VIVO STAND-TV70B Space Saving 49 to 70 inch LED LCD Studio TV Display Stand User Manual

VIVO STAND-TV70B Space Saving 49 to 70-inch LED LCD Studio TV Display

Stand

Black V-Base Studio TV Stand

Specifications:

• SKU: STAND-TV70B
• Weight Capacity: 88lbs (40kg)

Product Usage Instructions

Tools Needed:

• Phillips Screwdriver
• Tape Measure
• Drill
• Pencil
• Stud Finder

Assembly Steps

Step 1:

Slide the Feet (C) onto the base of the Leg (A). Insert M8x12mm Screws (S-A) into the bottom holes of the feet. Tighten with the 5mm Allen Wrench (T-B). Insert M6x15mm Screws (S-B) through the base into the rear holes of the feet. Tighten with the 5mm Allen Wrench (T-B).

Note: Screw the Foot Pads (F) into the base, and adjust foot pads to sit level on the floor.

Step 2:

Screw Pole (B) onto Leg (A). Loosen the set screws in Collar (B1) using the 4mm Allen Wrench (T-A). Adjust height of Collar (B1) to the recommended position below the top of the pole based on your TV’s VESA mounting hole pattern. Tighten the set screws, making sure they face towards the back of the stand.

Note: Ensure the collar is securely locked before mounting the TV.

Step 3:

Remove Screw (E1) from the lower VESA Bracket (E) and open the clamp.

Step 4:

• Option A: Flat Back TV Position
  Upper VESA Bracket (D) over top holes on TV and secure with Screws (M-A or M-B), M8 Washers (M-E) and Security Clips (P-B). Position the Lower VESA Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8 Washers (M-E).

• Option B: Curved Back TV Position
  Upper VESA Bracket (D) over top holes on TV and secure with Screws (M-A or M-B), M8 Washers (M-E), and Security Clips (P-B). Position the Lower VESA Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8 Washers (M-E). If needed, Spacers(M-F, M-G) have been provided.

Step 5:

Slide the TV onto the assembled stand. Close the clamp on the Lower VESA Bracket (E) over the pole and secure it with the previously removed Screw (E1).

Step 6:

Route cables through the cable holes in the Leg (A). Install Cable Covers (G) to the cable holes, using pliers to break out sections for x2 or x3 cables if needed.

Anchor TV Stand

• Option A: Wood Wall Installation
  Using Security Cable Clamps (P-C) as guides, mark drilling locations on the wall. Use of a stud finder is recommended. Drill holes at least 1.6″ (40mm) deep using a 1/8″ (3.5mm) drill bit.

FAQ

Q: What is the weight capacity of the TV stand?

A: The weight capacity of the TV stand is 88lbs (40kg).

Q: Are all the hardware included necessary for assembly?

A: No, some hardware may not be used depending on your specific TV and installation requirements.

Black V-Base Studio TV Stand

WARNING

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIP OVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• * NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.

  • USE TIP-OVER RESTRAINT OR ANCHOR STAND TO WALL
    THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

TOOLS NEEDED

ASSEMBLY STEPS

STEP 1

• Slide the Feet (C) onto the base of the Leg (A). Insert M8x12mm Screws (S-A) into the bottom holes of the feet. Tighten with the 5mm Allen Wrench (T-B). Insert M6x15mm Screws (S-B) through the base into the rear holes of the feet. Tighten with the 5mm Allen Wrench (T-B).

• Screw the Foot Pads (F) into the base, and adjust foot pads to sit level on the floor.

STEP 2

• Screw Pole (B) onto Leg (A). Loosen the set screws in Collar (B1) using the 4mm Allen Wrench (T-A). Adjust height of Collar (B1) to the recommended position below the top of the pole based on your TV’s VESA mounting hole pattern. Tighten the set screws, making sure they face towards the back of the stand.

STEP 3

• Remove Screw (E1) from the lower VESA Bracket (E) and open the clamp.

STEP 4

• OPTION A: Flat Back TV
  Position Upper VESA Bracket (D) over top holes on TV and secure with Screws (M-A or M-B), M8 Washers (M-E) and Security Clips (P-B). Position Lower VESA Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8 Washers (M-E).

• OPTION B: Curved Back TV
  Position Upper VESA Bracket (D) over top holes on TV and secure with Screws (M-A or M-B), M8 Washers (M-E) and Security Clips (P-B). Position Lower VESA Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8 Washers (M-E). If needed, Spacers (M-F, M-G) have been provided.

STEP 5

• Slide the TV onto the assembled stand. Close the clamp on the Lower VESA Bracket (E) over the pole and secure with previously removed Screw (E1).

STEP 6

• Route cables through the cable holes in the Leg (A). Install Cable Covers (G) to the cable holes, using pliers to break out sections for x2 or x3 cables if needed.

Anchor TV Stand

• OPTION A: Wood Wall Installation
  • Using Security Cable Clamps (P-C) as guides, mark drilling locations on the wall. Use of a stud finder is recommended. Drill holes at least 1.6” (40mm) deep using a 1/8” (3.5mm) drill bit.

• * Mount Clamps (P-C) to the wall using ST4.8 x38mm Screws (P-E).

• • Thread Steel Cable (P-A) through the Security Clips (P-B) on the TV and center holes in the Cable Clamps as shown, then tighten clamps using the 2mm Allen Wrench (P-D).

• OPTION B: Concrete/Brick Wall Installation
  • Using Security Cable Clamps (P-C) as guides, mark drilling locations on the wall. Drill holes at least 1.6” (40mm) deep using a 9/32” (7mm) drill bit.

• * Insert Anchors (P-F) into the holes and mount Clamps (P-C) to the wall using ST4.8 x38mm Screws (P-E).

• • Thread steel cable (P-A) through the Security Clips (P-B) on the TV and center holes in the cable clamps as shown, then tighten the clamps using the 2mm Allen wrench (P-D).

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

SKU: STAND-TV70B

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-tv70b

AVG. RESPONSE TIME (within office hrs): 1HR 8M

– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr

LAST UPDATED: 11/20/2023 REV5.1

GET IN TOUCH | Open Monday – Friday 7:00 am – 7:00 pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

help@vivo-us.com

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
• Black V-Base Studio TV Stand for 49" to 70" TVs – VIVO - desk solutions, screen mounting, and more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>