PARMIDA PLED-CSTR27K-24V-KIT Dimmable COB LED Strip Light Kit Instruction Manual
- June 16, 2024
- PARMIDA
Table of Contents
PARMIDA PLED-CSTR27K-24V-KIT Dimmable COB LED Strip Light Kit
Product Information
Specifications
- Model Numbers: PLED-CSTR27K-24V-KIT, PLED-CSTR3K-24V-KIT, PLED-CSTR4K-24V-KIT, PLED-CSTR5K-24V-KIT, PLED-CSTR6K-24V-KIT
- Power Supply: 24V DC isolated power supply
- Compatible Class 2 DC Constant Voltage LED Driver (power supply) required
Safety Instructions:
- Turn off power before installation or servicing to reduce the risk of electric shock.
- Install the luminaire in accordance with local and National Electrical Code (N.E.C). Consult a qualified electrician if you are not familiar with these codes and requirements.
- Verify the availability of necessary tools and incidental materials.
- Use a 24V DC isolated power supply with a compatible Class 2 DC Constant Voltage LED Driver (power supply) to operate the LED Strip Light.
- Avoid bending the Strip Light past a diameter of 60 mm or less to prevent damage.
- Handle the Strip Light with care to avoid excessive handling, bending, and pressure that may damage the product.
- Always disconnect the LED Strip Lights from the power source before cutting or connecting.
Unpacking:
Thoroughly inspect the light for freight damage. Report any freight damage to
the delivery carrier.
Installation:
Ensure the surface is clean, dry, and smooth before installing the Strip
light. Remove the adhesive backing from the strip and press firmly into place,
smoothing the adhesive strip against the installation surface.
Cutting the Strip Light:
If you choose to cut the LED Strip Light, make sure it is disconnected from
the power source before cutting. Carefully cut the LED Flex strip along the
dashed line. Failure to cut along the dashed line could result in injury or
product damage. This Strip Light can only be cut every 2 inches.
Voltage Drop:
Voltage drop is the normal loss of voltage that occurs as current flows along
a wire connection in low voltage systems. This can lead to a gradual lower
lumen output and a general reduction in light quality. Factors such as wire
length, thickness, and wattage can influence the amount of voltage drop that
occurs. If connecting multiple Strip Lights, it is not recommended to connect
more than 22.96 ft due to voltage drops that lead to gradual lower lumen
output along the Strip Light.
Troubleshooting:
If the LED Strip Light does not turn on, follow these steps:
- Ensure the power supply is turned on and receiving power.
- Confirm correct polarity (+ to + and – to -) when joining the LED Strip/Tape and when connecting them to the Drivers.
- Make sure the output voltage of the Driver matches the input requirement of the LED Strip Light.
- Check all LED connections and ensure accessories are properly used.
FAQ:
-
Q: What is the maximum length I can cut the LED Strip Light?
A: The LED Strip Light can be cut every 2 inches. -
Q: Can I connect multiple Strip Lights together?
A: Yes, you can connect multiple Strip Lights together. However, it is not recommended to connect more than 22.96 ft due to voltage drops that lead to lower lumen output along the Strip Light. -
Q: What should I do if the LED Strip Light does not turn on?
A: Ensure the power supply is turned on and receiving power. Confirm correct polarity when joining the LED Strip/Tape and when connecting them to the Drivers. Make sure the output voltage of the Driver matches the input requirement of the LED Strip Light. Check all LED connections and ensure accessories are properly used.
IMPORTANT:
When using electrical equipment, basic safety precautions should always be
followed as below:
SAFETY INSTRUCTIONS
READ AND FOLLOW BELOW SAFETY INSTRUCTIONS
- To reduce risk of electric shock, turn off power before installation or servicing.
- This luminaire must be installed in accordance with local and National Electrical Code (N.E.C). If you are not familiar with these codes and requirements please consult a qualified electrician.
- Verify the availability of necessary tools and incidental materials.
- A 24V DC isolated power supply must be used to operate the LED Strip Light. This product must be powered with a compatible Class 2 DC Constant Voltage LED Driver (power supply).
- To avoid damaging the Strip Light, do not bend the Strip Light past a diameter of 60 mm or less.
- The Strip Light must be handled with care. Excessive handling, bending, and pressure may damage the product.
- Always disconnect the LED Strip Lights from the power source before cutting or connecting.
UNPACKING:
Thoroughly inspect the light for freight damage. Freight damage should be
reported to the delivery carrier
PACKAGE CONTENTS
- 1 x 16.4 ft COB Strip Light
- 1 x Power Supply
- 2 x Clip connector
- 1 x Remote
INSTALLATION
- Ensure the surface is clean, dry, and smooth before installing the Strip light.
- Remove adhesive backing from strip then press firmly into place, smoothing the adhesive strip against the installation surface.
CUTTING THE STRIP LIGHT:
If you choose to cut the LED Strip Light, ensure the Strip Light is
disconnected from power source before cutting the strip. Carefully cut the LED
Flex strip where shown by the dashed line. Failure to cut the strip along the
dashed line could result in injury or product damage. This Strip Light can
only be cut every 2 in.
LINKING ACCESSORIES – CLIP CONNECTOR:
If you choose to link the LED Strip Lights, attach the Strip Lights using the
clip connector accessory. Insert each end of the connecting Strip Lights into
the clip as shown – positive terminal to positive terminal. Press the top of
the clip down firmly to secure the connection.
VOLTAGE DROP:
Voltage drop is the normal loss of voltage that occurs as current flows along
a wire connection in low voltage systems which can lead to a gradual lower
lumen output, and general reduction in light quality. Wire length, thickness,
and wattage can influence the amount of voltage drop that occurs. If
connecting multiple Strip Lights, connecting more than 22.96 ft is not
recommended due to voltage drops that lead to gradual lower lumen output along
the Strip Light.
REMOTE CONTROL
CLIP CONNECTOR
TROUBLE SHOOTING
LED STRIP LIGHT DOES NOT TURN ON
- Ensure the power supply is turned on and receiving power.
- Confirm you have maintained correct polarity (+ to + and – to -) when joining the LED Strip/Tape as well as when they are connected to the Drivers.
- Ensure that the output voltage of the Driver matches the input requirement of the LED Strip Light.
- Check all LED connections, and ensure accessories are properly used.
ONLY PART OF THE LED STRIP LIGHT IS LIT
- Check the connection and ensure accessories are properly used on the area of the Strip Light that is not lit up.
- Confirm you have maintained correct polarity (+ to + and – to -) when joining the LED Strip/Tape as well as when they are connected to the Drivers.
- If part of the LED Strip is accidentally damaged you may cut and remove that section and connect the remainder of the Strip Light together.
LED STRIP LIGHT IS BLINKING
- Ensure a compatible driver is being used, a 24V driver is required.
Contact Information
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>