ELECTRONIC DXTY601 Universal Tire Pressure Sensor User Manual
- June 16, 2024
- Electronic
Table of Contents
ELECTRONIC DXTY601 Universal Tire Pressure Sensor
Product Information
- Specifications:
- User Manual No: BOYOTY
- Battery: Button battery
- Signal Type: Radio signal
- Frequency: 315MHz
- Compatible OE Numbers: 1472547, 1472547G, 1490701-01-C, 1490701-01-B, 1490700-00-B
Product Usage Instructions
- Installation:
- We recommend that you have the tire pressure sensor installed by a tire repair shop or another experienced shop. They will have the necessary tools and expertise to properly install the sensor.
- Tire Pressure Setting:
- After the sensor has been changed, it is mandatory to set the tire pressure to the required value, such as 280KPa. Follow these steps:
- Use a tire pressure gauge to measure the current tire pressure.
- If the pressure is not at the required value, use an appropriate air compressor to inflate or deflate the tire until the desired pressure is reached.
- Drive for 10 Minutes:
- After setting the tire pressure, drive your vehicle for at least 10 minutes. During this time, the tire pressure alarm lamp should disappear. If it does not, please contact your seller for further assistance.
- Frequently Asked Questions (FAQ):
- Can I install the tire pressure sensor myself?
- We recommend having the sensor installed by a tire repair shop or an experienced shop to ensure proper installation.
- What should I do if the tire pressure alarm lamp does not disappear after driving for 10 minutes?
- If the tire pressure alarm lamp does not disappear after driving for 10 minutes, please contact your seller for help and further assistance.
- Is the product compliant with FCC regulations?
- Yes, this device complies with part 15 of the FCC Rules. It is designed to not cause harmful interference and must accept any interference received.
- Are there any radiation exposure limits to consider?
- Yes, for mobile device usage, it is recommended to maintain a minimum distance of 20cm between the radiator (sensor) and your body to comply with FCC radiation exposure limits.
PRODUCT INTRODUCTION
Tire pressure sensor user manual
- No: BOYOTY
- Statement: There is a button battery in the sensor. The sensor sends the signal by radio signal, pls make sure the sensor is suit for your car. The sensor works in the 315MHz
Plus, make sure your replaced sensor OE No. is one of them:1472547/1472547G/1490701-01-C/1490701-01-B/1490700-00-B. If not, pls contact your seller to confirm the OE No.
- For tire pressure sensor installation, we recommend the user go to a tire repair shop or another experienced shop to change the sensor.
- After changing, the mandatory requirement is that the tire pressure should be set at the required value like 280KPa . Drive for 10 minutes, tire pressure alarm lamp will disappear. If not, pls contact with your seller for help
FCC
FCC Warning Statement
- This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.