SILVER STAR SS9151SC Pluto Beam User Manual

: June 9, 2024
: SILVER STAR

Table of Contents

PRODUCT
- TECHNICAL SPECIFICATIONS
Safety Notes
INSTALLATION
FUNCTIONS AND SETTINGS
- DISPLAY OPERATION
- Menu Map
USING A DMX512 CONTROLLER
- DMX CONTROL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SILVER STAR SS9151SC Pluto Beam

PRODUCT

TECHNICAL SPECIFICATIONS

Type	SS9151SC
LED colors	130W Cool White LED
Power	200W
Voltage Range	AC100~240V,50/60Hz
Protection	IP20
Operation Temperature	0℃~45℃
Dimensions	330x249x521mm
Weight	15kg

Safety Notes

IMPORTANT

This product must be installed by a qualified professional.
In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.

CAUTION

Make sure that the available voltage is not higher than stated on the rear panel.
Do not touch the power cables if your hands are wet.
The earth wire must always be connected to the ground. Therefore it is essential to connect the yellow/green conductor to earth.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time. The electric connection, repairs and servicing must be carried out by a qualified employee.
Always disconnect power input cable to completely remove power from unit when not in use or before cleaning or servicing the fixture.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)! The surface of the product’s casing can reach up to 70° C (158° F) during operation. Avoid contact by persons and materials. Do not install the product in a location where there is a risk of accidental contact. Allow the product to cool for at least 10 minutes before handling.
For replacement use lamps and fuses of same type and rating only.
Please protect the fixture and avoid destroy during transport and installation. If there is any damage to the coating, the shell may be corroded.
When hanging lamps and lanterns, it is necessary to verify that facilities and hooks can bear at least 10 times the weight of lamps and lanterns.
Fix the safety rope at the correct holes only. Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
The maximum ambient temperature 45°C must never be exceeded. Do not operate the product if the ambient temperature (Ta) exceeds 45° C (115° F).
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective.

Electrical Warning

The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person
For replacement use lamps and fuses of same type and rating only.
The lens has to be replaced when it is obviously damaged, so that its function is impaired, e. g. due to cracks or deep scratches!

Keep the product well away from flammable materials

Keep all combustible materials (e.g. fabric, wood, paper) at least 500 mm (20 in.) away from the product.
Ensure that there is free and unobstructed airflow around the product. Provide a minimum clearance of 150 mm (6 in.) around fans and air vents.
Do not illuminate surfaces within 3 m (10 ft.) of the product.
Do not install a fuse that has a higher rating than the one originally installed in the product. Do not bypass fuses.
Do not stick filters, masks or other materials onto optical components.
If the fixture seems to be abnormally hot, shows signs of melting or emits smoke, disconnect the fixture from power immediately and allow it to cool. Do not touch the fixture without heatproof safety gloves. Keep the fixture well away from combustible and flammable materials.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK – MAY INDUCE BLINDNESS!

Do not point the front of the fixture towards the sun or other strong light sources. The front lens focuses and concentrates light just like a magnifying glass. Strong light can cause internal damage to the fixture, melting components or starting an internal fire within seconds.

To avoid problems from strong light sources:

Do not expose the front of a fixture to sunlight or any other strong light source. Avoid pointing other high-powered beam lights directly at the fixture.
Do not focus a light beam from one lighting fixture directly towards another.
For outdoor applications during daylight, make sure that the front face of any fixture is shielded or points away from the sun, even when not in use.
Do not expose the product to heat (from other lighting fixtures for example).

INSTALLATION

MOUNTING

Truss installation

Keep all combustible materials (e.g. fabric, wood, paper) at least 500 mm (20 in.) away from the product.
For overhead use, always install a safety cable that can hold at least 10 times the weight of the fixture.
For overhead installation, the fixture must be always secured with a safety wire that can bear at least 10 times the weight of the fixture；
Secure the fixture with a safety cable through the rear safety eye and truss as shown..
Ensure that the structure (truss) to which you are attaching the fixture is secure.

POWER CONNECTIONS

This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.

Data network requirements

Connect the DMX512 controller to the units in series. A DMX 512 data link is required in order to control the fixture via DMX. The fixture has 3/5-pin XLR connectors for DMX data input and output.
Each unit has 13 DMX channels so the DMX Addresses should increase by increments of 1， (Nx1)+1，(Nx2)+1，(Nx3)+1…
Any DMX address in the range from 001 to 512 may be used.
Connect the DMX-output of the first fixture in the DMX chain with the DMX-input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω resistor between Signal (–) and Signal (+) into a 3/5-pin XLR-plug and plug it in the DMX-output of the last fixture.

