Pro Water Tank
With Mounting System 42L
WTAN073

FWTAN073 Pro Water Tank Mounting System

READ ME !
Thank you for purchasing a Front Runner 42L Pro Water Tank Strap.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.

IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

**** CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM

GET ORGANIZED

IN THE BOX

TOOLS NEEDED

FIT AND SECURE

Strap Assembly

Assemble the Front and Rear Straps using M5 x 10 Button Head Bolts and M5 Nyloc Nuts (Items 7 & 8) as shown.
Place M5 Nut Caps on the Nyloc Nuts.

**** Ensure that the one end of the Strap Rubber (Item 1) is moved up against the end of the Rear Strap (Item 3).

**** Loosely fit the M6 Nyloc Nut and M6 x 12 x 1
Flat Washer (Items 17 & 18) to the T-Bolts at the ean for the Rear Strap as shown.

SLII SIDE PROFILE FITMENT
**** Choose where you would like to mount your Pro Water Tank, on your Front Runner Rack.
Assemble the M8 x 30 Hex Bolt and M8 Thin Nut (Items 11 & 12) as shown.
Loosen the rack corner and slide this assemble into the chosen combined slats T-slot.
Refit the Corner.

**** Assemble the M8 x 16 Button Head and M8 Thin Nut (Items 11 & 16) to the Rear Mount Bracket (Item 5).
Slide the assembly into the 3rd slat T-slot as shown.

**** Determine where the tank will be located before tightening the bolt assembly from 3.1 and the Mounting Bracket assembly from 3.2.
Ensure that both are in line before fully tightening.
Divide the T-Slot Rubber in two equal lengths and insert into the slats indicated (A).

Insert the Strap Assembly into the T-slot of the Rear Mount Bracket as shown.
Ensure that the M6 Washer sit on the inside of the Mount Bracket.
**** You will adjust the Strap using the M6 Nyloc Nut in 3.6.

**** Sure the front of the Strap to the M8 x 30 Hex Bolt inserted in 3.1 using a M8 Eye Nut and M8 Nylon Washer (Items 9 & 10) as shown.
Fully tighten the Eye Nut before moving to the next step.

Adjust the tension on the Strap by tightening the M6 Nyloc Nut.
After the tension is set correctly there should be no sliding movement from the tank on the slats.
**** If the tank is not in use, the Strap can be removed by sliding it out at the T-Slot of the Rear Mount Bracket.

Slim Sport / Van Rack Fitment

Choose where you would like to mount your Pro Water Tank Bracket.
Remove the Self Forming Screws from the chosen slat, lift the slat and slide two M8x20 Hex Bolts (item 15) in the bottom T-Slot.
For Van Rack Fitments there are no self forming screws to be removed.
Assemble the Z- Bracket (Item 4) using M8 Nyloc Nuts (Item 14) as shown.
Place M8 Nut Caps (Item 13) on the Nyloc Nuts.
Refit the Slat using the Self Forming Screws.
Assemble the M8 x 30 Hex Bolt and M8 Thin Nut (Items 11 & 12) the the Z – Bracket (Item 4) as shown

**** Assemble the M8 x 16 Button Head and M8 Thin Nut (Items 11 & 16) to the Rear Mount Bracket (Item 5).
Slide the assembly into the 3rd slat T-slot as shown.

**** Determine where the tank will be located before tightening the bolt assembly from 4.1 and the Mounting Bracket assembly from 4.2.
Ensure that both are in line before fully tightening.
Divide the T-Slot Rubber in two equal lengths and insert into the slats indicated (A).

Insert the Strap Assembly into the T-slot of the Rear Mount Bracket as shown.
Ensure that the M6 Washer sit on the inside of the Mount Bracket.
**** You will adjust the Strap using the M6 Nyloc Nut in 3.6.

**** Sure the front of the Strap to the M8 x 30 Hex Bolt inserted in 4.1 using a M8 Eye Nut and M8 Nylon Washer (Items 9 & 10) as shown.
Fully tighten the Eye Nut before moving to the next step.

Adjust the tension on the Strap by tightening the M6 Nyloc Nut.
After the tension is set correctly there should be no sliding movement from the tank on the slats.
**** If the tank is not in use, the Strap can be removed by sliding it out at the T-Slot of the Rear Mount Bracket.

Tank Assembly

**** When fitting the tap, apply thread tape to the thread of the tap.
This will allow the Tap to be aligned to your chosen position and have a water tight seal.

FINISH
Congratulations! You did it. Take a step back and admire your work!
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
Now’s the time to visit your favorite Front Runner Dealer in person or online.

Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters

BornToRoam

Share your adventures on:

WTAN073_REV_A00_A00
© 2023 FRONT RUNNER VEHICLE OUTFITTERS

References

• FRONTRUNNEROUTFITTERS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>