Cell2 Raiden DC Lightbar 1676mm 66 RBK Instruction Manual
- June 16, 2024
- Cell2
Table of Contents
Cell2 Raiden DC Lightbar 1676mm 66 RBK
Product Information
Specifications
- Model: CE – Single / Dual Colour – ECE R65/R10
- Version: v.1.0
Power & CAN Cable
- Route power wires to the vehicle firewall towards the battery, preferably using a factory pass-through. If drilling a hole is required, please ensure there are no factory components in the area to be drilled.
- Install a fuse (user-supplied) to the end of the RED wire and connect it to the battery. (for correct fuse rating, refer to the Lightbar Specs.)
- Connect the BLACK wire to the vehicle chassis-ground next to the battery. NOTE: Ensure that all wires of the power cable are firmly connected to the power source.
- Route CAN wires towards the CAN Controller Module.
- Connect 2 CANBus signal and Shield wires to respective counterparts on the 6-pin connector harness of the CAN Controller Module. (Refer to CAN Controller Module Installation and Operation Manual)
Function Wires (Input)
Connect each function wire according to its function.
ECE R65 WARNING MODE
Activate ECE R65 Warning Mode by applying the GREEN-WHT wire to +VDC. All
corner lightheads will display Double Flash [2Hz] simultaneously.
FAQ
-
Q: Can I use the power wire(s) as the lightbar activation switch?
A: No, it is not recommended to use the power wire(s) as the lightbar activation switch. Use only the function wire(s) to switch and activate the lightbar. -
Q: What should I do before activating any function wire(s)?
A: Ensure that the power wire(s) are properly connected before activating any function wire(s). Faulty connections may cause the lightbar to malfunction and/or reset to its default settings. -
Q: Can I use a high-pressure power washer to clean the lightbar?
A: No, using a high-pressure power washer to clean the lightbar may damage it and void its warranty.
WIRING & FUNCTIONS
(CE – Single / Dual Colour – ECE R65/R10)
Proper installation of the product requires the installer to have a good
understanding of automotive electronics, systems and procedures. Different
applications may require different functions. For optimum efficiency, it is
highly recommended to determine, configure and test the required functions
before installation.
LIGHTBAR WIRING
NOTE: All function wires (Input) are activated by applying +VDC
continuously.
[Px] = Order of Precedence. When more than one wire are activated at the
same time, the wire with the higher precedence will override / affect the
performance of the lower precedence wire. P1 being the highest order.
*Actual approval is based on the configuration of the model ordered.
WARNING
- DO NOT USE THE POWER WIRE(S) AS THE LIGHTBAR ACTIVATION SWITCH. USE ONLY THE FUNCTION WIRE(S) TO SWITCH AND ACTIVATE.
- ENSURE THE POWER WIRE(S) ARE PROPERLY CONNECTED BEFORE ACTIVATING ANY FUNCTION WIRE(S).
- FAULTY CONNECTIONS MAY CAUSE THE LIGHTBAR TO MALFUNCTION AND / OR RESET TO ITS DEFAULT SETTINGS.
- DO NOT USE A HIGH-PRESSURE POWER WASHER TO CLEAN YOUR LIGHTBAR; THIS MAY DAMAGE YOUR LIGHTBAR AND VOID ITS WARRANTY.
POWER & CAN CABLE
-
Route power wires to the vehicle firewall towards the battery, preferably using a factory pass-through. If drilling a hole is required, please ensure there are no factory components in the area to be drilled.
-
Install a fuse (user-supplied) to the end of the RED wire and connect it to the battery. (for correct fuse rating, refer to the Lightbar Specs.)
-
Connect the BLACK wire to the vehicle chassis-ground next to the battery.
NOTE: Ensure that all wires of the power cable are firmly connected to the power source. -
Route CAN wires towards the CAN Controller Module.
-
Connect 2 CANBus signal and Shield wires to respective counterparts on the 6-pin connector harness of the CAN Controller Module. (Refer to CAN Controller Module Installation and Operation Manual)
FUNCTION WIRES (Input)
Connect each individual function wire according to its function.
ECE R65 WARNING MODE
Activate ECE R65 Warning Mode by applying the GREEN-WHT wire to +VDC. All
corner lightheads will display Double Flash [2Hz] simultaneously.
