Cell2 Photon 8H Riser Block User Manual
- June 9, 2024
- Cell2
Table of Contents
Photon 8H Riser Block
User Manual
TRAFFIC WARNING LIGHT Manual
INTRODUCTION
This lamp is a LED warning light for fixed or temperer/ application in road warning, informing or guiding.
WIRING
OPERATION
For Flash Pattern Selection:
While activating in Warning Mode, momentarily apply +VDC to yellow wire
- once to the next pattern.
- quick three times to pattern #3. (See flash pattern chart)
When FP#3 is selected. lighthead will flash three times upon activation for differentiating purpose.
Warning flash pattern chart
1| Steady
2| Single (1Hz)(Auto-dim Enable]
2| Single (tHz)(Auto-dim Disable]
For Simultaneous or Alternating Synchronization:
-
Disconnect all power, apply +VDC to RED and YELLOW wires simultaneously then remove YELLOW wire from +VDC to enter grouping mode; lighthead will display short (single or double) flashes.
• Single flash = Group1
• Double flash = Group2 -
Remove YELLOW wire from +VDC and momentarily apply to +VDC again to change groups.
• Lightheads in the same group will flash together.
• Grovel lighteads flash altematingly to Group2 lightheads. -
Save and exit grouping mode by disconnecting all power.
MAINTENANCE
- Check and exam for any dirt or smudge on the lens; clean only with water when necc3sary.
- When mounting the product on an automobile. exam the lamp functionality before each driving.
- When using as temporary warning device, check functionality before operating.
DRILLING TEMPLATE
WARNING
WEEE Marking
This product must not be disposed of as standard household waste, but in
accordance with the applicable electronic waste disposal regulations of your
country or region.
INSTALLATION
(the included mounting accessories vary between models) Proper installation of
the product requires the installer to have a good understanding of automotive
electronics, systems and procedures. Different applications may require
different functions. For optimum efficiency, it is highly recommended to
determine, configure and test the required functions prior to Installation.
Surface mount w/ Rubber Riser Block
- Mark and drill 4 mounting holes on a desired mounting surface using the Drilling Template on page 1.
- Orient the mounting Riser Block to a desired wire exit direction.
- Ensure the “ ” marking is oriented upward and secure the lighthead and the Riser Block on to the mounting surface with the provided screw pack. (Set torque force @ 12-14Kgf-cm (10-12 lbf-in))
NOTE: Mounting surface thickness @ 1-5mm (0.04-0.2in)
Surface mount w/o Rubber Riser Block
- Mark and drill 4 mounting holes and a wiring hole on a desired mounting surface using the Drilling Template on page 1.
- Feed the wire through the wiring hole.
- Ensure the “ ” marking is oriented upward and secure the lighthead on to the mounting surface with the provided screw pack. (Set torque force @ 12-14Kgf-cm [10-12 Ilkin))
NOTE: Mounting surface thickness @ 1-5mm (0.04-0.2in)
U-bolt clamp mount w/ Rubber Riser Block
- Orient the Rubber Riser Block to a desired wire exit direction.
- Ensure the “ ” marking is oriented upward and secure the U-bolt assembly and the Riser Block on to the lighthead using the provided screw pack. (Set screw torque force @ 12-14Kgf-cm [10-12 lbf-in])
- Secure the lighthead assembly on to the pole with the pole retainer plate and the provided nuts. Make use of the swivelable plate for smooth installation when needed. (Set nut torque force @ 120-130Kgf-cm [104-113 lbf-in])
NOTE: Applicable pole diameter @ fb 25.4 – 50.8mm (1-2in).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>