LA CROSSE Atomic Digital Wall Clock User Guide

LA CROSSE Atomic Digital Wall Clock

LA CROSSE Atomic Digital Wall Clock

Full manual can be found under the Support tab here: bit.ly/513-1417v5

POWER UP

1. Insert 2-AA batteries into your Outdoor Sensor.
2. Insert 2-AA batteries into your Clock.
3. Adjust time and date settings on your Clock.
4. Once the Outdoor Sensor is reading to your clock, place it outside in a shaded location.

Watch sensor mounting video: http://bit.ly/TH_SensorMounting

WWVB ATOMIC TIME SIGNAL

• The station will automatically search for the atomic time signal at UTC 7:00, 8:00, 9:00, 10:00, and 11:00.
• Press and release the SET button to manually search for the WWVB atomic time signal.
• For information about WWVB Atomic time visit: http://bit.ly/AtomicTime

SETTINGS

1. Hold the SET button to enter Settings Menu.
2. Use the + or – buttons to adjust values.
3. Press the SET button to confirm and move to next item.

Settings Menu Order:

Note : When Español or Francais is selected, the following instructions and weekday will be presented in that language.

Note : Weekday sets automatically when Year, Month and Date are set.

TIME ALARM

Set Alarm Time:

1. Hold the ALARM button to enter ALARM settings menu.
2. Use the + or – buttons to adjust values.
3. Press the ALARM button to confirm and move to next item.

Activate/Deactivate Alarm:

• The alarm is active when set.
• Press and release the ALARM button to deactivate or activate the alarm.
• The Clock Icon will show when alarm is active.

Snooze:

• When the alarm sounds, press the SNOOZE button to silence the alarm for 10 minutes.
• Snooze can be repeated as desired.

HI | LO TEMPERATURE RECORDS

• Press the PLUS (+) button to view HI Temperature.
• Press PLUS (+) button again to view LO Temperature.
• Hold the PLUS (+) button for 5 seconds to reset HI and LO temperature records.

Note : All records reset at midnight everyday

MOON PHASE

The Moon Phase is based on the lunar calendar, and therefore is controlled by the time and date set on your weather station.

SEARCH FOR OUTDOOR SENSOR

• Hold the MINUS (-) button for 3 seconds to search for the sensor.
• The Reception Indicator will flash until the sensor signal is received, if no signal is available the search will stop after 3 minutes.
• The Reception Indicator will show solid on screen when the sensor is connected.

LOW BATTERY INDICATOR

• When Battery Indicator shows next to outdoor temperature, replace batteries in the Outdoor Sensor.
• When Battery Indicator shows next to the time, replace batteries in the station.

SPECIFICATIONS

Indoor Temperature Range : 32°F to 122°F (0°C to 50°C)

Outdoor Temperature Range : -40°F to 140°F (-40°C to 60°C)

Transmission Range:
Over 330 ft. (100 meters) RF 433MHz (open air)

Power Requirements:
513-1417v5 – 2 AA batteries (not included)
TX141-Bv3 – 2 AA batteries (not included)

Battery Life:
513-1417v5-over 12 months
TX141-Bv3-over 12 months

Dimensions :
513-1417v5- 11.10” W x 1.14” D x 6.75” H
(28.19 W x 2.89 D x 17.15 H cm)
TX141-Bv3- 1.57” L x 0.79” W x 5.12” H
(3.98 L x 2.0 W x 13.0 H cm)

SENSOR WEATHER SHIELD-NOT INCLUDED

The Sensor Weather Shield is designed to protect your outdoor sensor from rain and snow. This shield will offer limited protection from the sun’s heat.
Purchase at: http://bit.ly/925-1418

WE’RE HERE TO HELP!

If you require additional support, call or customer support team based out of La Crosse, Wisconsin.

Phone: 1.608-782-1610

Or fill out our online support request form here: bit.ly/contact_techsupport

Our knowledgeable support team is available: Monday-Friday, 8am-6pm CST

JOIN THE CONVERSATION

Ask questions, watch detailed setup videos, and provide feedback on our social media outlets!

