babymoov A047014 Hygro Plus Cool Mist Humidifier Instruction Manual
- June 16, 2024
- babymoov
Table of Contents
babymoov A047014 Hygro Plus Cool Mist Humidifier
Product Information
Specifications
- Rated voltage (alternating current): 120 V / 60 Hz
- Power : 25 W
- Vapour flow rate : 8.5 fl oz./hour (250 ml/hr maximum)
- Water tank capacity : 0.7 gallon (2.5 litres)
- Suitable for a room 90 sq. ft. to 220 sq. ft. (8 – 20 m2)
- Maximum autonomy : 22 hours
- Humidity sensor setting range : 30 to 90 %
- The recommended humidity level for a child’s bedroom is 40 to 50 %
Composition
- Cover
- Essential oil diffuser cup
- Water tank
- Valve
- Base
- Humidity sensor
- Power supply
- Power cord
- Air exit (ventilation)
Quick Start
- Step 1: Fill the water tank (maximum 0.7 gallon / 2.5 l), close the valve tightly, then set it on the base.
- Step 2: Plug in to a wall socket, press the ON button, then select the desired quantity of steam using the +/- buttons.
- Step 3: Your Hygro+ humidifier is ready! It’s already producing pure and cool vapor throughout the entire room.
Product Usage Instructions
Hygro+ Humidifier Function
The Hygro+ humidifier function allows you to adjust the humidity level in
the room where it is installed. The recommended humidity level for your
child’s bedroom is between 40% and 50%.
Manual Mode
- Remove the humidifier cover (1) and remove the essential oil diffuser (2).
- Remove the water tank (3) from the humidifier base.
- Turn the water tank upside down and unscrew the water tank cap (4).
- Fill the tank with tap or distilled water. Note: Use cold water, maximum 0.7 gallon (2.5 l). Do not use hot water.
- Screw the water tank cap back on the water tank and set it on the humidifier base.
Frequently Asked Questions
- Q: What is the recommended humidity level for a child’s bedroom?
- A: The recommended humidity level for a child’s bedroom is between 40% and 50%.
Instructions for use
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING
You must observe the following precautions each time you use an electrical
appliance, especially when children are present. Please install the Hygro+ far
away from children.
- Please read these instructions carefully before turning on your Hygro+.
- Ensure that the voltage shown on the appliance corresponds to the voltage in your home.
- To avoid electric shock: never immerse the Hygro+, the cord or the plug in water or any other liquid.
- Never use the Hygro+ for anything other than the purpose for which it has been designed. Any other use must be considered dangerous and inappropriate.
- If you notice that the Hygro+, plug or power supply cord has been damaged, disconnect the Hygro+ immediately and do not use it again. Repairs must be carried out by a qualified person.
- The Hygro+ does not contain any parts for user maintenance. Do not dismantle it.
- You must be extremely vigilant when using the Hygro+ in the presence of children.
- Never use the Hygro+ without water.
- Never add detergent, chemical products or perfume.
- Always use cold water. We recommend using distilled water, which will ensure optimal use of the spray and the water sensor.
- Do not leave the power supply cord at the edge of a table or worktop. Do not place it on a hot surface.
- Position the Hygro+ on a stable and even surface, away from sunlight.
- Never touch the transducer with your fingers or with a metal object.
- Never move the Hygro+ when it contains water or when it is switched on.
- Do not leave water in the tank for too long: this can encourage the formation of bacteria.
- Unplug the HYGRO+ when not in use, before filling it, cleaning it or storage.
- For domestic use only. Do not use outside the home.
WARNINGS
- If the power supply cable gets damaged it must be replaced by the manufacturer, the after-sales service or people with similar qualifications, in order to avoid any risk of danger.
- This appliance isn’t meant to be used by people (including children) whom physical, mental, sensory capacities are reduced, or people lacking of experience or knowledge, unless the person responsible for their safety has supervised and instructed them in the use of this appliance.
- Children should be supervised to ensure that they do not play with the appliance.
SAFETY INSTRUCTIONS THAT MUST BE FOLLOWED
- You must be extremely vigilant when the Hygro+is used in the presence of children.
- Children cannot recognize the hazards associated with the usage of electrical appliances. For this reason, always supervise children when they are near the Hygro+.
- Never place the Hygro+ near a hot surface, in a hot oven, or close to electric or gas hot-plates.
- Do not place the appliance directly on the floor or next to a heating vent. If the mist comes in contact with the floor prior to evaporating, the floor surface can become damaged.
- Place appliance where it is not easily knocked over.
- Only operate the humidifier when it is completely assembled.
- Do not run power cords under carpets, and do not cover with throw rugs. Arrange cord so that it will not be tripped over.
- Never pull the plug from the outlet by the cable or with wet hands.
- Do not use the appliance where combustible gases or vapors are present.
- Do not expose the appliance to rain, or use near water, in a bathroom, laundry area or other damp location.
- This unit must be used in its upright position.
