INNOKIN KLYPSE MECHA Refillable Pod Kit User Guide
- June 16, 2024
- INNOKIN
Table of Contents
KLYPSE MECHA Refillable Pod Kit
User Guide
Components
Smart Mode
The device auto-adjusts to the supported power range of your pod for
optimal performance.
Interface
HOW
TO FILL
- Fill the pod. Pull tab to open and add E-liquid.
- Insert pod into the device and simply puff to start your vaping experience.
WARNING:
Wait at least 5 minutes fter filling a new pod with e-liquid so the cotton can
( be saturated with e-liquid before use.
IMPORTANT
- Ensure the battery contacts and pod are clear of debris and e-liquid residue.
- For the best longevity and flavour, keep the pod at least 1/3 full.
- Do not vape if the pod is empty.
- Replace the pod if you experience a burnt taste.
- If you notice a severe reduction in flavour or vapour and recharging the device does not improve performance, replace the pod.
OPERATIONS
ON/OFF: SRD, 3x Clicks within 2 Seconds. To Lock/Unlock the Screen:
Press and hold the button for 3 seconds to lock or unlock the screen. When
locked, you can vape but cannot make adjustments.
Menu Settings:
- Press the button twice to access menu. Setting: Time: Set or Deactivate the time mode Screen: Screen timeout (5-180 seconds) Query: Clear puff count
- Rotate the dial for selection and hold the button to confirm and access the settings.
- Press and hold the button for 1 second to exit settings and return to the main interface.
Voltage/Wattage Adjustment
- Press and hold for 1 second until the numbers start flashing to access adjustment mode.
- Rotate the button to increase or decrease the voltage/wattage.
- Each left turn reduces the value by 0.1V/0.SW, and each right turn increases it by 0.1V/0.5W.
CHARGING & SAFETY
Battery Level Indicator:
Charge promptly based on the battery level ring.
While charging, a lighting bolt icon displays on the screen and the battery
ring will fill.
When fully charged, the screen displays 100%.
Cautions:
- Charge with a certified SV wall charger and USB-C cable.
- DO NOT leave the device unattended when charging. *DO NOT store the device with a depleted battery.
- Keep the device away from direct sunlight and excessive heat.
SPECIFICATIONS
Dimensions: 94.2 x 42.7 x 17 mm
Pod: 2ml I 0.60
Voltage: 1.0-4.SV
Wattage: 6-18W
Puff Activated Auto-Draw
Cut-off Time: 3-10s
Built-in Battery Capacity: 900mAh
Charging Specifications: DCSV I 0.8A
PROTECTIONS
LOW VOLT
Warning is displayed when the battery voltage is too low.
Solution: Charge the device. CHECK COIL
Warning is displayed when the load exceeds 3.5 ohms or when there is no load.
Solution: Check the connection of the pod or replace the pod. COIL LOW
Warning s displayed when the load is short-circuited or below 0.5 ohms.
Solution: Check the pod or replace the pod. COIL SHORT
Warning is displayed when there is a short circuit.
Solution: Check the pod or replace the pod. 
TIMEOUT
Warning is displayed when you exceed 10 seconds of vaping.
Solution: Wait for 2 seconds before vaping again. HIGH TEMP
Warning is displayed when the PCB temperature is too high.
Solution: Wait for the device to cool down before vaping again.
If you have ony questions, contact
support@innokin.com
facebook.com/lnnokin.Technology
instagram.com/innokintechnology
twitter.com/innokintech
reddit.com/r/innokin
support@nnokin.com
Manufacturer: Shenzhen lnnokn Technology Co , Ltd.
Address: ‘lst-Sth F oor, Building 6, Xnxint an Industrial
Park, Xinsha Road, Shaer Community, Shajing, Baoan
District, 518104. Shenzhen. China.
Telephone: +86 755 2989 8770
Email: info@innokn.com
Production License: 5144030162
ISO 9001 / 14001 / 45001, ISO 13485, and cGMP Certified.
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>