S1000R Series Oil Cooler Guard Instruction Manual

: June 16, 2024
: R G

Table of Contents

S1000R Series Oil Cooler Guard
Product Information
Product Usage Instructions
LEGEND
FITTING INSTRUCTIONS
contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

S1000R Series Oil Cooler Guard

Product Information

Specifications:

Item No.: OCG0049PRO
Item 1: OCG0049 Oil Cooler Guard
Item 2: Rubber Grommets
Quantity: Item 1 – 1 piece, Item 2 – 2 pieces

Product Usage Instructions

Step 1: Check Parts

Before proceeding with the installation, ensure that all parts are present. Refer to the labeled pictures on Page 2 for clarity. If any parts are missing, do not proceed with the installation.

Step 2: Torque Settings

Use the following torque settings when tightening bolts:

M4 Bolt: 8Nm
M5 Bolt: 12Nm
M6 Bolt: 15Nm
M8 Bolt: 20Nm
M10 Bolt: 40Nm
M12 Bolt: 40Nm

Step 3: Mounting Instructions

Please note that the way the kit is packed may not represent the way of mounting to the bike. Follow the instructions below:

Position the OCG0049 Oil Cooler Guard on the designated area of your bike.
Insert the Rubber Grommets into the corresponding holes on the Oil Cooler Guard.

Step 4: Final Steps

Once you have mounted the Oil Cooler Guard and inserted the Rubber Grommets, make sure all components are securely fastened. Double-check the torque settings to ensure proper tightness.

FAQ

Q: Where can I find digital copies of these instructions?
A: Digital copies of these instructions are available for download at www.rg-racing.com.
Q: What should I do if I have any doubts or need assistance during the fitting process?
A: If you have any doubts or need assistance, it is recommended to consult one of our dealers or have the product fitted by a qualified technician.
Q: Can I throw away the rubber washers used to hold components onto bolts?
A: Yes, the rubber washers can be thrown away if they are used to hold components onto bolts.

THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING. IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.

PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE. IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS, THESE RUBBER WASHERS CAN BE THROWN AWAY.

TOOLS REQUIRED

· Set of Torx keys

| GENERAL TORQUE SETTINGS

M4 BOLT = 8Nm M5 BOLT = 12Nm M6 BOLT = 15Nm M8 BOLT = 20Nm M10 BOLT = 40Nm

M12 BOLT = 40Nm

---|---

LEGEND

ITEM NO.	DESCRIPTION	QTY
ITEM 1	OCG0049 OIL COOLER GUARD	1
ITEM 2	RUBBER GROMMETS	2

FITTING INSTRUCTIONS

Push the 4x rubber grommets (Item 2) into the 4x holes in the corners of the oil cooler guard (Item 1) making sure the pointed ends of the grommets are facing OUTWARDS (towards the front wheel when the guard is installed).
Remove the RHS & LHS fairing, refer to the owner’s manual if necessary.
Remove the 2x bolts joining the radiator guard to the oil cooler, as shown in Picture 1.
Slide the lower hooks over the underside of the oil cooler, as shown in Picture 2.
Position the oil cooler guard tabs between the radiator and oil cooler joining points as shown in Picture 3.
Secure with the original bolts & refit all panels

See more R &G products for your Motorcycle in the link below: R&G Racing | All Products for BMW – S1000RR (2023) (rg-racing.com)

CONSUMER NOTICE The catalog description and any exhibition of samples are only broad indications of the Products and R&G may make design changes that do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned directly to us if they were purchased directly from us (customer must prove if necessary). Otherwise to be returned to the original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at the time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty good