VOLTCRAFT VC-12 1000A Capacitor Jump Starter Instruction Manual

VOLTCRAFT VC-12 1000A Capacitor Jump Starter

Product Information

Specifications

• Input voltage/current: 12V/10A
• Output voltage: 12V
• Inrush current: 500A
• Peak current: 1000A
• Capacitor: Charging time – approx. 3 minutes (70 Ah battery), Lifespan – approximately 10,000 cycles
• Reverse polarity protection: Yes
• Short circuit protection: Yes
• Dimensions (W x H x D): 136 x 57 x 200 mm
• Weight (approx.): 1.00 kg

Product Usage Instructions

Intended Use
The VC-12/1000A Capacitor Jump Starter is designed to be used as a standalone vehicle battery jump starter. It utilizes a capacitor to capture and store residual energy from a weakened 12V battery and then releases that stored energy to crank start the engine. It is important to note that this product cannot be used on a battery with a voltage of less than 6V. Please only use the product for its intended purpose as described in the user manual to avoid any damage or hazards.

Safety Precautions
Before using the VC-12/1000A Capacitor Jump Starter, please ensure you read and understand the following safety precautions:

• Electrical Safety: Always turn off the vehicle engine and electronics before connecting or disconnecting the product. Failure to do so may result in entanglement, burns, or other injuries. Avoid loose clothing and keep away from the starter battery.
• Proper Voltage: Test the battery voltage before providing jump-start assistance. The battery voltage should be less than 13.8V for safe operation.
• Low Voltage Protection: Ensure that the battery to be jump-started has a voltage greater than 6V. If the battery voltage is lower, do not proceed with jump-starting.
• High Voltage Protection: Do not attempt to jump-start a battery with a voltage higher than 13.8V. Test the battery voltage before providing jump-start assistance.

Product Components
The VC-12/1000A Capacitor Jump Starter includes the following components:

• LCD-Bildschirm (LCD Screen)
• Einschalttaste (Power Button)
• Kabelklemmen (Cable Clamps)

LCD Status Indicator
The VC-12/1000A Capacitor Jump Starter features an LCD status indicator that provides important information about the battery and charging status. The indicator includes the following:

• Batteriespannung (Battery Voltage): Displays the current voltage of the battery being jump-started.
• A die Batterie angeschlossen (Connected to Battery): Indicates whether the jump starter is properly connected to the battery.
• Ladezustand des Kondensators (Capacitor Charging Status): This shows the charging status of the capacitor. It displays “LOW” when the capacitor needs charging and “READY” when it is fully charged.

Operation
To use the VC-12/1000A Capacitor Jump Starter, follow these steps:

1. Make sure the vehicle engine and electronics are turned off.
2. Connect the cable clamps to the corresponding battery terminals (red clamp to positive terminal, black clamp to negative terminal).
3. Press the Einschalttaste (Power Button) to activate the jump starter.
4. The LCD screen should turn on and display the battery voltage. If it does not, refer to the troubleshooting section.
5. If the LCD screen shows “READY,” proceed to start the vehicle engine. If it shows “LOW,” the capacitor needs charging. Repeat steps 2-3 after charging the capacitor.

Troubleshooting
If you encounter any issues with the VC-12/1000A Capacitor Jump Starter, refer to the following troubleshooting codes:

• Code F01: The voltage of the battery to be jump-started is too high. Test the battery voltage, it should be less than 13.8V.
• Code F02: The LCD display is not activating. Test the battery voltage, it should be greater than 6V.
• Code F03: The battery to be jump-started has a voltage of less than 2 Ah. Try jump-starting with a different battery or consult a qualified technician.
• Code F04: The battery to be jump-started has a voltage of less than 5.5V. Try jump-starting with a different battery or consult a qualified technician.

