ZALMAN I3-EDGE ATX MID Tower Computer Case User Manual
- May 15, 2024
- ZALMAN
Table of Contents
- Precautions
- Specification
- Accessories Component
- I/O Port
- Separating the side panel
- Mounting the main board
- Mounting PCI-E(VGA) card
- Mounting 2.5” SSD and HDD
- Mounting the 3.5” and 2.5” HDD
- Cable Connection
- Mounting the top fan
- Mounting the fan and radiator in the front
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ATX MID TOWER COMPUTER CASE
i3-SERIES
User’s Manual
※ To ensure safe and easy installation, please read the following precaution.
Product design and specifications may be revised to improve quality and
performance.
WWW.ZALMAN.COM Ver.021419
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated pur poses and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specification
| Model | i3 | i3-edge |
|---|---|---|
| Case Form Factor | ATX MID tower | |
| Dimensions | 445 x 196 x 456(H)mm | |
| Weight | 4.7kg | |
| Case Materials | Steel, Plastic | |
| Motherboard Support | ATX / M-ATX / M-ITX | |
| Maximum VGA Length | 360mm | |
| Maximum CPU Cooler Height | 156mm | |
| Maximum PSU Length | 180mm | |
| PCI Expansion Slots | 7 | |
| Case Drive Bays | 2 x Combo (3.5″ or 2.5″), 3 x 2.5″ | |
| Fan Mount Locations | Front | 3 x 120mm |
| Top | 2 x 120mm | |
| Rear | 1 x 120mm | |
| Fans Included | Front | 3 x 120mm(with White LED effect) |
| Rear | 1 x 120nnm(with White LED effect) | |
| Radiator Mount Locations | Front | 120mm / 240mm |
| I/O Ports | 1 x Headphone, 1 x Mic, 2 x USB 2.0, 1 x USB 3.0, 1 x Fan |
controller
Accessories Component
I/O Port
| # | Part | # | Part |
|---|---|---|---|
| A | USB 3.0 | E | HDD LED |
| M | USB 2.0 | F | Power button |
| C | Power LED | G | Fan controller |
| D | Mic & Headphones | H | Reset button |
Separating the side panel
Side Panel Removal
Mounting the main board
As 6 stand-offs are mounted by default, insert an additional standoff
according to the type of main board by referring to the mounting position of
the main board, and mount the main board on the case.
Mounting PCI-E(VGA) card
Loosen the screw, separate the PCI cover, mount the graphic card, and fix it
using the screw.
Mounting 2.5” SSD and HDD
2.5″ HDD and SSDs can be installed on the right side of case as shown in the
diagram below.
Mounting the 3.5” and 2.5” HDD
Separate the tooFfree 2.5” and 3.5” combo HDD cage and assemble the HDD or SSD. Mount the assembled HDD on the slot.
Cable Connection
Mounting the top fan
As shown in the picture, install the fan on the top of the case using bolts
Mounting the fan and radiator in the front
sinelisame ‘fer Front Cover Removal and Mount the fan or the radiator on the
mount hole in the front as shown in the figure.
(For liquid-coolers, only products with a hose length of 280 mm or more can be
installed)
