BLAUPUNKT BPS-E694 4 Way Car Speaker System User Manual
- June 16, 2024
- Blaupunkt
Table of Contents
4 Way Car Speaker System
E-Series
BPS-E694
X-Series
BPS-X6940
BPS-E694 4 Way Car Speaker System
BP Americas Corp.
9590 NW 40th St Road Doral, FL 33178
| Model: | BPS-E694 | BPS-X6940 |
|---|---|---|
| Speaker Design | 6*9″ 4Way | 6X9″ 4way |
| Woofer [in, mm] | 69in 164236mm | 69in 164236mm |
| Mid [in, mm] | 2in 50mm | 2in 50mm |
| Tweeter [in, mm] | 1.2in 30mm | 1.2in 30mm |
| Supertweeters [in,mm] | 0.5in 12mm | 0.5in 12mm |
| Rated Impedance | 4ohm | 4ohm |
| Peak Power Handling [Watts] | 70W | 70W |
| Continous Power Handling [Watts] | 35W | 35W |
| Sensitivity [1W, 1m] | 85.3dB | 88.7dB |
| Frequency Response [Hz] | 45~20000Hz | 40~20000Hz |
| Mounting Hole Diameter [in, mm] | 6.068.74in 154222mm | 6.068.74in 154222mm |
| Top Mount Depth [in, mm] | 1.42in 36mm | 1.5in 38mm |
| Bottom Mount Depth [in, mm] | 3.15in 80mm | 3.15in 80mm |
| Tweeter Protrusion [in, mm] | 0 | 0 |
| Grilles | Yes | Yes |
| Tweeter Magnet Material | Neodymium | Neodymium |
| Tweeter Dome Material | PET | PEI |
| Tweeter Design | balanced dome | balanced dome |
| Supertweeter Magnet Material | —— | —— |
| Supertweeter Dome Material | Ceramic w/ PET Diaphragm | Ceramic w/PEI Diaphragm |
| Supertweeter Design | Balanced Dome | Balanced Dome |
| Midrange Magnet Material | Ferrite | Ferrite |
| Midrange Dome Material | PET | PEI |
| Midrange Design | Balanced Dome | Balanced Dome |
| Woofer Cone Material | PP | Carbon fiber |
| Woofer Surround Material | Rubber | Rubber |
WIRING
Blaupunkt Speaker wired to a single channel
Total Impedance: 4 ohms x channel
Blaupunkt Speakers wired in
parallel to a single channel
Total Impedance: 2 ohms x channel
MOUNTING
NOTE: BLAUPUNKT strongly recommends that you operate your system at low
volume levels prior to the complete installation of your BLAUPUNKT speakers.
CAUTION: Make sure that all of the speaker wiring is fully protected from
cuts, tears or possible wear. Any short circuit caused from cuts, tears or
wears, could severely damage the source unit or amplier. Make sure all speaker
wires easily reach the speaker terminals with no stress on the wires or
connectors.
IMPORTANT: Never cut any metal that is an integral part of the vehicle’s
safety or structural support system. If you are unsure of the importance of
any components of your vehicle, it is recommended that you have your speaker
professionally installed.
CHOOSING A LOCATION: It is always best to plan the complete installation
prior to attempting to install any product. The routing of wires, power
connections, and mounting location, should be planned rst. As with any car
stereo installation, all work performance should be checked throughly and
carefully prior to the operation of the system.
BLAUPUNKT Speakers are designed to t in almost any factory location. If at all
possible, it is recommended that you use factory locations. This applies
mostly to later model cars.
For those earlier model cars, that do not have factory location or are limited
to just front speakers, it is recommended that you choose a location with a
sufficient amount of air space.
If there’s not enough air space, the woofer of the speaker may not reproduce
low frequencies very well. It is recommended to mount the speakers in the door
panels, kick panels, rear deck, etc.
Ideally, the speakers should be mounted where it will be in an enclosed
airspace.
This allows for an extended bass response.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>