Cleaning and Maintenance
To clean and maintain the VC-12/1000A Capacitor Jump Starter, follow these steps:

1. Disconnect the product from the power source.
2. Use a dry, lint-free cloth to clean the product.

Disposal
Dispose of the VC-12/1000A Capacitor Jump Starter according to local regulations for electronic waste disposal. Do not dispose of it in regular household waste.

FAQ (Frequently Asked Questions)

• Q: Can I use the VC-12/1000A Capacitor Jump Starter on a battery with a voltage lower than 6V?
  A: No, this product is designed to be used on batteries with a voltage greater than 6V.

• Q: Does the VC-12/1000A Capacitor Jump Starter need to be charged?
  A: No, this product does not contain a rechargeable battery and therefore does not need to be charged.

• Q: What should I do if the LCD display does not activate?
  A: Test the battery voltage using a voltmeter. If the battery voltage is higher than 6V, consult a qualified technician for further assistance.

• Q: How long does it take to charge the capacitor?
  A: The capacitor typically takes approximately 3 minutes to charge when used with a 70-Ah battery.

VC-12/1000A Capacitor Jump Starter

• Item no: 2799626

Intended use

• The product is a standalone vehicle battery jump starter. It uses a capacitor to capture and store residual energy from a weakened 12V battery, then releases that stored energy to crank start the engine. It cannot be used on a battery that has a voltage less than 6V.
• This product does not contain a rechargeable battery so does not need to be charged.
• If you use the product for purposes other than those described, the product may be damaged.
• Improper use can result in short circuits, fires, electric shocks or other hazards.
• The product complies with the statutory national and European requirements.
• For safety and approval purposes, you must not rebuild and/or modify the product.
• Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions.
• All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery contents

• Product
• Operating instructions

Operating Instructions for download

Use the link www.conrad.com/downloads (alternatively scan the QR code) to download the complete operating instructions (or new/current versions if available). Follow the instructions on the web page.

Description of symbols

The following symbols are on the product/appliance or are used in the text:

• The symbol warns of hazards that can lead to personal injury.
• This product must only be used in dry, enclosed indoor areas. It must not become damp or wet.
• Read the operating instructions carefully.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

General

• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• If you have questions that remain unanswered by this information product, contact our technical support service or other technical personnel.
• Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

Handling

• Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

Operating environment

• Do not place the product under any mechanical stress.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
• Protect the product from high humidity and moisture.
• Protect the product from direct sunlight.

Operation

• Consult an expert when in doubt about the operation, safety or connection of the product.
• If it is no longer possible to operate the product safely, take it out of operation and pro-tect it from any accidental use. DO NOT attempt to repair the product yourself. Safe op-eration can no longer be guaranteed if the product:
  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to serious transport-related stresses.

Electrical safety

• Switch off the vehicle engine and electronics before connecting the product.
• Clean the battery terminals to maintain proper contact and prevent short circuits.
• Avoid electric shock! Do not operate the product with wet hands and check the battery clamp and cable insulation is not damaged.
• Remove metal jewellery (e.g., necklaces, rings) when working with batteries to reduce the risk of short circuits, electric shocks, or burns.

Personal safety

• Wear eye protection to prevent injuries from explosions or corrosive chemicals while working with lead-acid batteries.
• Risk of explosion! Never operate the product in areas where flammable fumes or gases are present (e.g. petrol stations).
• Risk of burns – Allow engine compartments to cool down as they can reach high temperatures.
• Keep away from moving engine parts like belts, pulleys and fans.
• Risk of entanglement and burns! Loose clothing and jewellery can get caught or entangled in moving or hot parts.
• Explosive/noxious gases may be produced/present during use. Always use the product in a well-ventilated area.
• Have someone nearby in case there is an emergency.

Lead-acid battery

• Keep fresh water, soap and eyewash within reach.
  • If battery acid contacts skin or clothes, wash immediately with soap and water.
  • Avoid touching eyes. If acid enters the eyes, flush with water for 10 minutes and seek medical help immediately.

