VALBERG WD 10614 A-D W180C Washing Machine Instruction Manual

VALBERG WD 10614 A-D W180C Washing Machine

Product Information

Specifications

• Model: 980314 – WD 10614 A/D W180C
• Washing/drying Capacity: 10 / 6kg
• Max. spin speed: 1400rpm
• Net Weight: 70kg
• Rated Voltage: 220 – 240V~
• Heating Power: 1500W
• Washing Power: 250W
• Drying Power: 1350W
• Spinning Power: 500W
• Dimension:
  • A: 595mm
  • B: 845mm
  • C: 540mm
  • D: 590mm
  • E: 635mm
  • F: 1120mm

Product Usage

Installation
Before installing the washing machine, it is important to remove the transportation bolts as they are potentially dangerous. Follow the steps below:

1. Screw off all transportation bolts for approximately 30mm using a wrench, following the direction of the arrow shown (do not fully screw them off).
2. Push the four transportation bolts inward in the horizontal direction and loosen the transportation bolt.
3. Pull out the transportation bolt together with the rubber part and plastic part.

To ensure safety and reduce noise, install the transportation bolt cover supplied with the unit. Lean and place the transportation bolt into the hole and press it following the shown direction until it clicks. Keep the transport bolts and the wrench for future transporting of the appliance.

Adjustment of the Feet
The appliance must be installed on a solid and level floor surface. If necessary, use a spirit level. If installing on a wooden floor, distribute the weight by placing it on a 60x60cm sheet of plywood at least 3cm in thickness and secure it to the floor. If the floor is uneven, adjust the 4 levelling feet as required; do not insert pieces of wood or other objects under the feet. Follow the steps below:

1. Slacken the locknut clockwise using the wrench.
2. Lift the machine slightly and adjust the height of the foot by revolving it.

Important : Tighten the locknut by turning it anti-clockwise towards the appliance casing.

Install Bottom Cover
To realize quieter operation, a bottom cover is supplied with the unit (only applies to some models). After installing the cover at the bottom of the washer, the noise level will be greatly reduced. Please ask for advice from specialists before installing the cover. Nevertheless, the machine can be used without the bottom cover.

FAQ

• Q: Can I use the washing machine without installing the bottom cover?
• A: Yes, you can use the washing machine without installing the bottom cover. However, if you want a quieter operation, it is recommended to install the bottom cover.
• Q: Can I adjust the levelling feet on an uneven floor?
• A: Yes, you can adjust the levelling feet on an uneven floor to ensure the washing machine is stable. Do not insert pieces of wood or other objects under the feet.
• Q: How should I transport the washing machine?
• A: When transporting the washing machine, make sure to use the provided transportation bolts and wrench. Follow the installation instructions in reverse order to secure the appliance for transportation.

Thank you!
Thank you for choosing this VALBERG product. VALBERG products are chosen, tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a top-quality, easy-to-use product that won’t let you down. We’re confident your new device will be a pleasure to use every day!

Welcome to ELECTRO DEPOT

Product Overview

Parts

• Worktop
• Control panel
• Detergent dispenser
• Door
• Plinth covering pump access
• Adjustable feet

NOTE:
The control panel layout and appearance will depend on the model.

Parts supplied

• Package with small items
• Instruction for use, installation guide, warranty card (depends on model)
• 4 plastic caps
• Wrench
• Inlet hose (inside the machine or already installed)
  • Cold inlet hose
  • Hot inlet hose (if available, depending on models)
• “U”-bend (inside the machine or already installed)
• Bottom cover (depends on model)

Specifications

Dimension

Installation

BEFORE USING THE WASHING MACHINE

Removing the packaging and inspection

• After unpacking, ensure that the washing machine is undamaged. If in doubt, do not use the washing machine. Contact After-Sales Service or your local retailer.
• Check that the accessories and supplied parts are all present.
• Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of children, as they are potentially dangerous.

Remove the transport bolts

Important:
Transport bolts that are not removed can cause damage to the appliance.

