VOLTCRAFT UC-3ACX001 USB Charger Mains Socket User Manual
- June 3, 2024
- VOLTCRAFT
Table of Contents
VOLTCRAFT UC-3ACX001 USB Charger Mains Socket
Intended use
The product has two USB-A outputs and one USB-C® (PD 3.0) output. The product is suitable for charging and operating up to three USB devices at the same time. Power is supplied via a standard household mains socket. The product is protected against short circuit and overload. This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g. in a bathroom) must be avoided under all circumstances. For safety and approval purposes, do not rebuild and/or modify this product. Using the product for purposes other than those described above may damage the product. In addition, improper use can cause hazards such as short circuit, fire or electric shock. Read the operating instructions carefully and store them in a safe place. Only make this product available to third parties together with its operating instructions. This product complies with statutory, national and European regulations. All company and pro-duct names contained herein are trademarks of their respective owners. All rights reserved.
Delivery content
- Charger
- USB-C® to USB-C® cable (approx. 1 m)
- Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Description of symbols
The symbol with the lightning in the triangle is used if there is a
risk to your health, e.g. due to an electric shock.
The symbol with an exclamation mark in a triangle is used to highlight
important information in these operating instructions. Always read this
information carefully.
This symbol indicates that the power adapter has a protection class
II. It is equipped with reinforced or dual insulation between the mains
circuit and the output voltage.
The product must only be installed and used in dry, indoor
locations. It must not become damp or wet, as this may cause a fatal electric
shock!
This symbol indicates that the product meets the requirements for Level VI
Energy Efficiency.
Safety information
Read the operating instructions carefully and observe in particular
the safety instructions. If you do not follow the safety information and
information on
proper handling in these operating instructions, we will assume no liability
for any resulting personal injury or damage to property. Such cases will
invalidate the warranty/guarantee.
General information
- This product is not a toy. Keep it out of the reach of children and pets.
- Do not leave packaging material lying around carelessly. It may become a dangerous plaything for children.
- Protect the product from extreme temperatures, direct sunlight, strong jolts, flammable ga-ses, vapours and solvents.
- Never expose the product to any excessive mechanical stress.
- If it is no longer possible to operate the product safely, stop using it and prevent unautho-rised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
- Handle the product carefully. Jolts, impacts or a fall even from a low height may damage the product.
- The mains socket that the device is plugged into must be easily accessible.
- Unplug the connected USB device from the product when you are not using it.
- Electrical devices must never be plugged in or unplugged with wet hands.
- If the product shows signs of damage, do not touch it, there is a risk of death from an elec-tric shock! First, switch off the mains voltage to the mains socket to which the product is connected (switch off the respective circuit breaker or remove the safety fuse; then switch off the respective GFCI so that the mains socket is fully disconnected). You can then unplug the mains plug from the mains socket. Dispose of the damaged product in an environmen-tally friendly manner, stop using it. Replace it with an identical product.
- Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of injury.
- The product must only be powered by a standard mains socket connected to the public grid. Before plugging in the product, check that the voltage indicated on the product corre-sponds to the voltage of your electricity supplier.
- For safety reasons, disconnect the product from the mains socket during storms.
- Ensure no liquids can spill on electrical appliances and never place any objects filled with liquids near the device. Should liquid penetrate the device nonetheless, cut off the power supply to the relevant mains socket (e.g. via the circuit breaker) and pull the mains plug out of the mains socket. Discontinue use and take the product to a specialist repair centre.
- Never use the product immediately after it has been taken from a cold room into to a warm one. This may cause condensation to form, which can destroy the product. Furthermore, it can cause a lethal electric shock! Allow the product to reach room temperature before connecting it and putting it into use. This may take several hours.
- Make sure the USB ports are not short-circuited.
- Ensure there is sufficient air circulation when you operate the product. Never cover the product.
- Consult a technician if you are not sure how to use or connect the product, or if you have concerns about safety.
- If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.
Connected devices
- Always observe the safety information and operating instructions of any other devices which are connected to the product.
- Always switch off the USB device to be connected before connecting and disconnecting.
Operation
- Connect the power plug to an appropriate power outlet.
- Before connecting your USB device to one of the USB-A outputs or the USB-C® output, make sure it is switched off. You can charge up to three devices at the same time. In the table below, you will find the available charging currents/charging powers.
- Note: the USB-A (QC 3.0) operation is only possible if at least one of the two USB-A outputs is free.
- The USB device will start to charge. Should you wish to operate the USB device, you may turn it on now.
- Switch off the USB device before you unplug it from the product.
- The outputs can be used to charge devices with different voltages (5 V, 9 V, 12 V) and USB Power Delivery (PD 20 W).
- Disconnect all connected USB devices from the USB charger after use. Disconnect the USB charger from the car power socket after use.
Care and cleaning
- Disconnect the product from the power supply.
- Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may damage the
- Do not immerse the product in water. Wipe the product with a dry cloth regularly.
Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed
of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and
accumulators, which are not enclosed by the WEEE, as well as lamps that can be
removed from the WEEE in a non-destructive manner, must be removed by end
users from the WEEE in a non-destructive manner before it is handed over to a
collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.
Technical data
Data according to EU regulation 2019/1782
| Manufacturer | Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau |
|---|---|
| Commercial registration number | HRB 3896 |
| Model identifier | UC-3ACX001 |
| Input voltage | 100 – 240 V/AC |
| Input AC frequency | 50 – 60 Hz |
| Output voltage | USB-C ® : |
| Output current | 5.0 V/DC, 3.0 A, max. 15.0 W |
| Output power | 9.0 V/DC, 2.22 A, max. 20.0 W |
| 12.0 V/DC, 1.67 A, max. 20.0 W | |
| USB-A1: | |
| 5.0 V/DC, 3.0 A, max. 15.0 W | |
| 9.0 V/DC, 2.0 A, max. 18.0 W | |
| 12.0 V/DC, 1.5 A, max. 18.0 W | |
| USB-A2: | |
| 5.0 V/DC, 3.0 A, max. 15.0 W | |
| 9.0 V/DC, 2.0 A, max. 18.0 W | |
| 12.0 V/DC, 1.5 A, max. 18.0 W | |
| USB-A1 + USB-A2: | |
| Output power 15.0 W max. (share) | |
| Total output 38.0 W max. | |
| Average active efficiency | 85.9 % |
| Efficiency at low load (10 %) | 76.3 % |
| No-load power consumption | 0.23 W |
Other
Weight ………………………………………………….approx. 96 g (without cable)
Dimensions ……………………………………………102 x 56 x 28 mm
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is
prohibited. This publication represent the technical status at the time of
printing. Copyright 2022 by Conrad Electronic SE.