CARRO CES525B5L-FM Indoor Outdoor Flush Mount Smart Ceiling Fan Instruction Manual
- June 16, 2024
- CARRO
Table of Contents
- CARRO CES525B5L-FM Indoor Outdoor Flush Mount Smart Ceiling Fan
- SAFETY PRECAUTIONS
- Fan Diagram
- Package Contents & Tools
- Installation Instructions
- Remote Control Instructions
- Connecting to the Carro Home App
- Connecting to Smart Devices
- Troubleshooting
- Care & Cleaning
- FCC Statement
- Basic Product Specifications
- Questions
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CARRO CES525B5L-FM Indoor Outdoor Flush Mount Smart Ceiling Fan
SAFETY PRECAUTIONS
-
Before you begin installing the fan, shut the power off at the circuit breaker of the fuse box.
-
Make sure that all electrical connections are by National Electrical Code, ANSI/NFPA 70 and local codes. Hire a licensed electrician if you are unfamiliar with installing electrical wiring.
-
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 2.1 m (7 feet) from the floor and 18 inches from the tip of the blades to the wall.
-
The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 pounds. Use only U.L. listed outlet boxes marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or less”.
-
Before and after you install the fan, make sure that all mounting components are secured to prevent the fan from falling.
-
Do not insert anything into the fan blades while the fan is operating.
-
To change the direction of the rotation of the blades, the fan must be in operation mode.
-
All set screws must be checked and retightened where necessary before installation.
-
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.
-
The splices after being made should be turned upward and pushed carefully up into the outlet box. Conductor wiring identified as grounded is to be connected to a grounded conductor of power supply. Conductor wiring identified as an ungrounded conductor is to be connected to an ungrounded conductor. Conductor wiring identified for equipment grounding is to be connected to an equipment-grounding conductor.
-
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
This product is suitable for use in damp locations.
-
CAUTION: Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
-
WARNING : To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked ”Acceptable for Fan Support of 15.9 kg (35 lbs) or less” and use mounting screws provided with the outlet box.
-
CAUTION: To reduce the risk of injury, use only the screws provided with the outlet box
in conjunction with the lock washers. -
WARNING: To reduce the risk of personal injury, do not bend the blade bracket when installing the brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
-
CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light kit.
-
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with a general use, non-dimmable, single gang, isolating wall control/switch.
-
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solidstate speed control device.
-
NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care are factors which cannot be built into this product. These factors must be supplied by the person (s) installing, caring for and operating the unit.
-
CAUTION: T he light source is designed for this specific application and can overheat if serviced by untrained personnel. If any servicing is required, the product should be returned to an authorized service facility for examination or repair.
Fan Diagram
Package Contents & Tools
Tools & Materials Required
Package Contents
Before installing, please check to make sure you have received all the necessary components for installation.
Installation Instructions
Installation: Fan Blades
WARNING: To avoid serious injury or death, turn off the power at the circuit breaker before installing the fan.
-
Install the Fan Blades
-
Locate 15-blade attachment screws in the hardware pack. Secure each blade to the blade bracket using blade screws as shown in Fig 1.1.
-
Fig 1.2 is the schematic diagram of the installed fan blade bracket. Repeat these steps for the remaining blades. Make sure all the screws are firmly tightened.
Install the Blade Brackets
- Fix the prepared blade bracket to the motor housing with the blade bracket screws as shown in Fig 2.1.
- Five blade brackets were installed.
Disassemble the Light Set
- Remove the light assembly out of the box and turn the lampshade counterclockwise to disassemble it as shown in Fig 3.1, and then remove the LED light kit out of the light kit pan directly as light kit is fixed by magnetic attraction.
- The light assembly after disassembly is shown in Fig 3.2.
Install the Light Kit Pan & Light Kit
- Remove three screws from the light kit plate of the motor housing.
- Feed the light pin wire and safety rope through centre hole of the light kit pan. Attach the light kit pan to the light kit plate of the motor housing. Reinstall the screws that were removed. Make sure all the screws are firmly tightened.
- Allow the light pin wire and safety rope to come through the light kit. Reinstall the light kit. The light kit is magnetically attracted to the pan with the help of magnets. Insert the light wire connector plug to the light kit terminal block.
Install the Fan Bucket
- Use a screwdriver to loosen and remove the canopy screws and the mounting plate. Save the canopy screws for later use.
- Pull out the control box and adapter out of the fan bucket, locate 6 bucket setscrews in the hardware pack, and secure the fan bucket to the motor housing with the screws. Make sure all screws are firmly tightened.
