LINKSYS E1000 Wireless N Router Instruction Manual
- June 16, 2024
- Linksys
Table of Contents
LINKSYS E1000 Wireless N Router
Hardware Specs
- Model: Linksys_E1000
- Version: 1
Install Procedure
- Read the Firmware FAQ and Peacock Announcement.
- Download a trailed mini build (mini_e1000v1.bin) from the broadcom_K26 folder.
Performing a Hard Reset
To perform a hard reset on the E1000v1, follow these steps:
- Perform a normal 30/30/30 reset.
- Login to http://192.168.1.1/ and you will see the Linksys – Management Mode page.
- Click Reboot then after a moment, you will see “Command reboot completed.” and reboot again.
- When the lights return to their normal state, click Continue to the router GUI main page.
Linksys_E1000
WARNING : This is only for version 1 hardware. For version 2: Linksys_E1000_v2.0
Hardware Specs
- FCC ID: Q87-E1000
- Industry Canada ID: 3839A-E1000
- CPU: Broadcom BCM4716B0 @300 MHz
- Flash / RAM: 4 MiB / 32 MiB
- Wireless/Ethernet chip: Broadcom BCM4716B0
- Wireless protocols: bgn
- Wireless MIMO config: 2×2:2
- Switch: Broadcom BCM5325E
- LAN / WAN: 4 / 1 (up to 100 Mb/s)
E1000v1 thread for information and DD-WRT compatibility: Linksys E1000 now supported (V.1 ONLY!)
Install Procedure
- Read the Firmware FAQ and Peacock Announcement.
- Download a trailed mini build (mini_e1000v1.bin) from the broadcom_K26 folder.
- Do not use a build bigger than 3712 KB (3801088 bytes)
- If you wish to experiment with a newer build, read it’s build thread before flashing!
- Set a static IP on your computer e.g. 192.168.1.7 and subnet mask 255.255.255.0
- Connect an Ethernet cable from your computer to a router LAN port and disable wireless ¨ Recommended to disconnect other cables
- Perform a hard reset.
- Navigate to http://192.168.1.1/ for the Linksys web GUI Go to the Linksys Administration->Firmware Upgrade page.
- Do not give the reboot command. You will use this page to upgrade your firmware.
- Browse to the downloaded firmware and click Upload.
- Do not touch anything. The page will tell you that the upgrade was successful and the router is now rebooting. Your router may take upwards of a couple minutes to reboot. Watch the lights… once the wireless and power indicators are on steadily for several seconds, your router is fully rebooted and you can click “Continue” in your browser window..
- If the DD-WRT password change page displays, your upgrade has been successful, and you must now perform another hard reset. This time, when you navigate to http://192.168.1.1/, click “Reboot” and wait for the router to come online again so you can configure it. 10.
- For upgrades use any non-trailed and non-nv6xk builds (e.g. K2.6_mini.bin) no bigger than 3712 KB (3801088 bytes)
Linksys_E1000
- Do not use any build older than 15264 which are prior to v1 support
- See Where do I download firmware? for download and firmware info
If the DD-WRT password change page does not display, your page request times
out, or you can’t ping 192.168.1.1, make sure both wireless and power lights
are on steadily first, then do a hard power cycle (unplug the power from the
router–do not do a 30/30/30 reset). Wait a few seconds and plug the power back
into the router. Wait until both wireless and power lights are on steadily,
then navigate to http://192.168.1.1/in your browser of choice again. If the
DD-WRT password change page displays, your upgrade has been successful, and
you must now perform another hard 30/30/30. This time, when you navigate to
192.168.1.1, click “Reboot” and wait for the router to come online again so
you can configure it.
You can also flash the same firmware of TomatoUSB as described for
WRT160N_v3.0 Firmware version 33555 dated 10/20/17 runs on this router, but
doesn’t have the final Broadcom fix for the KRACK vulnerability in WPA2. KRACK
fixes for Broadcom were completed in ?SVN 33678, but build 33679 is missing
many files, so it is recommended to use 33772 or newer, after reviewing New
Build threads.
Performing a Hard Reset
Procedure for an E1000v1
- Perform a normal 30/30/30 reset.
- Login to http://192.168.1.1/ and you will see the Linksys – Management Mode page.
- Click “Reboot” then after a moment, you will see “Command reboot completed.” and reboot again.
- When the lights return to their normal state, click “Continue” to the router GUI main page.
Serial Recovery
- First see Serial Recovery and reference the serial pinout (E1000v2).
- Once at the CFE prompt you need to assign an IP/Subnet mask to eth0. I’m not sure if eth0 is the router’s interface to the switch or one specific port but I had a CAT5 cable hooked up to port 1 on the router and it worked.
- Type ifconfig eth0 to show no address assigned to the interface. This will assign an address/mask:
- CFE> ifconfig eth0 addr=192.168.1.1 mask=255.255.255.0
- Now you can flash using a TFTP client from a computer, plugged in to port 1 on the router (Serial Recovery):
- flash -ctheader : flash1.trx
JTAG
JTAG for the E1000_V1 (and WRT160Nv3): Barryware JTAG thread
Install Procedure
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>