WARNING : This product can expose you to chemicals including styrene, which is known to the State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov

WARRANTY INFO

La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of purchase) on this product relating to manufacturing defects in materials & workmanship. .
For Full Warranty Details, Visit: www.lacrossetechnology.com/support

CARE + MAINTENANCE

• Do not mix old and new batteries.
• Do not mix Alkaline, Lithium, standard, or rechargeable batteries.
• Always purchase the correct size and grade of battery most suitable for intended use.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the batteries have with correct polarity (+ / -).
• Remove batteries from equipment that will not to be used for an extended period.
• Promptly remove expired batteries

CANADA STATEMENT

This device complies with CNR Industry Canada license -exempt devices. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Increase separation between equipment & receiver.
• Consult the dealer or an experienced radio/TV technician for help.

This device must not be co-located or operating in conjunction with any other antenna or transmitter. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

CAUTION

The manufacturer is not responsible for any radio or TV interference caused by unauthorized changes or modifications to this equipment. Such changes or modifications could void the user authority to operate the equipment.

All rights reserved. This manual may not be reproduced in any form, even in part, or duplicated or processed using electronic, mechanical or chemical process without the written permission of the publisher.

This booklet may contain errors or misprints. The information it contains is regularly checked and corrections are included in subsequent editions. We disclaim any responsibility for any technical error or printing error, or their consequences. All trademarks and patents are recognized.

FAQ’S

How do I set the time?

Press and release the SET button to enter the TIME menu. Use the + or – buttons to adjust values. Press the SET button to confirm and move to next item.

How do I set the date?

Press and release the SET button to enter the DATE menu. Use the + or – buttons to adjust values. Press the SET button to confirm and move to next item.

How do I set my location?

Press and release the SET button to enter LOCATION menu. Use the + or – buttons to adjust values. Press the SET button to confirm and move to next item.

How do I set my language?

Press and release the SET button to enter LANGUAGE menu. Use the + or – buttons to adjust values. Press the SET button to confirm and move to next item.

What can affect an atomic clock?

External influences, such as electromagnetic fields, can influence the energy levels of the states and thus also the transition frequency. Atomic clocks are therefore shielded at great expense, and special pairs of electrical configurations are selected that are as insensitive as possible to external interference.

Do atomic clocks ever stop working?

If the budget is passed as proposed, after WWVB is closed your atomic clock synchronized devices will no longer be accurate, nor will they automatically be able to toggle the time between Standard to Daylight Savings Time. They’ll continue to operate, albeit without a self-setting function

What is the wave button on an atomic clock?

The WAVE button can be used to attempt forced signal receipt. To activate, hold the WAVE button down for 3+ seconds. Once the WAVE feature is activated, the hands will automatically reset to the 12:00 position, and the movement will attempt to force a signal receipt from Fort Collins, Colorado.

How do you adjust an atomic clock?

Atomic Clocks may also be set manually and be very accurate. Simply insert the battery, press your time zone and then press the flap just above the left side of the battery. Hold until you reach the correct time and then release. Your clock is now an accurate quartz clock until it will find the signal.

Will an atomic clock change daylight savings time?

Daylight Saving Time has never been used here. Clocks do not change in International Atomic Time, Time Standard. There is no previous DST change in Time Standard.

Does an atomic clock need batteries?

Do I need to change the batteries in my SkyScan Atomic Clock when I change my smoke alarm batteries? It is not necessary to change your battery that often. Change the batteries when the numbers on the clock begin to fade.

How do I turn off the alarm on my atomic clock?

Enter ALARM SET MODE at any time by pressing and holding the “ALARM ON/OFF“ button for 5 seconds. To Turn Alarm off: Press and release the “ALARM ON/OFF” button. The “ “ icon will disappear and the words “ALARM OFF” will appear on the clock.

Why is my atomic clock flashing?

The clock time blinks if it is not set or after power interruption (without back-up battery installed). When AC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless batteries are installed)..

LA CROSSE Atomic Digital Wall Clock
www://lacrossetechnology.com/products/513-1417v5

References

• 513-1417V5 Atomic Digital Wall Clock – La Crosse Technology
• 925-1418 Sensor Weather Shield – La Crosse Technology
• Radio Station WWVB | NIST
• YouTube
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>