FUNCTIONS AND SETTINGS

DISPLAY OPERATION

Up: Scroll ‘Up’ through the menu list or increase the value of the current function.
Down: Scroll ‘Down’ through the menu list or decrease the value of the current function.
Left(Back)：Scroll through the main menu.
Right(Enter)：Enter the currently selected menu or confirm the current function value.

ADDRESS	001 – 512	DMX address setting
PERSON	BASIC	Use the menu to select desired channel mode

STANDARD (Default)
EXTEND
SY
RUNMODE| DMX512 (Default)| Select Signal Default: DMX512
CUSTOM1-2 Set up get into EDIT MENU edit
AUTO
CUSTOM1
CUSTOM2
OPTION| ****

PAN INVERT

Select ON Blackout delay 3s

ON
DIMMER| DIM4(Default)| Dimming curves DIM1 (fast) to DIM4
**| DIM3| (slow)
**| DIM2|
**| DIM1|
**| OFF|
LED PWM| 1200Hz (Default)| Sets the PWM frequency
**| 2000Hz|
**| 2400Hz|
**| 4000Hz|
**| 6000Hz|
**| 25000Hz|
DMX ERROR| SAVE (Default)| Hold after loss of DMX signal
**| BLACK| Blackout after loss of DMX signal
DISPLAY INVERT| OFF(Default)| Display reverse off
**| ON| Display reverse on
DISPLAY TIME| On| Display backlight always on
**| 30s| Display light 30s
**| 1min(Default)| Display light 1min
**| 2min| Display light 2min
DISPLAY LOCK| OFF| Locks display (passcode is
<UP

,, , ) ****| **ON(Default)**| **LOAD PARA**| **NO**| Upload data ****| **YES**| Not upload data SETTING| RECOVERY| ****| Restore default factory settings. CLEAN EDIT1| ****| Clean customer self-editing scene 1 CLEAN EDIT2| ****| Clean customer self-editing scene 2 WDMX HIDE| YES| Hide wireless mode WDMX reset and signal hide and the default is wired mode only NO PT ENCODER| OFF| XY Encoder switch.

OFF is close; ON is open.

All passwords of this product are , ,, , )

USING A DMX512 CONTROLLER

DMX CONTROL

CH.6CH.8CH.90-255

| BASIC

（ 13CH)

| STANDARD

（ 15CH)

| Extend

(18CH)

| Value| Function|
---|---|---|---|---|---|---
| CH.1| CH.1| CH.1| 000-255| PAN 0-540°|
| –| CH.2| CH.2| 000-255| PAN FINE|
| CH.2| CH.3| CH.3| 000-255| TILT 0-270°|
| –| CH.4| CH.4| 000-255| TILT FINE|
| CH.3| CH.5| CH.5| 000-255| PT Speed|
| CH.4| CH.6| CH.6| COLOUR WHELL9+1|
| 000-007| WHITE|
| 008-013| COLOR1|
| 014-019| COLOR2|
| 020-025| COLOR3|
| 026-031| COLOR4|
| 032-037| COLOR5|
| 038-043| COLOR6|
| 044-049| COLOR7|
| 050-055| COLOR8|
| 056-063| COLOR9|
| 064-191| COLOR WHELL10-360°|
| 192-222| COLOR WHELL1 RAINBOW EFFECT(SPEED 100%→1)|
| 223-224| STOP|
| 225-255| COLOR WHELL1 RAINBOW EFFECT(SPEED 1→100%)|
| –| –| CH.7| 000-255| 000-255|
| ****

