VIVO STAND-V012J Dual Monitor Desk Mount with Laptop Holder Instruction Manual

: June 16, 2024
: Vivo

Table of Contents

VIVO STAND-V012J Dual Monitor Desk Mount with Laptop Holder
PACKAGE CONTENTS
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIVO STAND-V012J Dual Monitor Desk Mount with Laptop Holder

Specifications:

SKU: STAND-V012J
Weight Capacity: 22 lbs (10kg) per arm

Package Contents:

A (x1) Bottom Pole
B (x1) Top Pole
C (x1) Clamp
D (x1) Dual Arm
E (x1) Single Arm
F (x1) Tray
G (x3) VESA Plate
H (x1) Grommet Plate
I (x1) Soft Pad
J (x1) Pole Cable Clip
K (x6) Arm Cable Clip
L (x1) Pole Cap
S-A (x3) M6x16mm Screw
S-B (x3) M6 Security Nut
S-C (x4) M4x8mm Screw
S-D (x4) M4 Nut
M-A (x8) M4x12mm Thumbscrew
M-B (x8) M4x30mm Screw
M-C (x8) M6 Spacer
T-A (x1) 3mm Allen Wrench
T-B (x1) 5mm Allen Wrench
T-C (x1) Wrench

Tools Needed:

Phillips Screwdriver

Assembly Steps:

Step 1:
Loosen the knob on Clamp (C).
Step 2 (Option A):
Clamp Installation
- Mount Clamp (C) to Bottom Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
- Secure the assembly to the desktop by tightening the knob on Clamp (C).
Step 2 (Option B):
Grommet Installation
- Using a Phillips screwdriver, remove the screw from Clamp (C) and disassemble it. Set Hand Bolt (C1) and Clamp Plate (C2) aside.
- Place the Clamp Plate (C2) over the Hand Bolt (C1).
- Mount Grommet Plate (H) to Bottom Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
- Remove adhesive backing from Soft Pad (I) and adhere it to Grommet Plate (H).
- Place the pole assembly over the grommet hole in the desk and connect using the previously removed Hand Bolt (C1) and Clamp Plate (C2) from underneath the desk.
- Secure by tightening the Hand Bolt (C1).
- For desktops without an existing grommet hole, use a 3/8 (10mm) drill bit to drill through the desktop, then secure the assembly as previously described.
Step 3:
Slide Pole Cable Clip (J) and Single Arm (E) onto Bottom Pole (A). Secure Single Arm (E) in place using 5mm Allen Wrench (T-B).
Step 4:
Thread Top Pole (B) onto the Bottom Pole (A). Slide Dual Arm (D) onto Top Pole (B). Secure Dual Arm (D) in place using 5mm Allen Wrench (T-B). Attach Pole Cap (L) to Top Pole (B).
Step 5:
Attach Arm Cable Clips (K) to Dual Arm (D) and Single Arm (E).
Step 6:
Assemble Laptop Tray (F) to VESA Plate (G) using M4x8mm Screws (S-C) and M4 Nuts (S-D). Tighten the assembly using Wrench (T-C) and a Phillips screwdriver.
Step 7:
Slide Tray (F) with VESA Plate (G) onto Single Arm (E). Secure VESA Plate (G) in place using M6 Security Nut (S-B).
Step 8:
Secure VESA Plates (G) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm Screws (M-B). M6 Spacers (M-C) may be required.
Slide monitors with VESA Plates (G) onto Dual Arm (D). Secure VESA Plates (G) in place using M6 Security Nuts (S-B).
STEP 9
Manage cable using Pole Cable Clip (J) and Arm Cable Clip (K).
STEP 10
Adjust the monitor tilt using a 5mm Allen Wrench (T-B). To level monitors, remove M6 Security Nuts (S-B) and tighten or loosen adjustment screws using a 3mm Allen Wrench (T-A). Once level, fasten M6 Security Nuts (S-B) back into place.

FAQ:

Q: What is the weight capacity of this desk mount?
A: The weight capacity is 22 lbs (10kg) per arm.
Q: What tools are needed for assembly?
A: You will need a Phillips screwdriver.
Q: Can I use this desk mount with a desktop without an existing grommet hole?
A: Yes, you can use a 3/8 (10mm) drill bit to drill through the desktop and secure the assembly as described in the instructions.

SKU : STAND-V012J

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. Instruction Manual
https://vivo-us.com/products/stand-v012j

GET IN TOUCH | Monday-Friday from 7:00 am-7:00 pm CST

help@vivo-us.com
www.vivo-us.com
309-278-5303
Chat live with an agent!

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE : SOME HARDWARE INCLUDED MAY NOT BE USED

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED

PACKAGE CONTENTS

TOOLS NEEDED

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

ASSEMBLY STEPS

Step 1:
Loosen the knob on Clamp (C).
Step 2 (Option A):
Clamp Installation
- Mount Clamp (C) to Bottom Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
- Secure the assembly to the desktop by tightening the knob on Clamp (C).
Step 2 (Option B):
Grommet Installation
- Using a Phillips screwdriver, remove the screw from Clamp (C) and disassemble it. Set Hand Bolt (C1) and Clamp Plate (C2) aside.
- Place the Clamp Plate (C2) over the Hand Bolt (C1).
- Mount Grommet Plate (H) to Bottom Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).
- Remove adhesive backing from Soft Pad (I) and adhere it to Grommet Plate (H).
- Place the pole assembly over the grommet hole in the desk and connect using the previously removed Hand Bolt (C1) and Clamp Plate (C2) from underneath the desk.
- Secure by tightening the Hand Bolt (C1).
- For desktops without an existing grommet hole, use a 3/8 (10mm) drill bit to drill through the desktop, then secure the assembly as previously described.
Step 3:
Slide Pole Cable Clip (J) and Single Arm (E) onto Bottom Pole (A). Secure Single Arm (E) in place using 5mm Allen Wrench (T-B).
Step 4:
Thread Top Pole (B) onto the Bottom Pole (A). Slide Dual Arm (D) onto Top Pole (B). Secure Dual Arm (D) in place using 5mm Allen Wrench (T-B). Attach Pole Cap (L) to Top Pole (B).
Step 5:
Attach Arm Cable Clips (K) to Dual Arm (D) and Single Arm (E).
Step 6:
Assemble Laptop Tray (F) to VESA Plate (G) using M4x8mm Screws (S-C) and M4 Nuts (S-D). Tighten the assembly using Wrench (T-C) and a Phillips screwdriver.
Step 7:
Slide Tray (F) with VESA Plate (G) onto Single Arm (E). Secure VESA Plate (G) in place using M6 Security Nut (S-B).
Step 8:
Secure VESA Plates (G) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm Screws (M-B). M6 Spacers (M-C) may be required.
Slide monitors with VESA Plates (G) onto Dual Arm (D). Secure VESA Plates (G) in place using M6 Security Nuts (S-B).
STEP 9
Manage cable using Pole Cable Clip (J) and Arm Cable Clip (K).
STEP 10
Adjust the monitor tilt using 5mm Allen Wrench (T-B). To level monitors, remove M6 Security Nuts (S-B) and tighten or loosen adjustment screws using 3mm Allen Wrench (T-A). Once level, fasten M6 Security Nuts (S-B) back into place.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 07/12/2023

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product

278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
Chat live with an agent!
help@vivo-us.com

AVG. RESPONSE TIME (within office hrs): 1HR 8M