1. Screw off all transportation bolts for approx. 30mm with wrench following the direction of the arrow shown (not fully screw it off).
2. Push four transportation bolts in a horizontal direction inward and loose transportation bolts.
3. Pull out the transportation bolt together with the rubber part and plastic part.
4. To ensure safety and reduce noise, you should install the transportation bolt cover supplied with the unit (see the annex accompanying the unit). Lean and place the transportation bolt into the hole and press it following the shown direction until it clicks.

Important : Keep the transport bolts and the wrench for future transporting of the appliance and in this case refit the transport bolts in reverse order.

Adjustment of the feet
The appliance must be installed on a solid and level floor surface (if necessary use a spirit level). If the appliance is to be installed on a wooden floor, distribute the weight by placing it on a 60x60cm sheet of plywood at least 3cm in thickness and secure it to the floor. If the floor is uneven, adjust the 4 levelling feet as required; do not insert pieces of wood etc. under the feet.

1. Slacken the locknut clockwise (see arrow) using the wrench.
2. Lift the machine slightly and adjust the height of the foot by revolving it.

Important: Tighten the locknut by turning it anti-clockwise towards the appliance casing.

Install bottom cover
To realize quieter operation, a bottom cover is supplied with the unit (only applies to some of the Hisense washers). After installing the cover at the bottom of the washer, the noise level will be greatly reduced. Please ask for advice from specialists before installing the cover, nevertheless, the machine can be used without the bottom cover.

Noise-reduction bottom plate installation instructions

1. Before installing the noise-reduction bottom plate, align and paste the acoustic absorption wool with and along the right-angle impression on the bottom plate (this procedure is unnecessary for some of the models without acoustic absorption wool).
2. Remove surface paper on double-sided tape on four sides of the bottom plate.
3. Incline the machine to an angle of 40° and let the side with a right-angle notch face towards the front of the washing machine, as shown in the figure. Insert the side with an oblique-angle notch between two-foot screws at the back of the washing machine completely in place. Then, install the bottom plate and ensure that it contacts with bottom of the washing machine closely.
4. Press the double-sided tape on four sides manually to secure the noise-reduction plate to the machine body firmly.

Connect the water supply inlet hose

1. If the water inlet hose is not already installed, it must be screwed to the appliance. The blue-marked hose is only for cold water.
2. Screw by hand the inlet hose onto the tap, by tightening the nut.

Attention:

• No kinks in the hose!
• The appliance must not be connected to the mixing tap of an un-pressurized water heater.
• Check the water-tightness of the connections by turning the tap completely on.
• If the hose is too short, replace it with a suitable length of pressure-resistant hose (1000 kPa min).
• Check the inlet hose regularly for brittleness and cracks and replace if necessary.
• The washing machine can be connected without a non-return valve.

Connect the drain hose
In case the drain hose is installed as shown below:

1. Unhook it only from the right clip (see arrow)
2. Connect the drain hose to the Drain or hook it over the edge of a sink using the “U” bend. Fit the “U” bend E, if not already installed, at the end of the drain hose.

Notes:

• Ensure that there are no kinks in the drain hose.
• Secure the hose so that it cannot fall. After the wash phase, the machine will drain out hot water.
• Small hand basins are not suitable.
• To make an extension use a hose of the same type and secure the connections with clips.
• Max. Overall drain hose length: 2.50 m.

Before the first wash cycle
To remove any residual water used during testing by the manufacturer, we recommend that you carry out a short wash cycle without laundry.

1. Open the tap.
2. Close the door.
3. Pour a little detergent (about 30 ml) into the main wash chamber of the detergent dispenser.
4. Select and start a short programme.

Preparation of the washing

Sort the laundry according to…

1. Type of fabric/care label symbol
   Cotton, mixed fibres, easy care/synthetics, wool, handwash items.
   Colour
   Separate coloured and white items. Wash new coloured articles separately.
   Loading
   Wash items of different sizes in the same load to improve washing efficiency and distribution in the drum.
   Delicates
   Wash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras) in a cloth bag or pillow case with a zip. Always remove curtain rings or wash curtains with the rings inside a cotton bag.

2. Empty all pockets
   Coins, safety pins etc. can damage your laundry as well as the appliance drum and tub.

3. Fasteners
   Close zips and fasten buttons or hooks; loose belts or ribbons should be tied together. Stain removal Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the program.

