Kruger Matz KM2011 Car Radio Owner’s Manual

: June 16, 2024
: Kruger Matz

Kruger Matz KM2011 Car Radio Owner’s Manual

Safety precautions

DO NOT operate this device while driving, as this may lead to a traffic
Stop the car before performing any operations! Do not perform any activities that may distract from cautious driving, such as managing playlist.
Do not raise the volume level too much, as this will block outside sounds, making driving
Clean with soft, slightly damp cloth
When inserting battery, please note the correct
If the remote is not used for an extended period of time, remove the battery to prevent possible damage from battery

Hearing safety

Listen at a moderate volume. Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So after prolonged listening, what sounds “normal” can actually be loud and harmful to your To guard against this, set your volume to a safe level before your hearing adapts and leave it there.
Listen for reasonable periods of time:
Prolonged exposure to sound, even at normally “safe” levels, can also cause hearing
Be sure to use your equipment reasonably and take appropriate breaks

Notes on external memory

Do not store memory drive inside the vehicle where it will be exposed to direct sunlight, high temperatures, high humidity or corrosive substances.
Make sure the connected USB drive does not obstruct unhindered vehicle
Memory drive may not function properly in extremely high/low temperature
The producer does not guarantee capability with every external
Files protected against copying (copyright protection) may not be
In some cases, start of the playback may be delayed, but does not constitute of any malfunction or damage.
Producer does not claim any liability for any data
Do not unplug external memory while Change the sound source before disconnecting the memory drive from this device.

PRODUCT DESCRIPTION

Front

Display
Power/mode/end call button
Search stations button
BAND/pick up call button
Volume control/change option knob
IR LED
Back/Previous track button
Clock button
Next/Next Track Button
First program/pause button

Back

Second program/INT mode button
Third program/repeat button
Fourth program/random playback button
Fifth program button/previous folder
Sixth program button/next folder
AUX input
MicroSD Card slot
USB charging socket
USB playback socket
Antenna input
RCA outputs
ISO wiring socket
Fuse
Band change/pick up call button
Mode change /end call button
Program/function buttons
Mute sound
Graphic equalizer
Clock button
Automatic scanning of radio stations
Volume down
Settings button
Volume up
Previous track
Play/pause
Next track

CONNECTION

Connect the radio plug from the car to the ISO socket of the radio (adapters for different car models are sold separately).

Socket B

Rear right speaker +
Rear right speaker
Front right speaker —
Front left speaker +
Front left speaker —
Rear left speaker +
Rear left speaker —

Socket A

Unused
Unused
Power B+ – 12 V power supply
Audio antenna B+ – antenna power
Unused
ACC +12V — 12 V after ignition
GROUND – grounding

OPERATION

Press the power button to turn the radio on. Press and hold the power button to turn the radio off.
Press the MODE button to change the playback
Press the adjustment knob to open the settings. Use the knob to change the settings. After 3 seconds of inactivity, the radio will return to the last playback mode.

Setting the clock

Turn on the
Press and hold the clock The hour indicator will start flashing. Use the knob to set the time.
Press the knob or clock button to change to minutes
Use the dial to set the
Press and hold the clock button to confirm the time settings, or wait 5

Radio

Radio is the default mode when you first turn it
To automatically search for radio stations, press the AM
To set the frequency manually, press and hold the next or previous song button. The message “HAND” will appear on the Use the next and previous track buttons to set the frequency. After 3 seconds of inactivity, the radio will display the “AUTO” message, and pressing the next or previous song button will automatically change the frequency.
To assign a set frequency to one of the lower six buttons, press and hold the selected program button.
A separate set of saved radio stations can be assigned to each FM band (FM1, FM2, FM3, AM1, AM2).
To change the band, press the BAND Each press will switch to another band.

Playing from a microSD card or USB drive
When you connect a USB drive (e.g. a flash drive) or a microSD card (the card locks in the socket, insert it with pins facing the display), the radio will automatically switch to the correct mode. If this does not happen, switch the mode manually using the MODE button.

Press and hold the BAND button to display information about the song being played. Press the BAND button, then use the rotary knob to skip to the selected song.
Press the pause button to pause or resume the
Press the INT mode button to activate In this mode, the songs will play for the first 10 seconds.
Press the repeat button to change the repeating mode: repeating a single song (RPT ONE), repeating songs from a folder (RPT DIR), repeating all songs (RPT ALL). If there is an RPT message on the display, one of the first two modes is active (the default repetition mode is repeating all songs and is not indicated by an RPT message).
Press the random play button to enable or disable random play mode. When you turn on the mode, an RDM message will appear on the display.

Playing from AUX

Connect the 5 mm plug of the external device to the AUX socket.
Change the mode to AUX IN using the MODE
Use the external device to control the playback of the

Bluetooth playback

Press the MODE button to change the playing mode to A “BT OFF” message will appear on the display, indicating that the radio is ready for pairing.
Turn on Bluetooth on your phone and search for nearby Connect to the CAR BT. After a while, the message “BT LINK” will appear on the display, indicating that the connection has been established.
You can control the music played from the phone on the Start the music player on your phone. From the radio you can scroll through songs using the previous and next track buttons, and pause and resume playback using the pause button. Bluetooth music control can only be done in BT LINK mode.
When your phone is connected with the radio, the call management function is also activated. When you have an incoming call, the music will stop and a phone number will appear on the display. To answer, press the pick up call To end or reject the call, press the end call button.
If your phone is paired with the radio, simply turn on Bluetooth on your phone and make sure that your phone connects to the radio. The radio does not need to be switched to BT LINK mode. When the connection is established, the message “BT LINK” will appear on the radio, and the music in the selected mode will continue

Phone app

Download and install the SmartBT iPlug app from the Play Store or AppStore (or scan the ǪR code).
Connect the app via Bluetooth (repeat steps from previousparagraph)
Open the After a successful connection, the radio can be controlled from the application.
AM preset memory: 12

SPECIFICATION

MAIN FEATURES

Backlight: red
Bluetooth: yes
Phone app: yes
Phone calls management: yes
Size: 1 DIN
Equalizer: Jazz / Pop / Rock / Classic

TECHNICAL PARAMETERS

Maximum power: 4 x 25 W
S/N ratio: 45 dB
Channel separation: 43 dB
Voltage: 8 – 14.4 V
Mounting depth: 12 cm
Supported file formats: MP3, WMA

RADIO TUNER

FM frequency range: 87,5 – 108 MH
FM preset memory: 18
AM preset memory: 12

INPUTS/OUTPUTS

RDS: yes
USB ports: 1 x playing / 1 x charging
microSD port
AUX: 3,5 mm
Frequency scan: automatic/manual
2x RCA output
Antenna input
ISO harness socket

IN SET

Main unit
ISO plug
Halfsleeve
Mounting accessories

PHYSICAL PARAMETERS

Weight: 450 g
Dimensions: 187 x 57 x 135 mm

Radio	Frequency	Max. output power
Bluetooth	2400 – 2450 MHz	4,2 dBm

Lechpol Electronics Leszek Sp.k. hereby declares that radio KM2011 is consistent with directive 2014/53/UE.Full text of the EU Declaration of Conformity is available at following Internet address: www.lechpol.pl.

English

Correct Disposal of This Product

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes
Należy zwrócić szczególną uwagş, aby wszystkie połączenia były wykonane prawidłowo. at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled
Odwrotne podłączenie doprowadzi do zwarcia i uszkodzenia.
waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k.,ul. Garwolińska 1, 08-400 Miştne.