- Put the control box and adapter together back into the fan bucket as shown in Fig 5.3.
Install the Mounting Plate
You have two options for mounting plate installation. Pick which one works best for your location.
- WARNING: Turn off the power from the breaker circuit first!
- Note: For better fan performance, make sure the mounting plate is level.
- Option 1: Fasten the mounting plate with the ST5x24 wood setscrews (included) when securing to the wooden ceiling beam or support structure with an approved electrical outlet box as shown in Fig 6.1.
- Option 2: Use machine screws (provided with outlet box) and washers when securing an existing ceiling fan-rated outlet box. If the mounting plate is installed at the outlet box, it should be installed on the outlet box with the screws that came with your outlet box itself. Pull the supply wires (the black, white and ground wires) out of the outlet box through the hole in the mounting plate and lay them to the side.
- WARNING: DO NOT use the plastic outlet box. Use only U.L. listed outlet boxes marked ”Acceptable for Fan Support of 15.9 kg (35 lbs) or less”.
Wiring
Hang the Fan
Carefully lift the fan motor assembly. Hang the motor assembly on the hook
of the mounting plate by utilizing one of the holes at the outer rim of the
motor housing so that it is securely suspended.
Connect the Wiring
- Connect the wire plug of the motor to the wire plug of the adapter and confirm the connection is secure.
- The Green/Yellow wire from the mounting plate connects with the supply Ground wire using the wire nut.
- Connect the White wire of the Adapter to the supply White (Neutral) wire using a wire nut, and connect the Black wire of the Adapter to the supply Black/Red (Hot/Live) wire using a wire nut.
- Then hide them and the adapter inside the motor housing. (Make sure all the wires are connected to the correct colours as shown in Fig 8.1)
- Attach the other end of the safety rope to a safe place.
Securing The Fan
- Reinstall two of the four canopy screws (located across from each other) that were removed in step 5 to the mounting plate, but DO NOT tighten them yet.
- Using both hands, lift the fan body from the hook. While making sure the hook is not in the way of the adapter, align the two key slots in the top of the motor assembly with the two loosened screws on the mounting plate.
- Push the fan motor assembly up and turn it counterclockwise to lock in the mounting plate. Tighten the two screws. Reinstall the other two canopy screws into the remaining two holes and tighten the four screws firmly.
WARNING: Falling fan hazard, make sure all screws are tightened to secure the fan motor assembly.
Installation: Lampshade & Power On
Install the Lampshade
Align the lampshade slot with the slot of the light kit pan, and turn it
clockwise to securely lock into the light kit pan as shown in Fig 10.1.
The lampshade is installed as shown in Fig 10.2.
WARNING: To prevent SERIOUS INJURY or DEATH, make sure that the lampshade is properly secured. Allow the lampshade to cool completely before removing.
Power On
At this time, the ceiling fan has been installed. Turn on the power supply
from the breaker circuit of the main switch or the room where the ceiling fan
is installed. After the power is on, observe whether the fan light is on.
Remote Control Instructions
Pair the Remote Control to Your Fan
Power on the fan and pair the remote to the fan within 1 minute. To pair the
remote to the fan, press and hold qJ) button for 3-5 secs to pair the remote
to the fan. Successful pairing will trigger the fan light off.
Remote Control Button Definitions
-
Turns the fan off.
-
Switches between summer mode and winter mode.
- Summer mode – (Counter-clockwise)
-
A downward airflow creates a cooling effect.
- Winter mode – (Clockwise )
-
An upward airflow moves warm air away from the ceiling area and redistributes it around the living space
-
Turns the fan on and decreases fan speed.
-
Turns the fan on and Increases fan speed
-
Nature Switches the fan speed between nature mode and normal mode. Simulates a natural breeze, gentle enough not to disturb you while you sleep.
-
Turns the lights on or off and RF pairing.
-
Note: Power on the fan and pair the remote to the fan within 1 minute. To pair the remote to the fan, press and hold button for 3-5 secs to pair the remote to the fan. Successful pairing will trigger the fan light off.
-
Switches between warm light and cool light. WIFI Troubleshooting.
Note: Press/hold the button for 5 sec. The fan will switch to AP Mode, then select AP Mode on APP, follow the APP control instructions and enable fan Wi-Fi. -
Press/Hold the button to decrease the light intensity.
-
Press/Hold to button to increase the light intensity.
-
WARNING: Do not expose the remote control to direct contact with water
Connecting to the Carro Home App
-
First, download the free Carro Home App from the App Store or Google Play or scan the QR Code below.