- Do not allow foreign objects to enter ventilation or exhaust opening as this may cause electric shock or damage to the appliance. Do not block air outlets or intakes.
- Do not pour water into the mist outlet of the appliance.
- To protect health safety and proper humidifier function use only clean, contamination-free, cold, fresh tap water in your humidifier. If your water source is contaminated or if you are uncertain of its safety use distilled water. In addition, it is advised to clean and maintain your humidifier in a timely manner as instructed in this manual.
SAVE THESE INSTRUCTIONS
Overview
Thank you for choosing Hygro+ to provide your Baby with pure and healthy air. Here’s how it works.
COMPOSITION
- Cover
- Essential oil diffuser cup
- Water tank
- Valve
- Base
- Humidity sensor
- Power supply
- Power cord
- Touch screen
- Humidity level and timer
- Temperature (°F / °C) and timer
- Steam rate display
- Increase steam rate (1 to 5)
- Decrease steam rate
- Programming
- On/Off button
- Night light
- Water level indicator
- Air exit (ventilation)
QUICK START
- Step 1 Fill the water tank (maximum 0.7 gallon / 2.5 l), close the valve tightly, then set it on the base.
- Step 2 Plug in to a wall socket, press the ON button, then select the desired quantity of steam using the +/- buttons.
- Step 3 Your Hygro+ humidifier is ready! It’s already producing pure and cool vapour throughout the entire room.
TECHNICAL CHARACTERISTICS
- Rated voltage (alternating current): 120 V / 60 Hz
- Power : 25 W
- Operating temperature : 32 °F – 104 °F (0 – 40 °C)
- Vapour flow rate : 8.5 fl oz./hour (250 ml/hr maximum)
- Water tank capacity : 0.7 gallon (2.5 litres)
- Suitable for an room 90 sq. ft. to 220 sq. ft. (8 – 20 m2)
- Maximum autonomy : 22 hours
- Humidity sensor setting range : 30 to 90 %
- The recommended humidity level for a child’s bedroom is 40 to 50 %
HUMIDIFIER FUNCTION
Hygro+’’s humidifier function lets you adjust the humidity level in the room
in which it is installed.
N.B.: The recommended humidity level for your child’s bedroom is between
40 % and 50 %.
MANUAL MODE
- Remove the humidifier cover (1) and remove the essential oil diffuser (2).
- Remove the water tank (3) from the humidifier base.
- Turn water tank upside down and unscrew water tank cap (4).
- Fill the tank with tap or distilled water.
N. B.: cold water – maximum 0.7 gallon (2.5 l.). Do not use hot water.
Screw water tank cap back on water tank and set on the humidifier base.
N. B.: wait a few seconds before the base of the humidifier is filled
with water. The Babymoov logo on the water tank must be facing outward.
Replace the essential oil diffuser (2) in the centre of the chimney, and
replace the cover (1) on the water tank.
N. B.: the essential oil diffuser must be positioned point down.
- Plug your Hygro+ humidifier into a wall outlet using the power cord, and press the ON button .
- Select the desired quantity of steam using the +/- buttons, then point the steam output in the desired direction using the cover (1).
- 1st level : steam flow rate = 3.7 fl oz./hour (110 ml/hour)
- 2nd level : steam flow rate = 5 fl oz./hour (150 ml/hour)
- 3rd level : steam flow rate = 6 fl oz./hour (180 ml/hour)
- 4th level : steam flow rate = 7.3 fl oz./hour (220 ml/hour)
- 5th level : steam flow rate = 8.3 fl oz. (250 ml/hour)
The steam flow rate is automatically reset to the last setting when the humidifier is unplugged or turned off.
N.B.: ensure that the steam is not directed toward a wall socket or other electrical device.
- Your Hygro+ humidifier is ready to use! It’s already producing pure, cool vapour throughout the entire room.
- To shut off the humidifier, simply press the OFF button .
N.B.: after 30 seconds of inactivity, the screen automatically switches to stand-by mode. To reactivate it, simply press the ON button.
WATER QUANTITY AND TIME OF USE
N.B.: the amount of water in the water tank and the selected steam flow
rate determine how long the humidifier will run. The Hygro+ humidifier is
designed for 22 hours of maximum autonomy.
The water level indicator turns on when there is insufficient water in the
tank.
SETTING THE HYGROMETRY LEVEL WITH NO COUNTDOWN
- Press during 3 seconds to set the automatic stop of Hygro+.
- «90%» flashes. Press + /- to select the appropriate hygrometry level.
- Press for 3 seconds to enter the setting and activate the setting.
- becomes blue. The current humidity level of the room is displayed.
- Your Hygro+ humidifier will automatically stop once the requested humidity level is reached.
- Press briefly to check the setting.
- The hygrometry level is displayed for 3 seconds.
How to change the setting
- Press for 3 seconds. The last setting flashes on the display.
- Press + /- to select a new hygrometry level.
- Press for 3 seconds to enter and activate the new setting. .
- becomes blue. The current hygrometry level of the room is displayed.
