SHINE B A-01 Bathroom Assistant Cleans Your Toilet Automatically User Guide
- June 6, 2024
- SHINE
Table of Contents
Get Ready to Shine
Bathroom Assistant Manual
Model: SHINE-BA-01
Before You Begin
Download the Shine Bathroom App
The app is available to download for free from the App Store or Google Play. You can get links to download the app at www.shinebathroom.com/shineapp
Quick Start Guide
Download the Shine Bathroom App
Download the Shine Bathroom App and create your account to get started. Follow
the on-screen instructions to complete the setup of your Bathroom Assistant.
Clean Toilet Bowl Rim
Using the supplied wipe, clean the rim of your toilet bowl. It is important
to have a clean surface to attach the spray bar to.
Allow the rim to dry for 3 minutes.
Attach Spray Bar & Water Sensor
This pre-measured pod is what helps us create our powerful cleaning
solution. A single pod should provide enough cleaning solution for an entire
month.
Power On Device
Twist the battery into the unlock position and remove the protective film.
Afterwards, power on the device by twisting the battery into the lock
position, the LEDs will light up.
Inside the Box
(A) Assistant Body (x1)
(B) Battery (x1)
(C) Spray Bar (x1)
(D) Water Sensor (x1)
(E) Cleaning Pod (x3)| Assistant Lid (x1)
Spray Tubing (x1)
Adhesive Tab (x1)
Alcohol Wipe (x1)
User Manual (x1)
---|---
BEFORE YOU BEGIN:
Download the Shine Bathroom App from the App Store (iOS) or Google
Play (Android) and create an account using the email address you used to
purchase your device. Once you’ve created and verified your account, the
app will take you through the steps below to set up your new device.
Setup Instructions
-
Remove the Bathroom Assistant and accessories from the box.
Carefully remove the packing materials, being careful not to pull on the Water Sensor or Spray Bar as they’re attached to the Bathroom Assistant. Remove the Bathroom Assistant and accessories and place them on a flat surface. -
Place and install the Bathroom Assistant and Water Sensor (D).
You can place the Bathroom Assistant anywhere near your toilet, your only limitation is the length of the Spray Bar tubing and Water Sensor cable. Take the Water Sensor and clip it onto the outside of your toilet’s water inlet pipe (it’s the line typically found under the tank coming from the floor or wall).
Carefully wipe down the center backside of your toilet’s rim with the included alcohol wipe. Let the area dry for at least 3 minutes before continuing. -
Install the Spray Bar (C).
Peel away the backing on the double-sided tape and position the Spray Bar where you want to mount it. Securely install by firmly pressing the Spray Bar down on the rim of the toilet for 30 seconds.
Optimal placement is the middle on the backside of your toilet rim (see black oval in diagram). You can place the Spray Bar anywhere in the back quarter of the toilet bowl rim and still be effective. -
Remove the Battery and peel away protective film; replace Battery to turn on the device.
On the side of the device, you’ll see two lock icons rotate the battery while holding the Assistant Body to line up the “unlocked” icon with the line on the battery below it. Remove the protective film, and then rotate the battery pack back into the “locked” position. The device should light up indicating it’s on and ready to pair. -
Fill the Bathroom Assistant with water. Using a measuring or drinking cup, add 1,000 ml of water through the opening at the top. The water level should be above the vents in the center column.
-
Open the Shine Bathroom App and create an account to finish the setup process.
You will complete the setup process by following the directions in the app.
Certain features of the Bathroom Assistant require a compatible mobile device
and active Shine App customer account. For example, scheduling toilet cleaning
times requires an active account and a compatible mobile device. The Shine
Bathroom Assistant requires a Wi-Fi Network and a compatible mobile device.
Minimum OS requirements are available at
shop.shinebathroom.com/pages/req.
Availability and performance of certain features and services are service-,
device-, and network-dependent and may not be available in all areas.
Subscription(s) may be required, and additional terms, conditions and/or
charges may apply. The Shine
Bathroom Assistant is optimized for official Shine Cleaning Pods only. All
features, functionality, and other product specifications are subject to
change without notice or obligation. © Shine Bathroom Technologies, Inc. Shine
Bathroom, Shine Bathroom Assistant, SAM (Shine Automation Manager), and their
respective logos are trademarks of Shine Bathroom Technologies, Inc. Other
trademarks and trade names are those of their respective owners. All rights
reserved. For compliance and certification information including technical
data, FCC statements, and individual country notices visit the following
website
http://www.shinebathroom.com/compliance.
Operating Information:
Recommended Battery Charging Temperature Range: 5-35°C (Conducive to Cell
Protection)
Product Temperature Range: 0 – 45°C (For Water Pump Operation)
Storage Temperature: -10 – 60°C
Support
Need help getting started? Have questions about your device?
Our team is ready to answer any questions and help get you going with your
Bathroom Assistant.
Email Us
team@shinebathroom.com
Chat With Us
Available at www.shinebathroom.com
Call or Text Us
+1 (805) 272 – 7600
Call, Message, and Data rates may apply.
Mounts & Accessories
See the latest mounts and accessories for your Bathroom Assistant by visiting www.shinebathroom.com today.
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provided with antenna
installation instructions and consider removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
The instructions for appliances having a part of class III construction supplied from a detachable power supply unit shall state that the appliance is only to be used with the power supply unit provided with the appliance. The instructions for class III appliances shall state that it must only be supplied at safety extra low voltage corresponding to the marking on the appliance. This instruction is not necessary for battery-operated appliances if the battery is a primary battery or secondary battery charged outside of the appliance.
The instructions shall give information regarding charging. The instructions for appliances incorporating batteries that are intended to be replaced by the user shall include the following:
- the type reference of the battery;
- the orientation of the battery with regard to polarity;
- the method of replacing batteries;
- details regarding safe disposal of used batteries;
- warning against using non-rechargeable batteries;
- how to deal with leaking batteries.
Instructions for appliances containing non User-replaceable batteries shall state the substance of the following:
The appliance contains batteries that are only replaceable by skilled persons.
Instructions for appliances containing non-replaceable batteries shall state
the substance of the following:
This appliance contains batteries that are non-replaceable.
Replacement:
The instructions shall contain the quantity and details of the electrolyte to
be used and details of the chemical reactions that occur in the electrolyser.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>