CH.5

| ****

CH.7

| ****

CH.8

| FIXED GOBO WHEEL14+1|
| 0-10| WHITE|
| 11-17| FIXED GOBO 1|
| 18-24| FIXED GOBO 2|
| 25-31| FIXED GOBO 3|
| 32-38| FIXED GOBO 4|
| 39-45| FIXED GOBO 5|
| 46-52| FIXED GOBO 6|
| 53-59| FIXED GOBO 7|
| 60-66| FIXED GOBO 8|
| 67-73| FIXED GOBO 9|
| 74-80| FIXED GOBO 10|
| 81-87| FIXED GOBO 11|
| 88-94| FIXED GOBO 12|
| 85-102| FIXED GOBO 13|
| 103-110| FIXED GOBO 14|
| 111-118| FIXED GOBO 1 SHAKE (SPEED 1 — > 100%)|
| 119-126| FIXED GOBO 2 SHAKE (SPEED 1 — > 100%)|
| 127-134| FIXED GOBO 3 SHAKE (SPEED 1 — > 100%)|
| 135-142| FIXED GOBO 4 SHAKE (SPEED 1 — > 100%)|
| 143-150| FIXED GOBO 5 SHAKE (SPEED 1 — > 100%)|
| 151-158| FIXED GOBO 6 SHAKE (SPEED 1 — > 100%)|
| 159-166| FIXED GOBO 7 SHAKE (SPEED 1 — > 100%)|
| 167-174| FIXED GOBO 8 SHAKE (SPEED 1 — > 100%)|
| 175-182| FIXED GOBO 9 SHAKE (SPEED 1 — > 100%)|
| 183-190| FIXED GOBO 10 SHAKE (SPEED 1 — > 100%)|
| 191-198| FIXED GOBO 11 SHAKE (SPEED 1 — > 100%)|
| 199-206| FIXED GOBO 12 SHAKE (SPEED 1 — > 100%)|
| 207-214| FIXED GOBO 13 SHAKE (SPEED 1 — > 100%)|
| 215-222| FIXED GOBO 14 SHAKE (SPEED 1 — > 100%)|
| 223-230| WHITE|
| 231-238| STATIC GOBO POSITIVE WATER EFFECT (SPEED 100 — > 1%)|
| 239-246| STOP WATER EFFECT|
| 247-255| STATIC GOBO REVERSE WATER EFFECT (SPEED 1 — > 100%)|
| RAINBOW Insert effect wheel|
CH.7| CH.9| CH.10| RAINBOW DISC ROTATION|
0-10| Rotation STOP|
11-127| RAINBOW Insertion CW Rotate Slow to Fast|
128-138| Rotation STOP|
139-255| RAINBOW Insertion CCW Rotate Fast to Slow|
CH.8| CH.10| CH.11| PRISM1|
0-10| WHITE|
11-145| PRISM INSERT AND ADJUST THE ANGLE (0 —> 360°)|
146-150| STOP|
151-200| PRISM INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)|
201-205| STOP|
206-255| PRISM INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)|
CH.9| CH.11| CH.12| PRISM2|
0-10| WHITE|
11-145| PRISM INSERT AND ADJUST THE ANGLE (0 —> 360°)|
146-150| STOP|
151-200| PRISM INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)|
201-205| STOP|
206-255| PRISM INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)|
CH.10| CH.12| CH.13| 0-255| FOCUS|
–| –| CH.14| 0-255| FOCUS FINE|
CH.11| CH.13| CH.15| 0-255| DIMMER|
–| –| CH.16| 0-255| DIMMER FINE|
CH.12| CH.14| CH.17| STROBE|
0-9| NO FUNCTION|
10-99| STROBE（FROM SLOW TO FAST）|
100-109| NO FUNCTION|
110-179| LIGHTNING STROBE|
180-189| NO FUNCTION|
190-255| RANDOM SROBE|
CH.13| CH.15| CH.18| CONTROL( EXECUTE AFTER 3 SECONDS)|
000-010| NO FUNCTION|
011-020| PAN/TILT BLACK ACTIVATED|
021-030| PAN/TILT BLACK DEACTIVATED|
031-040| PAN INVERT|
041-050| TILT INVERT|
051-060| PAN/TILT INVERT OFF|
061-070| STUDIO|
071-080| POWER|
081-090| LIVE|
091-100| DIM4|
101-110| DIM3|
111-120| DIM2|
121-130| DIM1|
131-140| DIM0|
141-150| 1200Hz|
151-160| 2000Hz|
161-170| 2400Hz|
171-180| 4000Hz|
181-190| 6000Hz|
191-200| 25000Hz|
201-210| ALL RESET|
211-220| XY RESET|
221-230| COLOR GOBO SYSTEM RESET|
231-240| FOCUS RESET|
241-255| PRISM RESET|
SY (16CH)| VALUE| FUCTION
CH.1| COLOUR WHELL9+1
000-007| WHITE
008-013| COLOR1
014-019| COLOR2
020-025| COLOR3
026-031| COLOR4
