ThermoWorks MicroTherma 2K Thermometer Instruction Manual
- June 6, 2024
- ThermoWorks
Table of Contents
MicroTherma 2K
Thermometer
Operating Instructions
INSTRUMENT OPERATION
– Where applicable, connect a probe via the socket located on the front of the instrument. Switch the instrument on and apply the tip of the probe to the substance or medium to be measured. The instrument reading may take a few seconds to stabilize, depending on the nature of the measurement and sensitivity of the probe.
ON/OFF – To turn the instrument on press the ON/OFF button. All display segments will be tested. When turning off, the unit will remember the last settings and restart with the same configuration. The unit is now ready to measure temperature. To turn the instrument off press the ON/OFF button. ‘Saving data’ followed by ‘Product OFF’ will be displayed in the text line.
DISPLAY – The display has two sections. The main section is a 4½-digit temperature display located in the lower half of the viewing area, where measured values are displayed. The other section is a 12-digit alpha/numeric dot-matrix text line, located at the top of the viewing area, above the temperature display. Set-up information and the command prompt will be displayed here.
RESOLUTION – The unit resolution will be 0.1°, within the range ±1999.9° and will be 1° outside of this.
AUTO-OFF – Auto-off is set at 30 minutes. This can be disabled. In ambient measurement mode, the auto-off is fixed at 10 minutes.
AMBIENT MEASUREMENT
– This facility allows the internal CJC temperature of the unit to be
measured. This allows the user to
determine if the unit has sufficiently acclimatized. Acclimatize a nation is
crucial for accurate measurement. Start the unit by pressing and
releasing the ON/OFF button while pressing the HOLD and MAX/MIN buttons. Do
not release the HOLD and MAX/MIN buttons until the software revision is
displayed.
°C/°F – °C or °F is selectable in the Parameter Set-Up Menu.
HOLD – Press the HOLD button to hold the reading. ‘HOLD’ will illuminate in the display. Press again to release the hold.
MAX/MIN – Press the MAX/MIN button to show the max temperature in the dot matrix text line. Press again to show the minimum temperature. Press again to show the T/C type. Max and Min values will be cleared when the instrument changes from °C to °F and vice versa or is switched off. Max/Min values can be cleared in the Parameter Set-up Menu.
TRIM FUNCTION – This function allows a constant temperature offset to be
entered to compensate for thermocouple probe
tolerances. The trim value is selectable in the Parameter Set-Up Menu. The
maximum trim value is ± 4.5°F (2.5°C). The trim value will
be displayed in the text line at start-up if it is not equal to zero.
INTERNAL/EXTERNAL CJC (COLD JUNCTION COMPENSATION)
– The unit will automatically adjust the thermocouple input to allow for
changes in the ambient temperature when the CJC is set to ‘INTERNAL’. Use CJC
‘EXTERNAL’ if the input is being wired through an “ice point reference”. When
using an “ice point reference”,
copper wires must be used from the reference to the MicroTherma input. This is
selectable in the Parameter Set-Up Menu.
UNDER OR OVER RANGE/OPEN CIRCUIT – ‘Range Error’ will be displayed in the text line if the measured temperature is outside the range of the instrument. ‘Range Error’ will also be displayed if the sensor is open circuit.
BUTTON FUNCTION IN THE PARAMETER SET-UP MENU – Press the MODE button to
enter the parameter set-up menu. The parameter and its current setting will be
shown in the text line.
Press the MODE button to move to the next parameter. Use either the HOLD or
MAX/MIN button to change the setting (i.e. Y to N, °C to °F, Internal CJC to
External CJC). When setting display contrast press and hold the HOLD button to
increase contrast (darken the display) and the MAX/MIN button to decrease
contrast (lighten the display). Press both HOLD and MAX/MIN buttons together
to return to the factory default. When adjusting the trim function press the
HOLD button to increase the value and the MAX/MIN button to decrease the
value. Press both HOLD and MAX/MIN buttons together to return to zero trim
value. When all parameters have been scrolled through, ‘End of list’ will be
displayed while the settings are saved. Press the MODE button to enter the
parameter set up menu.
Parameter Set-up Menu List:
Temp in <°C> <°F>
BATTERIES – ‘LO BAT’ indicates that the batteries need replacing as soon as possible. The unit will continue to function but to maintain accuracy new batteries are required. Replace 2x batteries with AAA, 1.5-volt alkaline batteries. If ‘Battery Flat’ is displayed in the text line the instrument has detected that there is insufficient battery voltage left to function correctly. The instrument will shut down and will not measure again until new batteries have been installed.
EMC/RFI – Readings may be affected if the unit is operated within a radio
frequency electromagnetic field strength of approximately 3
volts per meter, but the performance of the instrument will not be permanently
affected.
MODEL
MicroTherma 2K
ORDER CODE
221-092
SPECIFICATIONS
| Range | —328 to 2501°F (-200 to 1372°C) |
|---|---|
| Accuracy | ±0.36°F (+0.2°C), ±1 digit |
| Resolution | 0.1° to 1999.9°, auto-ranging to 1° above |
| Probe | Not included, mini-connector, Type K |
| Battery | 2 x AAA, 1,000 hours |
| Auto-off | 30 minutes |
| Environmental | 32 to 122°F (0 to 50°C) |
| Range | |
| Dimensions | 2.87 W x 5.55 H x 1.38 D inches |
(73 W x 141 H x 35 D mm)
Certificate| NIST-traceable certificate included
GUARANTEE – This instrument carries a two-year warranty against defects
in either components or workmanship. During this period, products that prove
to be defective will, at the discretion of ThermoWorks, be either repaired or
replaced without charge. This warranty does not apply to probes, where a six-
month period is offered. Full details of liability are available within
ThermoWorks’ Terms & Conditions of Sale at
www.thermoworks.com/productwarranty.
For warranty, service, and technical assistance, please contact ThermoWorks’
Technical Support at 801-756-7705 or
email at echsupport@thermoworks.com.
ACCESSORIES/RELATED ITEMS
| |
---|---|---
MicroTherma 2K Meter
& Probe Kit
( Y-221-092)| Carrying Case
(THS-834-100)| Duracell Procell AAA Battery, 4-pack
(PC2400)
P-20-001-02-a
Ref: 547-130 28.01.20
741 E. Utah Valley Dr., American Fork, UT 84003
Ph: 801-756-7705 Fax:
801-756-8948
thermoworks.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>