• To remove red wine, coffee, tea, grass and fruit stains etc. add a stain remover to the main wash chamber of the detergent dispenser.
• Pre-treat heavily soiled areas with stain remover if necessary.

Dyeing

• Only use dyes that are suitable for washing machines.
• Follow the Manufacturer’s instructions.
• Plastic and rubber parts of the washing machine can be stained by dyes.

Loading the laundry

1. Open the door.

2. Load the articles one at a time loosely into the drum, without overfilling. Observe the load sizes given in the quick reference guide.
   Note : Overloading the machine will result in unsatisfactory washing results and creased laundry.

3. Close the door.

Detergents and additives

Always use high-efficiency, low-foam detergent for a front-load machine. The choice of detergent depends on:

• type of fabric (cotton, easy care/synthetics, delicate items, wool).
  Note : Use only specific detergents for washing wool.

• colour

• the wash temperature

• degree and type of soiling

Remarks:
Any whitish residues on dark fabrics are caused by insoluble compounds used in modern phosphate-free powder detergents. If this occurs, shake or brush out the fabric or use liquid detergents. Use only detergents and additives specifically produced for domestic washing machines. When using descaling agents, dyes or bleaches for the pre-wash, make sure that they are suitable for use in domestic washing machines. Descalers could contain products that could damage your washing machine. Do not use any solvents (e.g. turpentine, benzine). Do not wash fabrics that have been treated with solvents or flammable liquids.

Dosage
Follow the dosage recommendations on the detergent pack. They depend on:

• degree and type of soiling
• size of wash follow the detergent manufacturer’s instructions for a full load; half load: 3/4 the amount used for a full load; minimum load (about 1 kg): 1/2 the amount used for a full load;
• water hardness in your area (ask for information from your water company). Soft water requires less detergent than hard water.

Notes:
Too much detergent can result in excess foam formation, which reduces washing efficiency. If the washing machine detects too much foam, it may prevent spinning. Insufficient detergent may result in grey laundry in time and also calcify the heating system, drum and hoses.

Where to put detergent and additives
The detergent drawer has three chambers (fig. “A”)

Prewash chamber

• Detergent for the prewash/soak

Mainwash chamber

• Detergent for the main wash
• Stain remover
• Water softener (water hardness class 4)

Softener chamber

• Fabric softener

Notes:

• Keep detergents and additives in a safe, dry place out of the reach of children.
• Liquid detergents can be used for programs with prewash. However, in this case, a powder detergent must be used for the main wash.
• Do not use liquid detergents when activating the “Start Delay” function (if available on your washing machine).
• To prevent dispensing problems when using highly concentrated powder and liquid detergents, use the special detergent ball or bag supplied with the detergent and place it directly inside the drum.
• When using descaling agents, bleaches or dyes, make sure that they are suitable for washing machines. Descalers could contain compounds that can damage parts of your washing machine.
• Do not use any solvents in the washing machine (e.g. turpentine, benzine).

Operation

This washing machine is equipped with automatic safety functions that detect and diagnose at an early stage and react appropriately.

Control Panel

1. Program selector
2. “Temp.” button
3. “Spin” button
4. “Option” button
5. “Dry level” button
6. “Delay End” button
7. “Start/Pause” button
8. Program and function status display window

Programmes

• ∗ : Optional Functions
• Yes : Detergent Required
• — : Cannot be selected
• — : Temperature of unheated water
• D : Default

Please select the appropriate washing temperature according to the instructions on the care labels attached to the clothes, if not, the clothes can be damaged.

Add detergent, close the door and set the program
Load the clothes to be washed in the drum and close the door. Add the detergent into the relevant compartments for the type of program you are going to select, Add detergent as described in the Detergent and Additives section.

1. Turn on the power.
2. Spin the program selection knob to the required program, “off” must be passed through if the pointer’s initial position is not “off”.
3. Select washing temperature, and spin speed by pressing the “Temp”, and “Spin” buttons.
4. Press the “Option” button to select additional functions.
5. After starting the program, the display window displays the program length (hours: minutes) and additional function options in sequence.

Programme| Washing temperature select| Laundry and textile| Recommended detergent
---|---|---|---
Wool| –, 20, 30, 40°C| Wool fabric| Mild detergent

20°C

|

20°C

| Synthetic materials, coloured laundry made from easy-care fibres| Colour or mild detergent without optical brighteners

Quick 15’ Mix

|

–, 20, 30, 40°C

| Synthetic materials, coloured laundry made from cotton or linen| Colour detergent free of bleach and optical brighteners

Synthetics

|

–, 20, 30, 40, 60°C

| Synthetic materials, coloured laundry made from cotton or linen| Colour detergent free of bleach and optical brighteners

Cotton

|

–, 20, 30, 40, 60, 90°C

| Synthetic materials, coloured laundry made from cotton or linen| Colour detergent free of bleach and optical brighteners

Allergy Care

|

40, 60, 90°C

| White laundry made from boil-proof cotton or linen| Strong detergent containing bleach and optical brighteners

Addition function selection
At standby state, press the “Option” button to select an additional function for the current program. Select only one function for each press, and then the corresponding icon flashes. After starting up, the program cannot be changed.

Pre-wash

• Select the function to conduct pre-wash to enhance washing effects and better remove stains. This function is suitable for heavy-dirt clothes.
• Before inflowing, laundry detergent/washing powder can be added to the pre-wash box, and washing powder must be added to the main wash box.

Extra rinse

• After setting the function of rinsing adding, the program runs the rinsing process once again before running the softening, and the total running time of the program increases accordingly.

Inlet water warning
If the tap is not opened, or the water pressure is over low, the display screen will prompt “F01” to give the alarm.

Drainage warning
If the pipe is squeezed, drainage will not be smooth. In case of failing to completely drain for a long time, the display screen will prompt “F03” to give the alarm.

Door lock icon
After the program starts the Door Lock icon will light up and the door will be locked.

• After completing the program, the door lock unlocks automatically. When the washing machine is paused, if the door lock opening conditions are met, the door lock will open.
• When the door lock indicator light flashes, the door shall not be opened forcibly to avoid personal injury.

Delay end function
The Delay End function allows them to run the machine at the consumers’ convenience, for example, at night when electricity is cheaper.

• Only under the standby mode, this button is valid for selecting the reservation time.
• After the reservation function is selected, the time will increase by 1h when each time the reservation button is pressed. Before reservation, if the program time does not satisfy the integral multiple of 1h, it shall be completed by pressing the reservation key for the first time, and then the time increases by 1h when each time the reservation button is pressed. If the reservation is selected, before the program runs, the current reservation can be cancelled by turning the button to select other programs.
• The delay time must be longer than the wash program length as the delay time is the time the program will finish. For example: if the selected program time is 02:28, the delay time selected must be between 03:00 and 24:00.
• When the reservation process is operated, the icon of “reservation time” will be on. When the reservation process is finished, the icon of “reservation time” will be off.
• If the delay end is selected and the start button is not pressed, the delay can be cancelled by rotating the rotary knob before starting.
• To cancel the delay time during the delay program, you need to turn the machine off by pressing the “On/Off” button for 2 seconds.

Mute function
When the machine is in the state of holding, pause or operation, press the “Spin+ Option” buttons for 2 seconds, The display will show “bEEp oFF”. All the buzzing will be turned off except the alarms. When the machine is in the mute state, press the “Spin+ Option” buttons for 2 seconds until “bEEp on” appears. All the buzzing will be activated.

Child lock
To strengthen the safety of children, this machine is equipped with a Child Lock function. When the programme starts, press the “Temp. +Spin” button for 2 seconds. Then Child Lock is set up. Repeat the same operation, the Child Lock will be released.

• When the Child Lock is set, all function buttons will be shielded.
• When you turn the machine off by rotating the program selection button“Off”, the child lock is released.
• After completing the program, the child lock will automatically unlock.

To start the program
After you have selected your options and placed detergent with the detergent dispenser, turn on the water tap and press the “Start/Pause” button. The screen will display the current program progression with icons from left to right. It also displays the remaining program time.

To cancel the program or reselect the options

1. Rotate the program to “Off” for 3 seconds to turn off the machine.
2. Select the new program and options.
3. Press the “Start/Pause” button to turn on the machine without adding any extra detergent.

End of the program
When the program finishes running, it will display “End”. If no operation is taken in 2 minutes, the machine will turn off automatically.

1. Rotate the program to “Off” to turn off the machine;
2. Close the tap;
3. Open the door and take the washed clothes out;
4. Slightly open the door to remove moisture in the pump.

Reload in Process
If you want to reload clothes in the process of washing, please press the “Start/Pause” button.

• If the reload icon lights up, the door can be opened in the process, remaining time and the Door Lock icon in the display will flash. Then the Door Lock icon will go out, and the door can be opened.
• If the reload icon doesn’t light up, the Door Lock icon doesn’t flash, it indicates that the current temperature is over 50°C or you have passed the time for reloading in the process, namely no clothes are allowed to load into the machine.

Automatic weighting
The washing machine displays “—-” after startup, indicating that it is weighing automatically. It will adjust the program length (hours: minutes) automatically according to the weight of the clothes.

Dry
Press the “Dry Level” button to select the dry time and additional functions of dry. When the Iron , Cupboard and Extra Dry functions are selected, the corresponding icon will light up, and the remaining time of the program will be displayed on the display window. When the [Time Dry] function is selected, the icon of Time Dry will light up.

The washing machine can sense the weight of clothes to adjust the dry time automatically.

• Before drying, please confirm whether the clothes can be dried (please refer to the program table to confirm the type of clothes that can be dried).
• Before starting to dry, make sure that the tap is open and the cold water is in place.
• Before separately drying, please take the after-spinning clothes out from the drum, and put them into the drum after making it loose.
• When little clothes or light clothes are dried, the dry time may be shorter than the setting time.
• If the hand-washing clothes require drying, before drying, please select the spin with as high speed as possible according to the clothes types. It is recommended to select the “Spin + Dry Level” program.
• At the end of drying, the washing machine will run for some time according to a certain rhythm to loosen the clothes and reduce the wrinkle.
• If the clothes adhere to the inner wall of the cylinder, it will affect the drying effect. So it is recommended to dry the clothes after loosening them manually.
• Excessive drying may affect the dry effect, it may cause wrinkles in clothes. For the chemical fibre clothes, such as shirts, etc., the iron mode shall be selected.
• If the clothes with different materials are dried together, the dry effect may be affected. So it is recommended to classify the clothes before drying.
• If the dry failure occurs, please refer to the contents of [Dry Fault] for processing.

[Iron] function owns the effect that the clothes with little water can be ironed after being dried.[Cupboard] function owns the effect that the clothes can be worn instantly after being dried.[Extra Dry] function owns the effect that the clothes can be stored up after being dried.[Time Dry] function refers to drying the clothes for a specified time.

Users press the “Dry Level” button to select any type of dry time with 6 types, including 30 minutes, 1 hour, 1.5 hours, 2 hours, 3 hours, and 4 hours. Please select a reasonable dry time. Otherwise, the clothes will not be dried fully if the drying time is too short.

Notes : The wet clothes still dripping are not suitable for drying, which may cause the machine to alarm!

Rough weight of washes

Fabric care chart

Non-washable dry/non-dry clothes Clothes that can neither be washed nor dried

Non-dry clothes

If it is used to dry cushions and clothes with furs, it may lead to drain pipe blockage.

Notes:

• Non-washable dry/non-dry clothes include but are not limited to the above clothes.
• The wet clothes still dripping are not suitable for drying, which may cause the machine to alarm!

Dry fault

The washing machine does not carry out the drying process

| •  Check whether the dry program is set up.

•  Check whether the water tap is unopened.

•  Check whether the door is well closed.

•  Check whether the dry clothes are excessive (refer to the program table and check the corresponding capacity of the program), and take out part of the clothes to dry again.

Dry is not sufficient

| •  Check whether the dry clothes are excessive. If so, it will cause unsatisfactory dry effects and folds in clothes. Please divide the clothes in the drum into two parts for drying separately.

•  Check whether the clothes (such as thicker cotton, etc.) that are not easy to dry are mixed with the clothes that are easy to dry (such as chemical fibre, etc.). Please dry the clothes of different types separately or dry them again.