To disable the auto setting and go back to manual mode, press «ON/OFF» for 5 seconds. auto becomes white again..
SETTING THE HYGROMETRY LEVEL WITH A COUNTDOWN
In order to set the automatic stop of Hygro+, press auto for 3 seconds.
-
«90%» flashes. Press + /- to select the appropriate hygrometry level.
-
Briefly press : «00:00» is displayed and flashes. Press «+ /-» to set the timer with 30-minute brackets (e.g.: 00:30 / 01 :00 / 01 :30, etc.).
N. B.: a longer pressure on «+/-» will help you set the timer faster. -
Press for 3 seconds to enter and activate the new setting.
becomes blue. The current hygrometry level of the room is displayed (02:30 means the humidifier will start in 2 hours and 30 min).
Your Hygro+ humidifier will automatically stop once the requested humidity level is reached OR when the timer reaches «00:00».
Press briefly to check the setting.
The hygrometry level is displayed for 3 seconds. The timer will then appear for 3 seconds before the initial display appear.
How to change the setting
-
Press for 3 seconds. The last setting flashes on the display.
-
Press + /- to select the appropriate hygrometry level.
-
Briefly press : «00:00» is displayed and flashes. Press «+ /-» to set the timer with 30-minute brackets (e.g.: 00:30 / 01 :00 / 01 :30, etc.).
N. B.: a longer pressure on «+/-» will help you set the timer faster. -
Press for 3 seconds to enter and activate the new setting.
becomes blue. The current hygrometry level of the room is displayed.
To disable the setting and go back to manual mode, press «ON/OFF» for 5 seconds. becomes white again. N.B.: when you set up a hygrometry rate (ex: 55 %), the mist diffusion will stop one the rate is reached and will restart when the rate will be lower of 6 % than the programmed rate.
DIFFUSING ESSENTIAL OILS
You can also diffuse essential oils with Hygro+.
Simply place a few drops of essential oil in the cup (2) and turn on the steam
function.
ATTENTION
- Never pour essential oil directly into the water tank or chimney.
- Consult your physician for advice on suitable essential oils depending on your child’s age.
- Keep essential oils out of children’s reach.
- Consult your physician immediately if swallowed.
Essential oils can damage the humidifier. Do not put more than three drops of essential oils in the diffuser cup . After each use, use a damp cloth to remove residues of essential oils.
NIGHT LIGHT FUNCTION
- The Hygro+ night light function has seven different colours.
- Press the night light button to turn on the night light.
- The night light changes colour each time you press the night light button
To automatically change colours (rainbow function), press the night light button for 3 seconds.
THERMOMETER FUNCTION
Hygro+’’s thermometer function lets you display the temperature in the room
in which it is installed.
N.B.: to switch the temperature unit (°C / °F): press for 3 seconds on
«+» and «–» at the same time. The recommended temperature for your child’s
bedroom is between 67 and 70 °F (19 and 21 °C).
CARE AND PRECAUTIONS FOR USE
- Follow these cleaning procedures to guarantee proper and efficient operation. Good maintenance is essential for the humidifier’s long life and to prevent the proliferation of bacteria in the water, inside the water tank, or in suspension. Do not leave water in water tank when it is not use.
- Always unplug the humidifier before cleaning and wait until the base has cooled.
- Wipe the humidifier with a soft damp cloth or sponge. Allow it to air dry. Never immerse the base in water or any other liquid.
- Clean the water tank regularly with a mix of chlorine bleach and water.
- Rinse with water and allow it to air dry.
- Never use detergents to clean any parts of the humidifier intended to contain water. A cloud of detergent dissolved in the water could interfere with vapour production.
- Remove the base regularly. Pour 8.3 fl oz. (250 ml) of pure white vinegar into the base. Let it sit for 20 minutes while you clean all the internal surfaces using a soft brush.
- Gently scrub all parts around the transducer using a soft brush. Do not press directly on the transducer. Empty the vinegar solution into the sink. Rinse with clean hot water.
- Never use cleaning agents, solvents or abrasive substances as they could damage the humidifier and its surfaces.
- Before storing, empty the water tank and any water in the base, respecting the icon indicating how to pour the water. Ensure all parts are completely dry, then loosen the plug to prevent the joint from sticking.
FREQUENTLY ASKED QUESTIONS
-
Should I add hot or boiling water to the tank to improve vapour production?
No, doing so could permanently damage your humidifier. Hygro+ produces cold steam using ultrasounds, so it does not need hot water. Add cold water or water at room temperature. -
Some water is left in the tank. Should I empty it?
Yes. We recommend to empty the unit daily to prevent the formation of mould or the proliferation of bacteria inside the tank. When you do not plan to use the humidifier for an extended time, empty any water and let the humidifier air dry before storing.
ALT Group Babymoov Corp. 46 Route 156, Suite 8 YARDVILLE, NJ 08620 USA
www.babymoov.com
Hotline: 1-855-517-2456
Designed and engineered by Babymoov in France
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>