranty is the only warranty authorized by Connect Tech Inc. Under no circumstances will Connect Tech Inc. be liable in any way for any damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use, such product.

Copyright Notice
The information contained in this document is subject to change without notice. Connect Tech Inc. shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Connect Tech, Inc.
Copyright 2021 by Connect Tech, Inc.

Trademark Acknowledgment
Connect Tech, Inc. acknowledges all trademarks, registered trademarks and/or copyrights referred to in this document as the property of their respective owners. Not listing all possible trademarks or copyright acknowledgments does not constitute a lack of acknowledgment to the rightful owners of the trademarks and copyrights mentioned in this document.

ESD Warning

Electronic components and circuits are sensitive to ElectroStatic Discharge (ESD). When handling any circuit board assemblies including Connect Tech COM Express carrier assemblies, it is recommended that ESD safety precautions be observed. ESD safe best practices include, but are not limited to:

  • Leaving circuit boards in their antistatic packaging until they are ready to be installed.
  • Using a grounded wrist strap when handling circuit boards, at a minimum you should touch a grounded metal object to dissipate any static charge that may be present on you.
  • Only handling circuit boards in ESD safe areas, which may include ESD floor and table mats, wrist strap stations and ESD safe lab coats.
  • Avoiding handling circuit boards in carpeted areas.
  • Try to handle the board by the edges, avoiding contact with components.

REVISION HISTORY

Revision Date Changes
0.00 2016-03-18 Initial Release
0.01 2021-03-01 Updated format

Replaced GPS-06T PN /w MSG095

INTRODUCTION

Connect Tech’s M.2 GPS is a GNSS receiver based on the very small industry- standard M.2 Type-2242-S3-B form factor. Using the USB bus, the M.2 GPS provides global positioning and time-stamp information, while taking up little space and power within a system. Also considering the existing support for Windows and Linux, the M.2 GPS can be easily integrated into any existing system, as well as easily implemented into new systems.

Product Features and Specifications

Specifications

Dimensions| 42 mm x 22 mm (M.2 Type-2242-S3-B)
Antenna Connector| HSC (MHF4), support for active antennas only
GPS| GPS, GLONASS, QZSS, Galileo

UBX, RTCM, NMEA protocols

I/O| TIMPULSE output synchronized with GPS time grid WHEELTICK input (used for Automotive Dead Reckoning) FWD input (used for Automotive Dead Reckoning) External Interrupt Input

External Battery Input

Cables| CBG162: External I/O Cable

CBG214: HSC (MHF4) to SMA Female Cable

Antenna| MSG095, VTGPSA-9, Active GPS/GLONASS antennas only
Environmental| -40ºC to +85ºC
Warranty and Support| 2 Years

Part Numbers / Ordering Information

Part Number

M2G201| M.2 GPS Receiver (Battery not included) populated with NEO-7N module
M2G202| M.2 GPS Receiver (Battery included) populated with NEO-7N module
M2G203| M.2 GPS Receiver (Battery not included) populated with NEO-M8N module
M2G204| M.2 GPS Receiver (Battery included) populated with NEO-M8N module
M2G205| M.2 GPS Receiver (Battery not included) populated with NEO-M8L module, supports Automotive Dead Reckoning
M2G206| M.2 GPS Receiver (Battery included) populated with NEO-M8L module, supports Automotive Dead Reckoning

PRODUCT OVERVIEW

Block Diagram

Connect-Tech-CTIM-000454-GPS-GNSS-Receiver-FIG- \(1\)

Connector Summary & Locations 

Connect-Tech-CTIM-000454-GPS-GNSS-Receiver-FIG- \(2\)

Interface Pin-outs
M.2 Edge Connector

The M.2 GPS pin-out is compliant to the M.2 Socket 2 with B Key. This module uses only +3.3V for input power and all I/O is +3.3V signaling.

Function M.2 Card Edge Connector
Location P3
Pinout Signal
NC 1
GND 3
GND 5
USB_D+ 7
USB_D- 9
GND 11
Connector Key 13
Connector Key 15
Connector Key 17
Connector Key 19
CONFIG_0 (GND) 21
NC 23
NC 25
GND 27
NC 29
NC 31
GND 33
NC 35
NC 37
GND 39
NC 41
NC 43
GND 45
NC 47
NC 49
GND 51
  NC
--- ---
NC 55
GND 57
NC 59
NC 61
NC 63
NC 65
NC 67
CONFIG_1 (GND) 69
GND 71

External I/O Connector

The pinout for the I/O connector is outlined in the table below.

Function| External I/O Connector|
---|---|---
Location| P2
Connector PN| 501568-0507 – Manufacturer: Molex
Mating Connector PN| 501330-0500 – Manufacturer: Molex CTI Cable #: CBG162
Pinout| Pin| Signal| Description
1| EXT_INT / WHEELTICK| External Interrupt Input or Speed pulse input
2| TIMEPULSE| Time pulse Output
3| FWD| Forward/Reverse indicator
4| GND| Digital Ground
5| EXT_BAT| External Battery Input

NOTE: WHEELTICK is only available on M2G205 and M2G206, otherwise this signal is EXT_INT

NOTE: FWD is only available on M2G205 and M2G206, otherwise it is not connected and should be left floating

Active Antenna Connector

Function| Active Antenna Connector|
---|---|---
Location| J2
Connector PN| MM4829-2702RA4 – Manufacturer: Murata
Mating Connector PN| HSC – MHF4 Socket Standard CTI Cable #: CBG214

DETAILED FEATURE DESCRIPTION

USB
The M.2 GPS uses a USB 2.0 Full Speed (12Mb/s) interface as the primary communication bus. The USB interfaces is connected between the GPS receiver and the M.2 card edge connector (pins 7/9).