Dry time is too long

| •  Check whether the drying clothes are excessive (refer to the program table and check the corresponding capacity of the program), and take out part of the clothes to dry again.

•  Clothes are not fully dewatered (refer to the treatment of bad dehydrated effect in the manual).

•  More thicker clothes (denim, etc.).

Programme Instructions

1. The eco 40-60 program can clean normally soiled cotton laundry declared to be washable about 40°C to 60°C, together in the same cycle, and this program is used to assess compliance with the EU ecodesign legislation.
2. The power consumption of the off-mode is 0.49W, and the left-on mode is 0.49W.
3. The most efficient programmes in terms of energy consumption are generally those that perform at lower temperatures and longer duration.
4. Loading the household washing machine or the household washer-dryer up to the capacity indicated by the manufacturer for the respective programmes will contribute to energy and water savings.
5. Correct use of detergent, softeners and other additives. Do not apply excessive detergent. This may affect the washing results adversely.
6. Periodic cleaning, including optimal frequency, and limescale prevention and procedure.
7. Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning speed in the spinning phase, the higher the noise and the lower the remaining moisture content.
8. The product information and the energy consumption label, the product registration information can be obtained by scanning the QR code.
9. The information of standard programmes.
10. The wash and dry cycle can clean normally soiled cotton laundry declared to be washable at 40°C or 60°C, together in the same cycle, and dry it in such a way that it can be immediately stored in a cupboard, and that this programme is used to assess the compliance with the EU ecodesign legislation.

Program

|

Selected Temperature

|

Rated Capacity (kg)

|

Maximum temperature in the drum

|

Program duration (h: min)

|

Energy consumption (kWh/cycle)

| Water consumption (litres/ cycle)|

Remaining moisture content (%)

| Maximum speed reached rpm
---|---|---|---|---|---|---|---|---
Eco 40-60 full load| –| 10| 35| 3:48| 0.98| 65| 52.50| 1400
Eco 40-60 half load| –| 5| 29| 3:00| 0.48| 50| 52.50| 1400
Eco 40-60 1/4 load| –| 2.5| 25| 3:00| 0.22| 30| 52.50| 1400
Wash and Dry full load| –| 6| 26| 10:30| 3.60| 102| 1.10| 1400
Wash and Dry half a load| –| 3| 26| 6:30| 2.30| 70| 0.40| 1400
Cotton| 20°C| 10| 20| 2:09| 0.20| 85| 51.00| 1400
Cotton| 60°C| 10| 55| 3:29| 1.60| 85| 51.00| 1400
MIX| 40°C| 5| 38| 1:58| 0.75| 69| 45.00| 1400
Quick 15′| 40°C| 1| 38| 0:30| 0.33| 22| 55.00| 800
20’C| 20°C| 10| 20| 1:50| 0.20| 85| 51.00| 1400

The values given for programmes other than the eco 40-60 programme and the wash and dry cycle are indicative only.

Emergency door opening
In case of failure to open the door due to a power outage or other special circumstances, the door lock lever at the drainage pump door can be used for emergency opening.

Notes:

• Do not operate when the machine is working normally;
• Before the operation, please make sure that the inner barrel has stopped turning, without high temperature, and the water level is lower than the clothing inlet. If the water level is higher than the clothing inlet, drain off water through the drain-away pipe (if available) or by slowly unscrewing the filter.
• Operation method: Open the cover of the drainage pump door, pull down the lock lever with the help of a tool, and then the door can be opened(indicated in the figure).

Cleaning and maintenance

Care and maintenance

Appliance exterior and control panel

• Can be washed down with a soft, damp cloth.
• A little neutral detergent (non-abrasive) can also be used.
• Dry with a soft cloth.

Door seal

• Clean with a damp cloth when necessary.
• Check the condition of the door seal periodically.

Detergent dispenser

1. Press the release lever in the main wash compartment downward and remove the drawer. (fig.“B”)
2. Remove the iPhone in the softener slot. (fig.“C”).
3. Wash all the parts under running water.
4. Refit the siphon in the detergent drawer and fit the drawer back inside its housing.