Electric vehicles

• Electric vehicles may have specific requirements for jump-starting procedures.
• Always consult the vehicle operating instructions for information about the starter battery.

Product Overview

Product

1. LCD screen
2. Power button
3. Leads

LCD status display

1. Battery voltage
2. Connected to battery
3. Battery voltage out of range:
   • LOW: <6 V
   • HIGH: >13 V
4. Ready for jump-starting
5. Capacitor charging status

Connection

Preparation for connection
Before connecting the cables to a battery:

• Switch OFF all vehicle electrics (e.g. air conditioner, heater, radio, lights etc.).
• Make sure the ignition key is in the “OFF” position. For push-to-start ignition, make sure the vehicle is completely OFF.
• Check the battery contact terminals are clean.
• Prepare your vehicle for ignition (e.g. place the gear in park and engage the emergency brake).

Connecting the leads

Important:
Always connect test leads to terminals in the correct order.

1. Connect the red clamp to the positive (+) terminal.
2. Connect the black clamp to the negative (-) terminal.
3. Wiggle the clamps back and forth to ensure proper connection.
4. The LCD should activate. If the LCD does not activate see section: Troubleshooting

Disconnecting the leads

When finished using the product:

1. Press the button to switch the power OFF.
2. Disconnect the red clamp.
3. Disconnect the black clamp.

Operation

1. Connect the product to the vehicle battery terminals. See section: Connection.
2. Press the button to switch the power ON.
   • If everything is functioning correctly the capacitor will start charging. See section: LCD status display.
   • If there is a problem with the battery an error message will appear. See section: Troubleshooting.
3. Wait for a “beep” sound and READY to appear on the display.
   • Jumpstart the vehicle engine.
4. If ignition is successful, let the engine run to allow the battery to recharge, and disconnect the product from the battery. See section: Disconnecting the leads.
   • If ignition is not successful, switch the product OFF, and repeat steps 2 – 3.

Notes:

• In some cases when the ambient temperature is <0 °C, the LCD may not activate but the product will still function.
• In such cases wait approximately 5 minutes for the audible “beep”. This indicates the capacitor has reached full charge and is ready to jump-start the vehicle engine.

Troubleshooting

battery, it should be <13.8 V.
F02| The rechargeable battery voltage is too low.| Test the rechargeable battery, it should be >6 V.
F03| The product has a circuit malfunction.| Do not use the product.
F04| Rechargeable battery capacity is <2 Ah.| Try to recharge the battery or consult a qualified technician.
LCD does not activate| The cables are not connected correctly.| Recheck the connections.
The rechargeable battery voltage is <5.5 V.| Try to recharge the battery or consult a qualified technician.
The weather is too cold (<0 °C).| The LCD does not activate but the capacitor may still function. See section: Operation.

Cleaning and care

Important:

• Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They damage the housing and can cause the product to malfunction.
• Do not immerse the product in water.

1. Disconnect the product from the power supply.
2. Clean the product with a dry, fibre-free cloth.

Disposal

• This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life.
• Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):

• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

Technical data

• Input ……………………………………….. 12 V 10 A
• Output……………………………………… 12 V
• Starting current…………………………. 500 A
• Peak current …………………………….. 1000 A
• Capacitor ………………………………….
  • Charging: approx. 3 mins. (70 Ah battery)
  • Lifespan: approx. 10,000 cycles
• Reverse polarity protection…………. yes
• Short circuit protection……………….. yes
• Operating conditions………………….. -40 to +65 °C, 20 to 80 % RH (non-condensing)
• Storage conditions…………………….. -40 to +65 °C, 20 to 80 % RH (non-condensing)
• Dimensions (W x H x D) …………….. 136 x 57 x 200 mm
• Weight (approx.)……………………….. 1.00 kg

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited. This publication reflects the technical status at the time of printing.

Copyright by Conrad Electronic SE.

2799626_V1_1123_dh_mh_en 18014399382736523-2 I3/O1 en

References

• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>