FANGIO ATI-HSV1500 Infrared Zone Heating System Owner’s Manual
- June 6, 2024
- FANGIO
Table of Contents
INFRARED ZONE HEATING SYSTEM
Model No. ATI-HSV1500
OWNER’S MANUAL
PLEASE SAVE THESE INSTRUCTIONS WARNING: READ THIS OWNER’S MANUAL CAREFULLY
BEFORE USE.
Thank you for purchasing this ATI heater. This owner’s manual will provide you
with valuable information necessary for the proper care and maintenance of
your new product. Please take a few moments to thoroughly read the
instructions and familiarize yourself with all the operational aspects of your
new heater.
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons. including the following:
- Read ALL instructions before using this unit.
- CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
- This heater may get hot when in use. To avoid bums, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater.
- Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
- Extreme caution is necessary when any heater is used by or near children or the disabled, or when the heater is left operating and unattended.
- DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate a heater where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids.
- DO NOT touch the control panel or plug with a wet hand.
- DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, DO NOT block the air intake or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive, and/or flammable liquids are used or stored. Keep unit away from heated surfaces and open flames.
- Always plug heaters directly into a wall outlet! receptacle Never use with an extension cord or relocatable power tap(outlet power strip)
- To avoid fire or shock hazards, plug the unit directly into a 120 V AC electrical outlet.
- To disconnect the heater. turn controls to OFF, then remove the plug from the outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord.
- Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
- Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may cause hazards.
- Always use on a dry, level surface. Use on floor only.
- DO NOT use outdoors.
- WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.
- DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user-serviceable parts. Qualified personnel should perform all servicing only.
- Connect to properly grounded outlets only.
- Save these instructions.
SPECIFICATIONS
| Voltage Rating | 120 V (60Hz) |
|---|---|
| Power Consumption | 1500W |
| Unit Size | 13.3 in. (W) x 12.3 in. (D) x 7.5 in. (H) |
| Unit Weight | lbs |
SAFETY FEATURES
Tip-Over Safety Feature
This heater is equipped with a tip-over safety feature. Once the heater is
tipped over, an internal switch will automatically shut the heater off. Once
the heater is restored an upright position, the heater will reset. To continue
operation, turn on the heater using the supplied remote control or the control
panel on the heater.
Overheat Safety Feature
This heater is equipped with an overheat safety feature. When the heater’s
internal components reach a certain temperature that could cause overheating
or possible fire, the heater will automatically shut off.
WARNING: This heater has a voltage rating of 120 volts. The cord has a
plug as shown in A. An adapter as shown in C is available for connecting
three-blade grounding-type plugs to two-slot receptacles. The grounding lug
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used if a three-slot
grounded receptacle is available. DO NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDED PLUG.
WARNING: It is normal for the power cord to feel warm to touch: however, a loose fit between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified electrician to inspect the original outlet for damage.
IN THE BOX
- INFRARED HEATER
- REMOTE CONTROL
- INSTRUCTION BOOKLET
PRODUCT DIAGRAM
- Timer button: for setting timer function.
- Mode button: for the select running mode.
- Power switch button: for power ON or OFF.
- Power indication Light: indicate when the unit connects to the power supply.
- The heat-up indicator indicates when the heat-up mode is on.
- Digital display: indicate set room temperature and set timer value.
- Celsius indicator light.
- Signal-receiving window: for receiving a remote control signal.
- Temp up button: for setting the temperature higher.
- Temp down button: for setting the temperature lower.
- PDF Button: Button to alternate between Fahrenheit and Celsius readout
- Timer indication light: indicates when the timer is functioning.
- Fahrenheit indicator light.
- Energy-saving indicator: indicate when the energy-saving mode is on.
- The heat-down indicator indicates when the heat-down mode is on.
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet. and turn on the power switch in the rear of the unit Only operate the heater in an upright position with caster wheels attached.
OPERATING INSTRUCTIONS
1. Start
| Turn on or off the heater by pressing the ON/OFF button on the control panel
or by pressing the Power button on the supplied remote control.
Once power is off, heating elements will stop working first. The fan will
continue working for up to 3 minutes to dispense residual heat inside the
heater. This is a normal function.
---|---
2. Start and select working mode
| Select a heat setting.
Press the MODE button to toggle between the three heat settings.
---|---
| High Mode uses 1500W; Low Mode uses 1000W. ECO mode is an Economic Energy
Saving Function. When ECO mode is chosen, the heater will manage itself from
less to more heating power (watts) In an attempt to maintain a constant warm
68’F(20 C).
- Setting control panel lock
For safety, users can lock the control panel so children can’t operate the heater. Locking can be set in both power-on and power-off modes.
| Press Temp Up and Temp Down buttons together for 3 seconds. Locking is
confirmed when a buzzer rings. When locked, the control panel and remote
control will not function.
---|---
| To unlock, press Temp Up and Temp Down buttons together for 3 seconds.
Unlocking is confirmed when a buzzer rings. Lock indication disappears. The
Control panel and remote control return to normal function.
4. Setting room temperature
| Adjust the thermostat by pressing the arrows on the control panel or remote
control.
---|---
| Set temperature indication varies from 59°F to 86Tor from 1St to 30°C. Once
you have chosen the desired temperature, the heater will remain on until the
room temperature increases to the temperature on the digital display. The
heater will cycle on and off to maintain the desired room temperature.
| Press C/Fº button to change the digital display indicator to Fahrenheit
value or Celsius value.
| When Fahrenheit indicates light is on, the digital display indicates
Fahrenheit value, when Celsius indicates the light is on. a digital display
indicates Celsius value.
- Setting timer-power-off
Note: timer-power-off function can only be set while the heater is in power-on mode.
| When starting the unit, press the timer button on the control panel or
remote control.
---|---
| The digital display turns set temperature readout to time value for the
timer. Press the timer button repeatedly, the value will vary from 0 hours to
12-hour duration (inl hour intervals).
| The light is on when timer —power-off is set.
---|---
- Setting timer-power-on
Note: timer-power-on function can only be set while the heater is in power-off mode.
| Under power-off. Press the timer button on the control panel.
---|---
| Digital will indicate the time value for the timer. Press the timer button
repeatedly, the value will vary from 0 hour to 12 how duration (in I hour
intervals).
| The light is on when the timer —power-on is set.
MAINTENANCE
- Turn off the power switch in the rear of the unit.
- Unplug the unit and let it cool completely.
- To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soli cloth. CAUTION: DO NOT let liquid enter the heater.
- DO NOT use alcohol, gasoline. abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
- DO NOT immerse the heater in water.
- Wait until the unit is completely dry before use.
- Air filter should be cleaned after use for 3 months or if it appears to be blocking airflow. With the heater unplugged, remove 2 filter screws as illustrated below. With filter assembly removed, Clean all parts of the filter assembly. Allow parts to completely dry.
- Reassemble filter and then attach to the heater. WARNING: Do not use a heater without filter assembly in place.
- If you won’t use the heater for a long time, take the battery out of the remote control according to the below steps and store for future use.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit.
TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair of service:
- Check if the power cord is plugged into an electrical outlet, if not, plug in.
- Check if the electricity to the main fuse is working.
- Check if the battery in the remote control is not dead and if the insulating film is pulled out.
NOTE: For the heater to function properly, the desired temperature on the heater must be set a few degrees higher than the temperature in the room. If the seems to not be heating, increase the desired temperature on the heater to engage the heat elements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>