Filter
We recommend that you check and clean the filter regularly, at least two or three times a year.

Especially:

• If the appliance is not draining properly or if it fails to perform spin cycles.
• If the pump is blocked by a foreign body (e.g. buttons, coins or safety pins).

IMPORTANT : Ensure that the water has cooled before draining the appliance.

1. Stop the appliance and unplug it.
2. Insert a removal tool like a slotted screwdriver into the small opening of the bottom baffle, press the bottom baffle downward with much strength and open it.
3. Put a flat container under the filter door and then drain with an emergency drain pipe (see [draining residual water] for specific operation methods). Then, loosen the filter anticlockwise and completely unscrew and remove the filter.
4. Clean the filter and the filter chamber.
5. Check that the pump rotor moves freely.
6. Re-insert the filter and screwit in clockwise as far as it will go.
7. Reinstall the plinth.

Water supply hose
Check the supply hose regularly for brittleness and cracks and replace it if necessary using a new hose of the same type (available from After-Sales Service or a specialist dealer).

Mesh filter for water connection

Check and clean regularly. For washing machines with an inlet hose as shown in picture “D”,

1. Close the tap and loosen the inlet hose on the tap.
2. Clean the internal mesh filter and screw the water inlet hose back onto the tap.
3. Now unscrew the inlet hose on the rear of the washing machine.
4. Pull off the mesh filter from the washing machine connection with universal pliers and clean it.
5. Refit the mesh filter and screw the inlet hose on again.
6. Turn on the tap and ensure that the connections are completely water-tight.

Troubleshooting guide

Depending on the model, your washing machine is equipped with various automatic safety functions. This enables faults to be detected in good time and the safety system can then react appropriately. These faults are frequently so minor that they can be resolved within a few minutes.

mains plug is inserted into the socket

•  the wall socket is functioning correctly (use a table lamp or similar appliance to test it).

The washing machine will not start… and the “Start/ Pause” indicator lamp flashes.| •  the door is properly closed (child safety);

•  the “ Start/Pause ” button has been pressed;

•  the “Water tap closed” indication lights up. Open the water tap and press the “ Start/Pause ” button.

The appliance stops during the program (varies depending on the model).| • the door has been opened and the “ Start/Pause ” indicator lamp is flashing. Close the door and press the “Start/Pause” button again.

•  Check if there is too much foam inside, the machine enters the kill-foam routine. The machine will run again automatically after a period.

•  the washing machine’s safety system has been activated (see “Fault description table”).

Residue from detergent and additives left in the detergent drawer at the end of the wash.| •  the cover grid of the softener chamber and the separator of the main wash chamber are correctly installed in the detergent dispenser and all parts are clean (see “Care and maintenance”);

•  sufficient water is entering. The mesh filters of the water supply could be blocked (see “Care and maintenance”);

•  the position of the separator in the main wash chamber is adapted to the use of powder or liquid detergent (see “Detergent and additives”).

The machine vibrates during the spin cycle.| •  the washing machine is level and standing firmly on all four feet;

•  the transport bolts have been removed. Before using the machine, the transport bolts must be removed.

The final spin results are poor.| The washing machine has an imbalance detection and correction system. If individual heavy items are loaded (e.g. bathrobes), this system may reduce the spin speed automatically or even interrupt the spin completely if it detects too great an imbalance even after several spin starts, to protect the washing machine.

•  If the laundry is still too wet at the end of the cycle, remove some articles of laundry and repeat the spin cycle.

•  Excessive foam formation may prevent spinning. Use the correct amount of detergent.

•  Check that the spin speed selector has not been set to “0”.

---|---
If your washing machine has a time display: the programme time initially displayed is lengthened/shortened by a period:| This is a normal capacity of the washing machine to adapt to factors that can affect the wash programme time, e.g.:

•  excess foam formation;

•  load imbalance due to heavy items of laundry;

•  prolonged heating time due to reduced inlet water temperature;

Because of influences like these, the time remaining in the programme run is recalculated, and updated if necessary. In addition, during the filling phase,

the washing machine determines the load and if necessary adjusts the initial programme time displayed accordingly. During such update periods, an animation appears on the time display.