Note: This ceiling fan needs to use 2.4Ghz WIFI to work when connecting the device, and after connecting, it can use 5Ghz or 2.4Ghz. -
Open the Carro Home App to create your account. The account with “Carro Home” can be registered through E-mail or Mobile phone.
-
Connect the device to the Carro Home App (Four ways to connect) :
(Bluetooth Connect (WIFI & Bluetooth On}
- a. Press “+” button into the device list, and then a window will pop up to show you some devices that can be connected.
- b. Click “Go to add” (If you click “Do not add” by mistake, please see “Do not add” steps).
- c. Choose the device.
- d. Connect to your home WIFI, then back to the app and wait for connection.
“Do not add” steps:
- a. Select “Electrical” (smart switch) or ”Air Circulation” (smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.
- b. Connect to your home WIFI and tap “Next” to wait for connection.
Auto Scan (WIFI & Bluetooth On}
- a. Press “+” button into the device list.
- b. Tap “Auto Scan” on the top.
- c. Wait for the device to appear and tap “Next”.
- d. Press “+” button to add device.
- e. Connect to your home WIFI.
- f. Wait for the connection.
WIFI Connect-El Mode (WIFI On & Bluetooth Off}
- a. Press “+” button to select “Electrical” (smart switch) or ”Air Circulation” (smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.
- b. Connect to your home WIFI (Only for 2.4 GHz).
- c. EZ Mode is set as default, just tap the “Next” button to wait for the connection to complete.
WIFI Connect-AP Mode (WIFI On & Bluetooth Off}
- a. Smart ceiling fan: Press and hold the WIFI button on the remote for 5 seconds for AP Mode. Smart switch: Press and hold the “OFF” button for 10 seconds till the indicator light blinks slowly to enter into AP Mode.
- b. Press “+” button to select “Electrical” (smart switch) or ”Air Circulation” (smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.
- c. Connect to your home WIFI (Only for 2.4 GHz).
- d. Choose AP Mode.
- e. Press the “Next” button to connect the fan’s WIFI signal.
- f. Choose the fan’s WIFI signal “CarroHome-XXXX” then go back to the app.
- g. Wait for the connection.
Connecting to Smart Devices
- Connect the device to the Alexa:
- a. Make sure you have connected the device to the app and it is working normally.
- b. Open the Alexa app, and go to the skill to search “Carro Home” skill.
- c. Link the skill, log in with your Carro Home App account and password, then authorize and connect with the Carro Home App.
- d. Then Alexa will find the device automatically.
- Connect the device to the Google Home:
- a. Make sure you have connected the device to the app and it is working normally.
- b. Open the Google Home app, Set up a device, and choose ”Works with Google”.
- c. Search “Carro Home”, log in with your Carro Home App account and password, then authorize and connect with the Carro Home App.
- d. Then the Google Assistant will find the device automatically.
- Connect the device to the Siri shortcuts:
- a. Make sure you have connected the device to the app and it is working normally.
- b. Tap “Smart” on the main menu.
- c. Tap “+” button.
- d. Tap “Launch Tap To Run”.
- e. Tap “Run the device”.
- f. Choose the device you want to control by Siri.
- g. Select the function you want to control by Siri.
- h. Then save it.
- I. Add to Siri, choose the scene you just made, Add to Siri.
- j. Enter the sentence you want to say to make the device work, Add to Siri.
Troubleshooting
Try these troubleshooting steps before contacting Customer Service. For additional operation, maintenance, and troubleshooting information, please contact our customer service center.
Care & Cleaning
- Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. Because of the fan’s natural movement, some connections may become loose over time. It is not necessary to remove the fan from the ceiling.
- Clean your fan periodically. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discolouration or tarnishing.
- (Optional) Apply a light coat of furniture polish to the wood blades.
- (Optional) Cover small scratches with a light application of shoe polish.
DO NOT:
- Use water when cleaning. Water could damage the motor, or the wood, or possibly cause an electrical shock.
- Apply oil to your fan or motor. The motor has permanently lubricated sealed ball bearings.
WARNING: Power off the fan before performing maintenance or cleaning the fan.
FCC Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING : Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Important : Please read and save these instructions before installation
Basic Product Specifications
U.S. Patent Nos.: 11,296,561.
Other Patent(s) Pending.
Live Smarter
This Carro Smart Ceiling Fan is:
Questions
Have questions about our products? Contact us and talk to our helpful tech support team.
Technical Support
Business Hours:
Monday – Friday (Holidays observed).
9:00 am to 5:30 pm PST.
Tel: 888-253-2374
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>