cellgate W482 Series IP Telephone Entry and Access Control Installation Guide

: June 16, 2024
: Cellgate

Table of Contents

cellgate W482 Series IP Telephone Entry and Access Control
Product Information
Product Usage Instructions
Items Included in Kit
Wiring Examples
Interface Circuit Board
VPN Connection
Wiring
Interface Wiring Diagram
Magnetic Switch Setup
Mounting to Standard
Read User Manual Online (PDF format)
Download This Manual (PDF format)

cellgate W482 Series IP Telephone Entry and Access Control

Product Information

Specifications
- Product Model: W482 Series
- Product Number: AA1MLPE VPN
- Power Supply: 12 Volt DC
- Recommended Wiring: 18/6 shielded for the main device, 18/4 shielded for optional Wiegand devices
Items Included in Kit
- Watchman 480 Unit
- 12 Volt DC Power Supply
- Magnetic Read Switch
- Keys
- Nuts x 4
- Bolts x 4
- Install Guide
- Customer Information Packet

Product Usage Instructions

Power Supply Wiring
- To connect the power supply, follow these steps:
- Wire the main power from the transformer to the power connector on the circuit board.
- Connect the gate trigger wires from the Normally Open (NO) and Common (C) terminals to the free-exit or exit terminals on the gate operator.
- Connect the gate status wires on the 6 pin connector on the main relay and input plug to the magnetic switch or a Dry Contact, Normally Closed (NC) relay on the gate operator.
- If using an optional 26-bit reader (e.g., keypad, card reader, RFID, clicker), wire the device to the Wiegand connection on the interface circuit board.
- If adding an external camera, refer to the Camera Guide for wiring instructions.
- Test and activate the system using the test credentials provided in the Activation & Test Process document.
Magnetic Switch Setup
- To set up the magnetic switch, follow these steps:
- Place the Mag Switch anywhere that allows A and B to be pulled at least 2 inches away from each other when the gate is open and within 1.5 inches when the gate is closed.
FAQ
- Q: What wiring should I use for the main device and optional Wiegand devices?
- A: We recommend using 18/6 shielded wiring for the main device and 18/4 shielded wiring for optional Wiegand devices.
- Q: Can I remove the SIM card from the in-hand modem?
- A: No, please do not remove the SIM card from the in-hand modem.
- Q: How should I wire for solar power?
- A: Please refer to the Wiring for Solar Power section in the user manual for detailed instructions.

Items Included in Kit

The following items are included in your W480 delivery.

Watchman 480 Unit
12 Volt DC Power Supply
Magnetic Read Switch
Keys
Nuts X 4
Bolts X 4
Install Guide
Customer Information Packet

NOTE Leave one key with the customer.

Wiring Examples

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $1$$

Recommended wiring: 18/6 shielded for main device, and 18/4 shielded for optional Wiegand devices.

Interface Circuit Board

The circuit board is oriented the same as the Watchman install. If you requested an expansion board, we installed it.
We recommend the following gauges (ga) for each distance:

18 ga stranded: up to 25 ft
16 ga stranded: up to 50 ft
12 ga stranded: up to 60 ft

VPN Connection

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $3$$

Product Numbers: AA1MLPE VPN

The VPN connection ships DHCP enabled and does not support external cameras.
In the image to the left, the black chord is the Ethernet connection.

NOTE

Ethernet connection is required.
Do not remove SIM card from the in-hand modem.

Wiring

Wiring with Transformer

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $4$$

Wiring for Solar Power

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $5$$

Interface Wiring Diagram

Oriented the same as the Watchman install

The supplied diode must be used for all magnetic lock installations, or the warranty is voided.

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $6$$

Dry Contact Relay, Normally Open Dry Contact No Voltage to Lock or Gate

Dry Contact Relay, Normally Closed Dry Contact No Voltage to Lock or Gate

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $8$$

Lock Requiring Constant 12 V: Wet Contact Relay, Normally Open Door/lock opens (releases) when power is added.

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $9$$

Lock Requiring Constant 12 V: Wet Contact Relay, Normally Closed

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $10$$

Wiegand Wiring to Board and Direct to Faceplate, 26 Bit Reader To Interface Board

$cellgate-W482-Series-IP-Telephone-Entry-and-Access-Control-featuredfig-1 $11$$

Magnetic Switch Setup

The Mag Switch can be placed anywhere that allows A and B to be pulled at least 2 inches away from each other when the gate is open and within 1.5 inches when the gate is closed.

NOTE