INNOKIN ZYON Pod Electronic Cigarette User Manual
- June 1, 2024
- INNOKIN
Table of Contents
INNOKIN ZYON Pod Electronic Cigarette
COMPONENTS
FILLING THE POD
Pull the tab to open and add E-liquid.
IMPORTANT
- Wait for at least five minutes after filling to allow the new coil to saturate with E-liquid.
- You can also manually prime your coil by placing three drops of E-liquid into the coil.
- Keep the pod from going completely empty of E-liquid. Refill it regularly to avoid dry hits or coil damage.
CHANGING THE COIL
When you experience a burnt taste or a decrease in flavour and/or vapour production, it’s time to change the coil.
- Pull and remove the old coil.
- Prime and install a new coil in its place.
ADJUSTING THE AIRFLOW
Turn the pod to customize the airflow to achieve your desired draw.
POWER ON/OFF THE DEVICE
Click the power button three times continuously to turn the device on or off.
INTERFACE
ADJUSTING THE WATTAGE
Click the power button twice continuously. When the power value on the screen starts to blink, click the power button to select the required watt value.
After the watt value is selected, wait for two seconds to exit the power setting.
CHARGING
- Charge promptly based on battery level.
- Use the provided charging cable and a standard output charger with the correct charging current and voltage range.
CAUTIONS
- Turn the device off when not in use to avoid depleting the battery and minimize excess battery wear.
- Do not leave the charging device unattended.
- Protect the device from direct sunlight, dust, moisture, or mechanical shock.
- Avoid dropping, throwing, or mishandling the device to prevent damage.
- Keep the device away from any water, liquid, or flammable gas.
SPECIFICATIONS
Dimensions: 4Φ29 x 100,2 mm
Capacity: 4.5 ml
Coils & Recommended Wattage: PZP Coil 0.60 (18-24W): PZP Coil 1.20
(10-13W)
Output Power: 6.Ω-25.0W Built-in Battery Capacity: 1300mAh
Charging Current: DC 5.0V / 0.75A
Button-activated: Hold the power button to start vaping
PROTECTION
No Load/ High Resistance Protection
When no load resistance or high resistance is detected, the screen will display”- – – -” and flash.
Short Circuit Protection
When low resistance is detected, the screen will display”- – – -” and stay on for 5 seconds.
Auto-Shut Off Protection
If the power button is held for 10 seconds, the screen will display ” – – – -” and flash 10 times.
Overheat Protection
When the PCBA (Printed Circuit Board Assembly) temperature sensor detects high temperature, the screen will display ” – – – -” and flash 3 times, then 3 times again.
CUSTOMER SUPPORT
Manufacturer: Shenzhen lnnokin Technology Co., Ltd.
Address: 1st-5th Floor, Building 6, Xinxintian Industrial Park, Xinsha
Road, Shaer Community, Shajing, Baoan District, 518104, Shenzhen, China.
Telephone: +86 755 2989 8770
Email: info@innokin.com
Production License: 5144030162 ISO 9001 /14001 / 45001, ISO 13485, and
cGMP Certified.
MADE IN CHINA
European Representative:
FRANCE VAPOTAGE DISTRIBUTION 57 impasse de la Ferme Cardon Rue de la Croix
Bougard 59810 LESQUIN France
Telephone: +33 320020152
Email: guillaume.vilain@innokin.fr
KEEP OUT OF REACH OF CHILDREN.
Documents / Resources
|
INNOKIN ZYON Pod Electronic
Cigarette
[pdf] User Manual
ZYON Pod Electronic Cigarette, ZYON, Pod Electronic Cigarette, Electronic
Cigarette, Cigarette
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>