Westinghouse RMAW122C-06 Solar Area Wall Light Set Installation Guide
- June 16, 2024
- Westinghouse
Table of Contents
Westinghouse RMAW122C-06 Solar Area Wall Light Set
Product Information
Specifications:
- Model: RMAW122C-06 | RMAW122D-06 | RMAW122H-06
- Number of Light Fixtures: 2
- Battery Type: 3.7V, 2000 mAh lithium (18650) rechargeable battery
- Motion Sensor: Yes
- Standby Mode Lumens : 20
- Motion Activated Mode Lumens: Not specified
Pre-Installation
Before installing the solar area light with motion sensor, make sure you
have all the necessary hardware. The following hardware is included:
- A-Wall Anchors (4)
- B-Screws (4)
- C-Light Fixture (2)
- D-Mounting Plate (2)
Note: Some parts may be pre-assembled.
Tools Required
- Pencil
- Phillips-head Screwdriver
Installation
Marking the Location
Before mounting the light fixture, mark the desired location on the wall.
Use a pencil to mark two points that are 2.36 inches (60mm) apart.
Mounting the Light Fixture
- Align the mounting plate (D) with the marked points on the wall.
- Insert the screws (B) through the mounting holes on the plate and into the wall anchors (A).
- Slide down the light fixture (C) onto the mounting plate to lock it in place.
Note: The light fixture will stay on for 30 seconds when triggered by motion and revert back to standby mode of 20 lumens until motion is detected again.
Battery Instructions
For first-time use, the solar light needs to charge in full sunlight for
8-12 hours with the switch in the ON position to fully charge the battery. The
intelligent solar LED motion activated light measures the available battery
power capacity and adjusts thelight’s performance to maximize runtime.
Troubleshooting **
**
If the lights do not come on, follow these steps:
- Check the battery to ensure it is making secure contact with the terminals.
- If the issue persists, replace the battery with a new one.
Replacing the Batteries
- Slide the power switch to the OFF position.
- Use a Phillips head screwdriver to remove the 4 screws holding the battery cover in place.
- Replace the old battery with a new 3.7V, 2000 mAh lithium (18650) rechargeable battery.
- Align the battery cover properly and replace the 4 screws removed earlier.
- Slide the power switch to the ON position.
- For optimal performance, allow the light fixture to charge in full sunlight for 8-12 hours to fully charge the battery.
Warning: Do not dispose of lithium batteries in the municipal waste stream or by fire as batteries may explode. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride, or lithium ion) batteries.
Frequently Asked Questions (FAQ)
-
How long does it take to fully charge the battery?
The solar light needs to charge in full sunlight for 8-12 hours to fully charge the battery. -
What happens when the light is triggered by motion?
When triggered by motion, the light fixture will stay on for 30 seconds and then revert back to standby mode of 20 lumens until motion is detected again. -
Can I replace the battery with any other type?
No, you should only replace the battery with a new 3.7V, 2000 mAh lithium (18650) rechargeable battery. Do not mix different types of batteries. -
How many light fixtures are included?
The product includes two light fixtures. -
What tools do I need for installation?
You will need a pencil and a Phillips-head screwdriver. -
Can I dispose of the battery in the municipal waste stream?
No, you should dispose of the battery in accordance with Local, State, and Federal regulations. Do not dispose of lithium batteries in the municipal waste stream or by fire as they may= explode.
PRE-INSTALLATION
INSTALLATION
MARKING THE LOCATION
- Mark the location where you want to mount the light fixture (Part C).
- Measure the width of two holes on the back of the mounting plate (Part D) and mark holes for the 2 screws (Part A) on the surface. The distance between the two holes is 2.36in. (60mm).
- Drill two holes.
MOUNTING THE LIGHT FIXTURE
- Insert the wall anchors (Part B) so they are flush with the surface.
- Secure the mounting plate (Part D) in place with the screws (Part A).
- Mount the light on the mounting plate (Part D) by aligning the holes on the back of the light to the knobs on the front of the mounting plate. Align, insert, and slide down to lock in place.
NOTE: Light fixture will stay on 30 seconds when triggered by motion and
revert back to standby mode of 20 lumens until motion is detected. For best
performance, mount the light a minimun 6 feet (1.8 m) above the ground.
Detection range is 26 feet (8 m), detection angle is 120°. Light fixture uses
radio frequency technology to link, and should not be greater than 98 feet (30
m) between the neighboring/adjacent lights. When one light is triggered by
motion both lights will activate. The package includes 2 lights. These 2
lights are factory linked, and can not be linked with more of the same type
light or any other lights.
BATTERY INSTRUCTIONS
USE RECHARGEABLE BATTERIES ONLY.
- Only purchase the recommended type, size, and capacity of battery.
- Remove batteries from equipment when product will not be in use for an extended period of time.
- Dispose of the battery in accordance with local, state and federal regulations. (Do not burn or discard the battery in a municipal water system or other body of water.)
FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 -12 HOURS WITH THE SWITCH IN THE “ON” POSITION TO FULLY CHARGE THE BATTERY.
The intelligent solar LED motion activated light measures the available battery power capacity and adjusts the light’s performance to maximize runtime.
TROUBLESHOOTING
- Lights will not come on
- Check the battery to ensure that it is making secure contact with the terminals.
- If this doesn’t work, replace with a new battery.
- REPLACING THE BATTERIES
Slide the power switch to the “OFF” position. Use a Phillips head screwdriver to remove the 4 screws holding the battery cover in place. Replace old battery with a new 3.7V, 2000 mAh lithium (18650) rechargeable battery. Replace the battery cover by aligning it properly and replacing the 4 screws removed earlier. Slide the power switch to the “ON” position. For optimal performance, allow light fixture to charge in full sunlight for 8-12 hours, to fully charge the battery.
WARNING: Do not dispose of lithium batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries .
FCC WARNING
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
DO NOT RETURN THIS PRODUCT TO THE STORE
If you have questions or need assistance, please call customer service at
1-888-445-8974 or Email
solarlights@westingehouse.com.
Westinghouse are trademarks of Westinghouse Electric Corporation. Used under
license by Rayman Lights Inc. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>