TIMEPULSE
The TIMEPULSE output is a buffered and ESD protected signal from the GPS receiver. This signal connects to pin 2 of the External I/O Connector. It also drives the TIMEPULSE LED. By default, when satellites are not fixed this signal is High (3.3V). When satellites are fixed, this signal pulses at 1 pulse-per-second (1Hz) with a 20% duty cycle (200ms High, 800ms Low). For more information see the Receiver Description Including Protocol Specification document for your GPS receiver found in the Software Support section of this document.

W_DISABLE1#
The W_DISABLE# input from the M.2 card edge connector (pin 8) can be used to enable and disable power to the M.2 GPS module. When W_DISABLE1# is low, the module is disabled and no power is applied to the M.2 GPS. When W_DISABLE1# is High, the module is enabled and powered on. This signal is locally pulled up to 3.3V through a 100K ohm resistor.

External Interrupt Input/WHEELTICK Input
The external interrupt/WHEELTICK input is an ESD-protected input signal from the external I/O connector to the GPS receiver. On modules that do not support Automotive Dead Reckoning, this signal will always be an External Interrupt input, and this input can be used for control of the GPS receiver or for aiding. On modules that support Automotive Dead Reckoning (M2G205/M2G206), this signal is by default used as the WHEELTICK input and is used to provide speed pulse information to the module. If the speed pulse information is available from the host processor, then the information can be provided using software messages in the UBX protocol. If using software messages to provide speed pulse information, this signal can be configured as an external interrupt input. See the Receiver Description Including Protocol Specification document for your GPS receiver found in the Software Support section of this document. If this signal is not used, it should be left floating. Do not exceed 3.6V on this signal.

FWD
The forward/reverse signal is an ESD-protected input used on modules that support Automotive Dead Reckoning. This signal is used to indicate the moving direction of the module. An active high indicates moving forward and a low for moving backwards. If the forward/reverse information is available from a host processor, then this information can be provided to the module using software messages in the UBX protocol. For more information see the Receiver Description Including Protocol Specification document for your GPS receiver found in the Software Support section of this document. On modules that do not support Automotive Dead Reckoning, this signal should be left floating. Do not exceed 3.6V on this signal.

External Battery
The external battery input in an ESD-protected input from the External I/O Connector to the backup voltage supply of the GPS receiver. The purpose of a battery signal is to power internal memory for GPS almanac, ephemeris, and last position retention through power cycles. The voltage on this input signal should be greater than 2.0V and less than 3.6V. The supply of this signal should be able to provide at least 20uA continuous at room temperature, and 50uA at +85 degrees Celsius.

Local Battery and BAT_EN Header
There is a local battery supply on the M.2 GPS. The purpose of a battery signal is to power internal memory for GPS almanac, ephemeris, and last position retention through power cycles. The design includes a MS621 rechargeable battery which recharges itself when the unit is powered on. When power is removed from the unit the GPS receiver will typically consumer 15uA on its battery supply input at room temperature and 24uA at 85 degrees Celsius.

On-Board Indicator LEDs

LED Description
TIMEPULSE TIMEPULSE visual indicator. This LED will blink at the rate and

duty cycle of the TIMEPULSE output.

PWR

| ON: indicates the module is powered on and enabled OFF: indicated the module is not powered and is disabled the module is enabled/disabled using the W_DISABLE1# input from the M.2 card edge connector

Software Support for the NEO-7 and NEO-M8 GPS Receivers

The USB drivers for the NEO-7 and NEO-M8 GPS Receivers can be found on the u-Blox website: https://www.u-blox.com/en/product- resources?f[0]=property_file_product_filter%3A2668&f[1]=field_file_category%3A221
For configuration and setting options for the NEO-7 GPS receiver, please refer to the u-Blox 7 Receiver Description Including Protocol Specification V14 found on the u-Blox website: https://www.u-blox.com/en/product- resources?f[0]=field_file_category%3A209
For configuration and setting options for the NEO-M8N GPS receiver, please refer to the u-Blox M8 Receiver Description Including Protocol Specification found on the u-Blox website:
https://www.u-blox.com/en/product- resources?f[0]=field_file_category%3A209
Changing the configuring of the NEO modules is best accomplished using the u-center application provided by u-Blox. To get the u-center application for windows, please see the link below:
https://www.u-blox.com/en/product/u-center-windows

CABLES

CBG162 – External I/O Cable

Connect-Tech-CTIM-000454-GPS-GNSS-Receiver-FIG- \(7\)

501330-0500 Signal Open End (Un-terminated)
1

See I/O Connector Section for pin-out

| Un-terminated
2| Un-terminated
3| Un-terminated
4| Un-terminated
5| Un-terminated

CBG214 – Murata HSC to SMA Female Cable

Connect-Tech-CTIM-000454-GPS-GNSS-Receiver-FIG- \(6\)

Documents / Resources

| Connect Tech CTIM-000454 GPS GNSS Receiver [pdf] User Guide
CTIM-000454, CTIM-000454 GPS GNSS Receiver, GPS GNSS Receiver, GNSS Receiver, Receiver
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals