VIVO STAND-V038W Dual Ultrawide Monitor Desk Mount Instruction Manual

June 16, 2024
Vivo

Dual Ultrawide Monitor Desk Mount
Instruction Manual

STAND-V038W Dual Ultrawide Monitor Desk Mount

SKU: STAND-V038/W

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-v002
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

| help@vivo-us.com
---|---
| www.vivo-us.com
Chat live with an agent!
| 309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

  • NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
  • USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

PACKAGE CONTENTS

VIVO STAND-V038W Dual Ultrawide Monitor Desk Mount -
parts NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

ASSEMBLY STEPS

STEP 1
VIVO STAND-V038W Dual Ultrawide Monitor Desk Mount -
parts1 IMPORTANT NOTE
Monitor mount can be assembled as a Desk Clamp (2a) or Grommet Mount (2b).
Follow steps below for desired mounting method.
STEP 2a – Desk Clamp
Mount Clamp (B) to Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
Secure assembly to desktop by tightening knob on Clamp (B).VIVO STAND-V038W
Dual Ultrawide Monitor Desk Mount - parts2 STEP 2b – Grommet Mount
Using a Phillips screwdriver, remove the screw from Clamp (B) and disassemble. Set Knob (B2) aside. VIVO STAND-V038W Dual Ultrawide Monitor Desk Mount -
parts3Mount Grommet Plate (E) to Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A). Remove adhesive backing from Soft Pad (F) and adhere to Grommet Plate (E).VIVO STAND-V038W Dual
Ultrawide Monitor Desk Mount - parts4Secure assembly to gromment hole in desk using Knob (B2) and Support Plate (G), as shown below. VIVO STAND-V038W Dual Ultrawide Monitor
Desk Mount - parts5STEP 3
Unfold Swivel Arm (C) and extend into one straight line. VIVO STAND-V038W
Dual Ultrawide Monitor Desk Mount - parts6Slide Pole Cable Clip (I) and Swivel Arm (C) onto Pole (A). Secure Swivel Arm (C) in place using 6mm Allen Wrench (T-B). Attach Pole Cap (H) to Pole (A).VIVO STAND-V038W Dual Ultrawide Monitor Desk Mount -
parts7Attach Arm Cable Clips (J) to Swivel Arm (C).VIVO STAND-V038W Dual Ultrawide Monitor Desk Mount -
parts8 STEP 4
Secure VESA Plates (D) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm Screws (M-B). M6 Spacers (M-C) may be required.VIVO STAND-V038W Dual
Ultrawide Monitor Desk Mount - parts9 STEP 5
Slide monitors with VESA Plates (D) onto Swivel Arm (C). Secure VESA Plates (D) in place using M6 Security Nuts (S-B).VIVO STAND-V038W Dual Ultrawide
Monitor Desk Mount - parts10 STEP 6
Manage cables using Arm Cable Clips (J) and Pole Cable Clip (I).VIVO STAND-
V038W Dual Ultrawide Monitor Desk Mount - parts11 ADJUST AS DESIRED
+90° to -90° TILT:
If monitors are sagging or need repositioned, loosen the bolt on the side of the VESA Head (C1) on Swivel Arm (C). Use 6mm Allen Wrench (T-B) to loosen, then adjust. Tighten to secure. . VIVO STAND-V038W Dual Ultrawide Monitor
Desk Mount - parts12180° SWIVEL:
Lighten pull monitors left or right to adjust swivel. VIVO STAND-V038W Dual
Ultrawide Monitor Desk Mount - parts13360° ROTATION:
Lighten pull monitors left or right to adjust swivel. VIVO STAND-V038W Dual
Ultrawide Monitor Desk Mount - parts14ADJUST MONITOR HEIGHT
To level monitors, remove M6 Security Nuts (S-B) and tighten or loosen adjustment screws using 3mm Allen Wrench (T-A). Once level, fasten M6 Security Nuts (S-B) back into place.VIVO STAND-V038W Dual Ultrawide Monitor Desk
Mount - parts15 Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 11/29/2023
REV1
Open Monday – Friday 7:00am – 7:00pm CS T, our dedicated support team can off er immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

| 309-278-5303| AVG. RESOLUTION TIME (within o  ice hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within o  ice hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within o ice hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Vivo User Manuals

Related Manuals