WARNING MODE 1
Activate Warning Mode 1 by applying the ORANGE-WHT wire to +VDC. All warning
lightheads will display Pulsing Flash Pattern simultaneously.
WARNING MODE 2
Activate Warning Mode 2 by applying the YELLOW-WHT wire to +VDC. All warning
lightheads will display Double Flash [2Hz] simultaneously.
CRUISE MODE
Activate Cruise Mode by applying the RED-WHT wire to +VDC. All warning
lightheads will be activated in low power steady-burn.
FULL FRONT FLOOD
Activate Full Front Flood by applying +VDC to the YELLOW wire. All Front
Middle & Front Corner Lightheads will display in High Power steady-burn.
NOTE: If the lightbar is equipped with Dual Color warning lighthead,
Color 2 will be displayed.
TAKE-DOWN LIGHTS
Activate the Take-Down Light in High Power steady-burn by applying the PURPLE
wire to +VDC. By default, Take-Down Lights are set at the second lightheads
from the center of the lightbar.
NOTE: If the lightbar is equipped with Dual Color light heads as Take-
Down light, Color 2 will be displayed.
ALLEY (CORNER) LIGHT
Activate Alley and Corner warning lightheads in High Power steady-burn by
applying
- GREEN wire to +VDC for Left Alley & Corner Light.
- BLUE wire to +VDC for Right Alley & Corner Light.
NOTE: If the lightbar is equipped with Dual Color lightheads, Color 2 will be displayed.
FLASHING TAKE-DOWN & ALLEY LIGHT
Activate Flashing Take-Down & Alley Light in Left alternating Right by
applying the GREY wire to +VDC. By default, Take-Down Lights are set at the
second lightheads from the center of the lightbar.
NOTE: If the lightbar is equipped with Dual Color lightheads, Color 2
will be displayed.
TRAFFIC ARROW
Activate rear Traffic Arrow function by applying
- WHITE wire to +VDC for Left Arrow
- WHITE-BLK wire to +VDC for Right Arrow
- Above 2 wires together to +VDC for Centre-out Arrow
NOTE: If the lightbar is equipped with a color warning lighthead, Color 2 will be displayed.
REAR WIG-WAG
Activate rear Wig-Wag by applying the GREY-WHT wire to +VDC. Rear light heads
will display Single Flash [2Hz], alternating side-by-side.
NOTE: If the lightbar is equipped with a color warning light head, Color
2 will be displayed.
WARNING CUT-OFF
Deactivate warning light heads in each respective area by applying
- PURPLE-WHT wire to +VDC for Front Cut-off.
- BLUE-WHT wire to +VDC for Rear Cut-off.
- ORANGE wire to +VDC for Corner (Alley) Cut-off.
NOTE: Warning Cut-off does not affect the Take-Down Light, Alley Light and Traffic Arrow function.
LOW POWER OPERATION / DIM FUNCTION
Activate Low Power Operation by continuously applying +VDC to the RED wire.
FUNCTION WIRES (Output)
Connect each function wire according to its function.
WARNING MODE SIGNAL
Connect the BROWN-WHT wire to an apparatus that needs to be turned ON with
Warning Modes (e.g. Unlocking Siren Interlock); a 250mA signal is output
whenever GREEN-WHT, YELLOW-WHT and/or ORANGE-WHT wire is activated.
CONTROL PANEL SIGNAL INDICATOR (REAR LIGHTHEADED)
Connect the BROWN wire to the display signal input of a compatible Control
Panel to display the current rear lighthead activity.
AUTO-DIMMING LIGHT SENSOR
If the lightbar is equipped with an Auto-Dimming Light Sensor, Low Power Operation will automatically activate when the ambient brightness is below the set value (e.g. night time) and deactivate once prior condition is removed. The Auto-Dimming Light Sensor takes precedence over all other function wires.
PC PROGRAMMING
All function wires may be customized and re-programmed to the user’s preference for
- Light Sensor dimming values,
- Lighthead flash delay/flash groups/phases / flash patterns/colors,
- Low power %,
- Traffic arrow patterns,
- Output signal,
- Wire precedence (priority),
- and etc.
RAIDEN Lightbar Configuration Tool is a piece of software that can be used to
program your RAIDEN lightbar quickly and intuitively. Download software from
the support utility site via this link:
https://service.juluen.com.tw/Utility
NOTE: For more instructions, refer to [Software Manual] from the support
utility site.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>