ZEVNI A04761C6 Rudolf 27 Inch Wide Black and Brass 6 Light Kitchen Island Light Instruction Manual
- June 11, 2024
- ZEVNI
Table of Contents
- ZEVNI A04761C6 Rudolf 27 Inch Wide Black and Brass 6 Light Kitchen Island
- Product Information
- Product Usage Instructions
- SAFETY WARNING
- IMAGE FOR FINISHED PRODUCT
- TOOLS REQUIRED NOT INCLUDED
- PARTS TYPE & QTY INCLUDING
- ASSEMBLY & INSTALLATION INSTRUCTIONS
- **ORDERING PARTS
- **CLEANING
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEVNI A04761C6 Rudolf 27 Inch Wide Black and Brass 6 Light Kitchen Island
Light
Product Information
The product is a ceiling lamp with six glass shades and a fixture body. It requires a voltage of 120V and uses Type B bulbs with a maximum wattage of 40W per bulb. The lamp should be kept away from acidic and alkaline substances to avoid damaging the surface of the lamp. The product comes with a round mounting plate, green ground screw, canopy, loop, knob nut, quick link, stem, socket, plastic wire connector, and mounting screw. Warning: To reduce the risk of fire, electric shock, or personal injury, we suggest installation by a licensed electrician. Before starting any work, turn off the electricity. Ensure that the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Check that the ceiling or wall can support the weight of the lamp before installation.
Product Usage Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Assemble stems together onto the top of the fixture body.
- Pass the fixture wires through loops and canopy. Pull gently to ensure that the wires are not stressed.
- Turn off power before starting the installation.
- Make installation ensuring that the mounting plate is at least 6″.
- Connect wires according to the chart provided. Twist wires together with plastic wire connectors until tightly joined and wrap each connector with approved electrical tape. Ensure no wire strands are exposed and carefully tuck all wires into the outlet box.
- Attach fixture body to mounting plate using the preassembled screws on the mounting plate.
- Carefully screw glass shades onto sockets.
- Check that everything is installed properly before turning on the light. Enjoy!
Item Number: A04761C6
SAFETY WARNING
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Ensure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B,Max 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED NOT INCLUDED
Before starting assembly and installation please prepare the needed tools as below picture.
PARTS TYPE & QTY INCLUDING
- (C) Round mounting plate (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Loop (4)
- (G) Knob nut (2)
- (H) Quick link (2)
- (I) Stem
- (J) Glass shade (6)
- (K) Socket (6)
- (L) Fixture body (1)
ACCESSORIES & QTY ENCLOSED
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Make pre-installation
- Step A1: Choose the needed stems (I), and pass fixture wires through the chosen stems (I), then screw stems (I) together onto the top of fixture body (L).
- Step A2 : Attach quick links (H) to loops (F) on canopy (E) and the top of stems (I). Carefully pass the fixture wires through loops (F) and canopy (E). Gently pull the wires to ensure the wires are not stressed.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
-
Make installation
- Step B1 Unscrew knob nuts (G) from mounting plate (C).
- Step B2 Attach the mounting plate (C) to the outlet box with mounting screws (B).
- Step B3 If needed, shorten the fixture wires’ length. At this point, the remaining wire length measured above the mounting plate (C) is at least 6″.
- Step B4 Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
-
Step B5
Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto pre-assembled screws on mounting plate (C).
NOTE:
Canopy (E) should be snug against the ceiling with knob nuts (G). If not, remove canopy (E), and adjust the threaded length of preassembled mounting screws on the mounting plate assembly (C). -
Step B6
1. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
2. Carefully screw glass shades (J) onto sockets (K).
Check everything is already installed properly, then you could turn on the light. Enjoy!
**ORDERING PARTS
**
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
**CLEANING
**
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
- +1 850 296 2377 Working hours:
- Mon – Fri 9:00 a.m. – 16:00 p.m. EST
- service@zevni.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>