032-037| COLOR5
038-043| COLOR6
044-049| COLOR7
050-055| COLOR8
056-063| COLOR9
064-191| COLOR WHELL10-360°
192-222| COLOR WHELL1 RAINBOW EFFECT(SPEED 100%→1)
223-224| STOP
225-255| COLOR WHELL1 RAINBOW EFFECT(SPEED 1→100%)
CH.2| STROBE
0-3| NO LIGHT
4-103| STROBE（ FROM SLOW TO FAST）
104-107| NO FUNCTION (100% light)
108-207| LIGHTNING STROBE
208-212| NO FUNCTION (100% light)
213-251| RANDOM SROBE
252-255| NO FUNCTION (100% light)
CH.3| 0-255| DIMMER
CH.4| FIXED GOBO WHEEL14+1
0-3| NO FUNCTION (100% light)
4-7| FIXED GOBO 1
8-11| FIXED GOBO 2
12-15| FIXED GOBO 3
16-19| FIXED GOBO 4
20-23| FIXED GOBO 5
24-27| FIXED GOBO 6
28-31| FIXED GOBO 7
32-35| FIXED GOBO 8
36-39| FIXED GOBO 9
40-43| FIXED GOBO 10
44-47| FIXED GOBO 11
48-51| FIXED GOBO 12
52-55| FIXED GOBO 13
56-59| FIXED GOBO 14
60-72| NO FUNCTION
72-113| STATIC GOBO POSITIVE WATER EFFECT (SPEED 100 — > 1%)
114-117| STOP WATER EFFECT
118-159| STATIC GOBO REVERSE WATER EFFECT (SPEED 1 — > 100%)
160-166| FIXED GOBO 2 SHAKE (SPEED 1 — > 100%)
167-172| FIXED GOBO 3 SHAKE (SPEED 1 — > 100%)
173-179| FIXED GOBO 4 SHAKE (SPEED 1 — > 100%)
180-185| FIXED GOBO 5 SHAKE (SPEED 1 — > 100%)
186-191| FIXED GOBO 6 SHAKE (SPEED 1 — > 100%)
192-198| FIXED GOBO 7 SHAKE (SPEED 1 — > 100%)
199-204| FIXED GOBO 8 SHAKE (SPEED 1 — > 100%)
205-211| FIXED GOBO 9 SHAKE (SPEED 1 — > 101%)
212-217| FIXED GOBO 10 SHAKE (SPEED 1 — > 101%)
218-223| FIXED GOBO 11 SHAKE (SPEED 1 — > 101%)
224-230| FIXED GOBO 12 SHAKE (SPEED 1 — > 101%)
231-236| FIXED GOBO 13 SHAKE (SPEED 1 — > 101%)
237-243| FIXED GOBO 14 SHAKE (SPEED 1 — > 101%)
244-255| NO FUNCTION
CH.5| PRISM INSERTION （ 16 Prism ）
0-127| WHITE
128-255| 16 Facet Prism INSERTION
CH.6| PRISM ROTATION （ 16 Prism ）
0-127| PRISM ADJUST THE ANGLE (0 —> 360°)
128-190| PRISM POSITIVE ROTATION (SPEED 100% —> 1)
191-192| STOP
193-255| PRISM REVERSE ROTATION (SPEED 1 —> 100%)
CH.7| RAINBOW EFFECT WHEEL
0-10| WHITE
11-145| ANIMATION INSERT AND ADJUST THE ANGLE (0 —> 360°)
146-150| STOP
151-200| ANIMATION INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)
201-205| STOP
206-255| ANIMATION INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)
CH.8| PRISM EFFECT ( Linear Prism ）
0-10| WHITE
11-127| PRISM INSERTION
128-191| ANIMATION INSERT AND LEFT ROTATION (SPEED 100% —> 1)
192| STOP
193-255| ANIMATION INSERT AND RIGHT ROTATION (SPEED 1 —> 100%)
CH.9| 0-255| FOCUS
CH.10| 0-255| PAN
CH.11| 0-255| PAN FINE
CH.12| 0-255| TILT
CH.13| 0-255| TILT FINE
CH.14| FUNCTION
000-010| NO FUNCTION
011-020| PAN/TILT BLACK ACTIVATED
021-030| PAN/TILT BLACK DEACTIVATED
031-040| PAN INVERT
041-050| TILT INVERT
051-060| PAN/TILT INVERT OFF
061-070| STUDIO
071-080| POWER
081-090| LIVE
091-100| DIM4
101-110| DIM3
111-120| DIM2
121-130| DIM1
131-140| DIM0
141-150| 1200Hz
151-160| 2000Hz
161-170| 2400Hz
171-180| 4000Hz
181-190| 6000Hz
191-200| 25000Hz
201-255| NO FUNCTION
CH.15| RESRT
000-025| UNUSED RANGE
26-76| EFFECTS RESET
77-127| PAN/TILT RESET
128-255| COMPLETE RESET
CH.16| LAMP CONTROL
0-25| UNUSED RANGE
26-100| LAMP OFF
101-255| LAMP ON