Enter the after-sales query mode

1. In the shutdown state, press the “ ” + “ ” + switch the “ ” to enter the after-sales inquiry mode;
2. It defaults to displaying the number of operation cycles;
3. Press “ ” to switch cycles/fault codes;
4. When querying fault codes, press the “ ” to page up and the “ ” to page down.

For Models with a Single Inlet

1. Fix the inlet hose to the cold water tap and the inlet valve on the rear side of the machine (Fig.1).

Ensure that:
All connections are tightly fixed.

WARNING!

• Do not allow children to operate, crawl on, be near or inside your washer.
• Note that during the wash cycles, the surface temperature of the porthole door may increase.
• Close supervision of children is necessary when the appliance is used near children.

Fault Code List

“F01” displayed on screen
The machine is not fed with water or insufficient water. Check:

• The faucet is fully open and has enough water pressure.
• The water inlet pipe is knotted or not?
• Filtering net of water inlet pipe is blocked or not (refer to maintenance and repair).

A water pipe is frozen or not
Press the “Start/Pause” key after the fault is removed. If a fault occurs again, please contact with after-sale service (refer to after-sale service.).

“F03” displayed on screen
The washer is not emptied. The washer stops the program from being executed. Shut down the machine and disconnect the power supply. Check:

• Drain pipe is knotted or not.

• Filter in the rain pump is blocked or not (refer to the cleaning of the later in the in pump)
  IMPORTANT: Ensure that the water has cooled before draining the appliance.

• The drain hose is frozen up.

  • Plug in the appliance again.
  • Select and start the “Spin” program or push the “Start/Pause” button for at least 3 seconds and restart the desired program.
  • If the fault occurs again, please contact After-Sales Service (see “After-Sales Service”).

Fault code
The washer stops when the program is running. The display window shows fault codes “F13”, “F14”, and “F24”, else fault codes from “F04” to “F98” or “Unb”.

If fault code “F13” is shown

• The door lock is abnormal.
• Start the program for 20 sec and unlock the washer door (PTC) to check whether the door is closed. Open or close it again.
• After the fault is removed, press the “Start/Pause” key. If a fault occurs again, disconnect the power supply and contact after-sale service.

If fault code “F14” is shown
Door open fault.

Action : Press the “Start/Pause” button. The washing machine will try to open the door. The alarm will not be removed until the door is unlocked. Or turn the nub off for 3 seconds to turn off the machine. Choose the desired program to start the machine. The alarm will be removed.

If fault code “F24” is shown

• The water level reaches the overflow level.
• Remove it by pressing the “Start/Pause” key and feed water.
• Select and start the required program. If a fault occurs again, disconnect the power supply and contact after-sale service.

If else fault code “F04” to “F98” is shown

• The electronic module fails.
• Turn the nub to Off for 3 seconds to turn off the machine.
• After the fault is removed, press the “Start/Pause” key. If a fault occurs again, disconnect the power supply and contact after-sale service.

If fault code “Unb” is shown
Unbalance alarms shall be solved by the following methods.

1. Laundry winding
   Turn the knob to “off” for 3 seconds for shutdown, open the door, shake the clothes and put them back into the washing machine, then select the single dewatering program to dry again.

2. Too light-weighted laundry
   Turn the knob to “off” for 3 seconds for shutdown, open the door, put in one or two towels, and then select the single dewatering program to dry again.

Before contacting After-Sales Service:

1. Try to remedy the problem yourself (see “Troubleshooting Guide”).
2. Restart the programme to check whether the problem has solved itself.
3. If the washing machine continues to function incorrectly, call After-Sales Service.

Transport/handing
Never lift the appliance by the worktop when transporting.

1. Pull out the mains plug.
2. Turn off the tap.
3. Disconnect the inlet and drain hoses.
4. Eliminate all water from the hoses and from the appliance (see “Removing the Filter”, “Draining Residual Water”).
5. Fit the transport bolts (obligatory).
6. The machine is over 55 kg in weight, two persons are needed to move it.

References

• valberg.de is available for purchase - Sedo.com
• Tienda de electrodomésticos y electrónica | ELECTRO DEPOT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>