CIRCONTROL CCL-eHOME Series Wallbox eHome User Manual

CIRCONTROL CCL-eHOME Series Wallbox eHome

Product Information

The Wallbox eHOME charging system is specially designed to be easily installed both in outdoor and indoor private car parks. It is used to charge all EV brands in MODE 3 (according to European standard IEC 61851-1). The charging can be done by connecting the tethered cable with a type 1 or type 2 connector or by connecting the EV cable into the charger socket type 2.

What’s included:

• Wallbox eHome Charge Point
• Installation Manual

Overview:

1. CIRCONTROL Logo
2. Status LED bar
3. Frontal cover
4. Model badge
5. Frame
6. Socket-outlet*
7. Protections and Meter Door
8. Cable + connector

(*) Plugs may vary depending on the model.

Product Usage Instructions

Charging Procedure

1. GREEN FIX BAR STATUS: The Wallbox eHOME has a status LED beacon. When it is green, it means that the unit is available and ready to start the charge.
2. PLUG: To start a new charge transaction, plug the Wallbox eHOME connector into your car and into the Charge Point if necessary (depending on the model).
3. BLUE DYNAMIC BLINKING LED STATUS: The status LED light bar turns blue, indicating that the Wallbox eHOME starts the charging process. While charging the EV, the LED light bar will continuously flash.
4. BLUE FIX LED STATUS: When the EV is fully charged, the charging process ends and the status LED light bar stops flashing and remains fixed in blue.
5. UNPLUG: At this moment, you can unplug the vehicle connector and the Charge Point if necessary.
6. GREEN FIX LED STATUS: Once the cable is disconnected, the LED light status bar turns back into green. In this status, the Charge Point is available to start a new charging process whenever it is required.

Status LED Light Errors

1. Blink Sequence 1: PILOT ERROR – When the Charge Point is connected to the EV, a Pilot short-circuit to earth may occur. Then, the status LED light bar turns red and flashes in a sequence of two blinks.
2. Blink Sequence 2: PROXIMITY ERROR – When the Charge Point is connected to the EV, a Proximity short-circuit to earth may occur. Then, the status LED light bar turns red and flashes in a sequence of three blinks.

Wallbox eHome

COPYRIGHT INFORMATION

• This document is copyrighted, 2020 by Circontrol, S.A. All rights are reserved. Circontrol, S.A. reserves the right to make improvements to the products described in this manual at any time without notice.
• No part of this manual can be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer.
• Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, or for any infringements upon the rights of third parties athat may result from its use.
• All other product names or trademarks are properties of their respective owners.

SHORT DESCRIPTION
The Wallbox eHOME charging system is specially designed to be easily installed both in outdoor and indoor private car parks, in order to charge all the EV brands of the market in MODE 3 (according to European standard IEC 61851-1), by just connecting either its tethered cable with a type 1 or type 2 connector or connecting the EV cable into the charger socket type 2.

What’s included:

Overview

1. CIRCONTROL Logo
2. Status LED bar
3. Frontal cover
4. Model badge
5. Frame
6. Socket-outlet*
7. Protections and Meter Door
8. Cable + connector

Operating Instructions

Charging procedure

1. GREEN FIX BAR STATUS The Wallbox eHOME has a status LED beacon. When it is in green colour, it means that the unit is available and ready to start the charge .
2. PLUG To start a new charge transaction, plug the Wallbox eHOME conector into your car and in the Charge Point if it is necessary ( depending on the model)
3. BLUE DYNAMIC BLINKING LED STATUS . The status LED light bar turns into blue, The WallBox eHOME starts the charging process, While charging the EV, the LED light bar will be flashing continuously.
4. BLUE FIX LED STATUS When the EV is fully charged, the charging process ends up and the status LED light bar stops flashing and remains fix in blue.
5. UNPLUG At this moment you can unplug the vehicle connector and of the Charge Point if it is necessary.
6. GREEN FIX LED STATUS Once the cable is disconnected, the LED light status bar turns back into green. In this status, the Charge Point is available to start a new charging process, whenever it is required.

Status LED light error’s

The Wallbox eHOME is capable to detect the following operating errors:

• Ventilation required error
• Control Pilot
• Proximity error
• Negative PWM error
• Maximum output current
• MiniDipswitch error
• Temperature error

Whatever the error case is, the Charge Point will stop charging and technical assistance will be required, except from the temperature error. In this last case, the Charge Point starts charging when the operating temperature is reached again.
In the following sections it will be explained how the Wallbox eHOME indicates the above-mentioned errors and the actions taken by the Charge Point.

1. VENTILATION REQUIRED ERROR In some old EVs, this state means that there are some gases coming out from the batteries. So, an external ventilation in the car park might be required. If it were the case, the status LED light would turn into red and keep blinking permanently.
2. PILOT ERROR When the Charge Point is connected to the EV, a Pilot short-circuit to earth may occur. Then, the status LED light bar turns into red and flashes in a sequence of two blinks.
3. PROXIMITY ERROR When the Charge Point is connected to the EV, a Proximity short-circuit to earth may occur. Then, the status LED light bar turns into red and flashes in a sequence of three blinks.
4. NEGATIVE PWM VOLTAGE ERROR When the Charge Point is connected to the EV, the PWM signal, used to communicate the Charge Point with the EV, can be negative. Then, the status LED light bar turns into red and flashes in a sequence of four blinks
5. MAXIMUM OUTPUT CURRENT ERROR. If this on-board current limit selection is not set up according to the hardware features, the Charge Point detects it and shows this error. In this case, the status LED light bar turns into red and flashes in a sequence of five blinks..
6. TEMPERATURE ERROR When the Charge Point temperature is below a certain value, it is detected by the Charge Point. In this situation, the status LED light bar turns into orange blinking.In the meantime, if the Charge Point is supplied with heater (optional), it starts heating the inside components until the operating temperature is reached. Then the Charge Point starts charging again.

Firmaware Version
FIRMWARE VERSION When the unit is booting, the LED bar will show the firmware version in orange. The first digit of the version will be shown as a certain number of blinking of the first LED, as many times as the digit indicates, and the second digit will be displayed by the last LED blinking accordingly to what the second digit indicates (i.e. for version 1.6, you will see one blink at the first LED and six at the last LED).

Need help?
In case of any query or need further information, please contact our Post- Sales Department.

• support@circontrol.com
• circontrol.com
• (+34) 937 362 940
• (+34) 937 362 941

References

• EV Charging and Efficient Parking - CIRCONTROL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>