ThermoWorks 292-910 TempTest Blue Thermometer TempTest 2 Blue Thermometer Instruction Manual
- June 16, 2024
- ThermoWorks
Table of Contents
TempTest™ Blue Thermometer & TempTest™ 2 Blue Thermometer
Operating Instructions
INSTRUMENT OPERATION
The instrument is switched on by pressing the Transmit button. The instrument
takes approximately 2 seconds to start up. After this the temperature is
displayed and the instrument continues to measure at its set measurement rate
(default 1 second).
The instrument is now ready for a Bluetooth® connection to a smart device, but
can be used without a wireless connection.
Apply the tip of the probe to the substance, medium or surface to be measured.
The sensor is located at the tip of the probe, therefore the minimum depth
insertion should be 0.12″ (3 mm).
The probe tip is very sharp and can remain hot therefore caution should be
taken when using.
CONNECTION – Use a Bluetooth® enabled iOS or Android™ host device with
compatible app installed to connect to the instrument. When
connecting/disconnecting, the instrument’s amber light flashes rapidly 5
times.
Please Note: No readings are stored in the instrument. When not
connected, the instrument can still be used. Readings are taken and displayed
every 1 second.
TRANSMIT BUTTON FUNCTIONS:
- On – Press to switch the instrument on.
- Measure/Transmit – Press to measure temperature and transmit result via Bluetooth wireless technology (if connected).
- Off – hold down for 3 seconds to switch the instrument off.
LCD INDICATIONS
The LCD automatically rotates to indicate temperatures at the angle the
instrument is being held.
– Indicates a low battery level – see Battery
Replacement section.
- ‘Hi’ – temperature reading is above 572°F
- ‘Lo’ – temperature reading is below –58°F
- ‘AHi’ – instruments ambient is above 122°F
- ‘ALo’ – instruments ambient is below –4°F
- ‘Err’ – sensor fault or open circuit
LED INDICATIONS
The instrument has an amber light located just above the LCD to indicate Bluetooth connection status:
- 5 rapid flashes indicate when connecting or disconnecting.
- A single flash every 10 seconds indicates you are still connected.
- When connected and the Transmit button is pressed, a single flash indicates that the temperature has been transmitted via Bluetooth wireless technology.
SETTINGS – Adjustable via the app and include: °C or °F, Measurement Interval, Auto-off Interval, Sensor Name, and High/Low Alarm levels. All settings are stored in the instrument and are downloaded to the app on connection.
AUTO-OFF – If the instrument is not connected to a smart device or the Transmit button is not pressed within the set Auto-off interval (default 10 minutes) then it will switch off.
BATTERY REPLACEMENT
The low battery symbol will indicate when the batteries need replacing. The
instrument continues to measure accurately but it’s recommended that the
batteries are changed as soon as possible. To replace the batteries, remove
the battery cover on the bottom using phillips screwdriver. Replace the 2 x
AAA batteries ensuring correct polarities. Replace the cover and tighten to
ensure the unit remains waterproof. Do not overtighten.
Please note: the battery cover can only be fitted one way.
INSTRUMENT CLEANING
Clean the entire probe shaft with a probe wipe after each use to prevent bacteria growth. Clean instrument body with a damp, soapy cloth and dry thoroughly. (NOTE: cleaning wipes and solvents containing Isopropyl Alcohol (IPA) may cause damage to the instrument enclosure and display screen, and will void the warranty)
GUARANTEE
This instrument carries a two-year warranty against defects in either
components or workmanship. During this period, products that prove to be
defective will, at the discretion of ThermoWorks, be either repaired or
replaced without charge. This warranty does not apply to probes, where a six-
month period is offered. Full details of liability are available within
ThermoWorks’ Terms & Conditions of Sale at www.thermoworks.com/product-
warranty.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by ThermoWorks is under license.
Google Play and the Google Play logo are trademarks of Google Inc. Android is
a trademark of Google Inc.
Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries. App Store is a service mark of
Apple Inc., registered in the U.S. and other countries.
iOS is a trademark or registered trademark of Cisco in the U.S. and other
countries and is used under license.
| Model | Order Code |
|---|---|
| TempTest Blue | 292-910 |
| TempTest 2 Blue | 292-857 |
SPECIFICATIONS
| Range | –58 to 572°F (–49.9 to 299.9°C) |
|---|---|
| Accuracy | ±0.7°F (±0.4°C) from –58 to 392°F |
(–49.9 to 199.9°C) otherwise ±1.8°F (±1.0°C)
Response| 2-3 sec. (reads to within 1°F of final temperature of an ice
bath in 3 sec.)
Resolution| 0.1°
Battery| 2 x AAA / 1,000 hours
Sensor Type| High-performance Type K thermocouple
Connection| Requires Bluetooth 4.1 or above
Probe| 0.125 dia. x 4.3 L inches
(3.3 dia. x 109 L mm) with reduced tip to 0.06 dia. inches (1.5 dia. mm)
Water Resistance| IP67
Wireless Comm.| Bluetooth 4.0
Environmental Range| –4 to 122°F (–20 to 50°C)
Dimensions| 4.7 H x 1.9 W x 0.7 D inches
(120 H x 47 W x 17 D mm)
Weight| 3.7 oz. (105 g)
Calibration| NIST-traceable certificate included
RADIO CERTIFICATIONS
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotopically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
|
ThermoWorks, Inc.
Utah, U.S.A.
Ph: 801-756-7705 Fax:
801-756-8948
www.thermoworks.com|
---|---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>